• Journal of the Korean Wood Science and Technology
• /
• v.32 no.3
• /
• pp.25-32
• /
• 2004

This research work explored physical and mechanical properties of impregnated sawdust boards from three softwood species (P, densifora, L. kaemferi, and P. koraiensis) with phenol-formaldehyde (PF) resin by various vacuum treatment methods of combining pressure, vacuum, and ultrasonic waves. Simultaneous vacuum and ultrasonic wave treatments with no pressure resulted in the greatest increase in resin content, density, dimensional changes (thickness and length), bending strength, and hardness of impregnated board. This result seemed to be attributed to the ultrasonic wave treatment.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.454-460
• /
• 2012

The nano-sized zirconia powders were synthesized in an impregnation method using pulp and $ZrOCl_2{\cdot}8H_2O$ as an initial material. The synthesized powders were characterized by XRD and FE-SEM. The particle size of the powder was controlled by preparation conditions, such as drying temperature and time. As a result of the various drying and calcination conditions, 30~50 nm sized homogeneous zirconia particles were obtained at $800^{\circ}C$ for 1 h. Crystallization and the rapid growth of particles were accelerated with increasing calcination temperature and time. Tetragonal phase generated below $800^{\circ}C$ were transferred to monoclinic phase with increasing calcination temperature and time. Moreover, above $800^{\circ}C$, heat treatment time had very large influence on the particle growth, and the change of drying condition also had large influence on the growth of a crystal.

• Design & Manufacturing
• /
• v.16 no.2
• /
• pp.60-65
• /
• 2022

In the pultrusion process for the CFRP (Carbon fiber reinforced plastic) rectangular pipe, the drawing device is eseential which can continuously produces products and draws the carbon fiber tow. In addition, since the degree of cure changes depending on the temperature and the temperature ditribution of the curing mold changes depending on the pultrusion speed, the temperature distribution of the curing mold under certain conditions must be studied before processing. In this study, in the pultrusion process using a closed impregnation method, which has several advantages compared to the general pultrusion process using a open bath impregnation method, the drawing force required to pull the carbon fiber tows and the temperature distribution of the curing mold was analyzed to design the drawing device and the curing mold efficiently.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.823-828
• /
• 2002

Concrete used up to date semipermanent architecture material but now day concrete early deterioration emboss social issue because of construction structure and environmental factor. so, many study of deterioration concrete construction improve durability used impregnation alkalization agent. Impregnation alkalization agent deterioration concrete construction spray infiltration or diffusion improve alkali and filler inter minuteness void elaborateness constitution concrete. but many study of harding concrete change inter minuteness void that Is insufficiency also, To study of method recover shape impregnation alkalization agent apply deterioration concrete construction. impregnation alkalization agent infiltration according to test of porosity, premeameter, absorption.

• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.379-384
• /
• 2009

Zirconia is widely used for structural materials in machinery due to its superior properties, such as high strength, high hardness, and high toughness. Zirconia generally has ivory or white color. Therefore many studies are performed for diversification of zirconia color, in order to be widely uitilized for decoration and machine parts which need distincfive color. In this study, graphite is used to prevent structural defect, to maintain superior properties, and to develop black color of zirconia by impregnation method. As specimen was impregnated at $1600^{\circ}C$ for 2 h, bending strength is 1221 MPa, density is $6.01\;g/cm^3$, hardness is 10.1 GPa, absorption coefficient is 0%, transmittance is Fail, chromaticity is 54. The results indicate that black zirconia has enough properties to be adopted as mechanical parts. Optimum impregnation time is 2 h for various observations.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.130-137
• /
• 2014

Nondestructive evaluation (NDE) method by using a resonance frequency mode was carried out for ceramics made from particle boards with different phenol resin impregnation ratios (30, 40, 50, 60%) at carbonizing temperature of $800^{\circ}C$. The material for ceramics was Miscanthus sinensis var. purpurascens board. Dynamic modulus of elasticity increased with increasing impregnation ratio. There was a close relationship of dynamic modulus of elasticity and static bending modulus of elasticity to modulus of rupture (MOR). However, the result indicated that correlation coefficient is higher in dynamic modulus of elasticity to MOR than that in static modulus of elasticity to MOR. Therefore, the dynamic modulus of elasticity using resonance frequency by free vibration mode is more useful as a nondestructive evaluation method for predicting the MOR of ceramics made from Miscanthus sinensis var. purpurascens particle boards by different phenol resin impregnation ratios.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.2
• /
• pp.80-86
• /
• 2020

This paper is concerned with type of imperfections present within the anodic oxide films on AA2024 and surface hardness of the anodic film measured after ink-impregnation. The anodic oxide films were formed for 25 min at 40 mA/㎠ and 15±0.5℃ and 300 rpm of magnet stirring rate in 20% sulfuric acid solution. The ink-impregnation allows clear observations of not only the imperfections within the anodic oxide films but also an indentation mark on the oxide film surface made by a pyramidal-diamond penetrator for the hardness measurement. There were observed four different regions in the anodic oxide films on AA2024 and the surface hardness of the anodic oxide films appeared to be crucially dependent on the type of defects, showing 60~100 H_v on the oxide surface region I with large size black defect, 100~140 H_v on the oxide surface region II with large size grey defect, 140~170 H_v on the oxide surface region III with mall size black and/or grey defects and 170~190 H_v on the oxide surface region IV without defects. The pyramidal indentation marks were observed to be distorted in the regions with a large size black and grey defects, while no distortion of the indentation mark was observed in the regions with small size defects and without visible defects.

• Korean Journal of Materials Research
• /
• v.11 no.10
• /
• pp.846-850
• /
• 2001

In the present study, nano-size powders of ternary ferrites, $Ni_{0.5}Zn_{0.5}Fe_2O_4$, as the potential catalysts of $CO_2$decomposition, were prepared by the wet processing of hydrothermal synthesis and coprecipitation method, and the catalyzing effects of impregnation of the noble metals, Pt and Pd, onto $Ni_{0.5}Zn_{0.5}Fe_2O_4$for the $CO_2$decomposition were investigated. XRD results of the synthesized ferrites showed a typical spinel structure of ferrite and the particle size was very small as about 6~10 nm. BET surface area of the ternary ferrites was not affected by the impregnation of Pt and Pd. The reactivity of the $CO_2$decomposition to carbon was improved by the impregnation of the noble metals of Pd and Pt. The effect of Pd-impregnation on the $CO_2$decomposition rate was higher than Pt-impregnation.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.240-244
• /
• 1998

The analytical method was developed to calculate efficiency of densifying carbon/carbon (C/C) composites using coal tar pitch as a matrix precursor at each cyle. Three factors were defined in analyzing the densification process: impregnation efficiency, retention efficiency, and overall densification efficiency. The relationships developed were applied to the experimental results for three densification cycles of C/C composites with pitches as an impregnant to evaluate the factors which may depend on the impregnant and on the route of carbonization. The impregnation efficiency increased with the repeated process cycles whereas the retention efficiency decreased irrespective of the impregnant and carbonization route. Carbonization route P+A+G, in which pressure carbonizationl (P) and graphitization (G) were done before after atmospheric pressure carboniztion (A) respectively, using impregnant of high carbon yields was the most effective method in densifying C/C composites.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12a
• /
• pp.280-282
• /
• 2011

Silica-gold composite particles were prepared by wet chemical route including impregnation method. Obtained composite particles were characterized using FE-SEM, and XPD.