• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.9C
• /
• pp.871-878
• /
• 2002

The cartesian loop chip which is one of key devices in narrow-band Walky-Talky transmitter using RZ-SSB modulation method was designed and implemented with 0.35 ㎛ CMOS technology. The reduced size and low cost of transmitter were available by the use of direct-conversion and cartesian loop chip, which improved the power efficiency and linearity of transmitter. In addition, low power operation was possible through CMOS technology. The performance test results of transmitter showed -23㏈c improvement of IMD and -30㏈c below suppression of SSB characteristic in the operation of cartesian loop chip (closed-loop). At that time, the transmitting power was about 37㏈m (5W). The main parameters to improve the transmitting characteristic and to compensate the distortion in feed back loop such as DC-offset, loop gain and phase value are interfaced with notebook PC to be controlled with S/W.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11B
• /
• pp.1005-1016
• /
• 2006

As the increment usage of Internet, the security systems's importance is emphasized. The current Internet Key Exchange protocol(IKE) which has been used for key exchange of security system, was pointed out a problem of efficiency and stability. In this research, we try to resolve those problems, and evaluate the newly designed Key Exchange protocol in the IPsec interaction test bed system environment. In this research we implemented the new Key Exchange Protocol as a recommendation of RFC proposal, so as to resolve the problem which was pointed out the key exchange complexity and the speed of authentication process. We also designed the defense mechanism against the Denial of Service attack. We improved the key exchange speed as a result of simplification of complex key exchange phase, and increased efficiency as a result of reuse the preexistence state value when it's renegotiated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6C
• /
• pp.267-274
• /
• 2012

The conventional approach to evaluate the contaminant transport in soils adopts the macro-scale implementation while the pore configuration and network is a dominant factor to determine the fate of contaminant. However, the observation of fate and transport at pore scale may not be readily approachable because of the computational expenses to solve Navier-Stokes equation. We herein present the 2D Lattice-Boltzmann method that enables to assess the local fluid velocity and density efficiently for the case of single phase and multi-components. The solute fate spatio-temperal space is explicitly determined by the advection of fluid flow. Two different types of idealized pore space provides the path of fluid. Also, solute transport, the velocity field and average concentration of solute are computed in steady state. Results show that the pore geometry such as tortuosity mainly affect the solute fate. It highlights the significance of the pore configuration and shape in granular soils and rock discontinuity in spite of the equivalent porosity.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.2
• /
• pp.154-161
• /
• 2013

This paper presents the signal-to-interference plus noise ratio (SINR) estimation of IEEE 802.16m WirelessMAN-Advanced mobile station with simulation and implementation results. The downlink signal of IEEE 802.16m has two kinds of A-Preambles: the PA-preamble and the SA-preamble. This paper proposes the efficient method of estimating SINR with A-Preambles, by measuring noise power from PA-preamble and measuring interference power and signal power from SA-preamble. The proposed SINR measurement block contains important features such as subcarrier phase rotation elimination and simplified dB transform. The result of this paper is integrated to ETRI's IEEE 802.16m test mobile station, used for decision of adaptive-modulation-and-coding (AMC) and hand-over. It showed good measurement performance in simulation and unified system link test also.

• Journal of Advanced Navigation Technology
• /
• v.9 no.1
• /
• pp.61-69
• /
• 2005

TCP and UDP is a transport layer protocol of Internet. TCP is a connection oriented protocol which supports a reliable data transfer by offering error and flow control, but it bring a transmission delay. On the other hand, the UDP is a connectionless protocol which does not carry out error and flow control, but it guarantees a realtime transmission. There are hardly any protocols which supports not only realtime functions but also data reliability. In this paper, we have designed and implemented a new TCP mode option which supports reliable realtime transmission. Our designed TCP performs an error recovery process during a fixed amount of time. This time is negotiated during the connection establishment phase. Our designed TCP is tested in real environments, and we find that it is relatively faster than the standard TCP and more reliable than the UDP. It can be used for the reliable transfer of realtime multimedia data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1097-1106
• /
• 2011

In this paper, we present design method of wideband single-sideband mixer(SSM) with excellent sideband suppression and carrier suppression. We proposed SSM with 4-band split structure for uniform output flatness. From circuit simulation of this structure using Microwave OfficeTM, we got satisfactory results. We realized a SSM based on this results, then we experimented. The measured results show excellent agreements with the simulated results. We compared with two SSM's(target SSM(M Co. SM0218LC1CDC SSM) and our SSM) as well. The presented SSM is 3.35 times bigger, but sideband suppression is 3 dBc better and carrier suppression is 8 dBc better than those of comparative SSM, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5403-5408
• /
• 2012

In this paper, we introduce the multiple frequency bio-electrical impedance analysis method for body composition analysis. And then we implement the multiple frequency bio-electrical impedance analysis system. Overall system consists of: multiple frequency alternating current signal generator contained alternating current signal, phase signal detector, voltage signal detector, micro controller, in-out device(key-pad LCD), conductivity electrodes, system power. We explain the architecture of the system and required theory to implement the system. In order to investigate the clinical significance of the body composition data, compare to the data measured by the expert body composition analyzer which provide high reproduction and precision. Finally, experimental results which are the correlation between the measured data show the very high reproduction performance of the body composition analysis in the proposed system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.1A
• /
• pp.28-34
• /
• 2011

In this paper, we proposed the architecture of the Hybrid Quadrature Polar transmitter which has the wideband characteristics available for the SRD(Short Range Device). First, we developed the simulation environment and carried out performance degradation analysis. Second, we considered the slewrate of the VVA(Voltage Variable Attenuator), time delay between magnitude signal and phase signal and the number of bits for DAC(Digital-to-Analog Converter) as the main performance factors. Then we obtained the minimum required values to meet the transmitting performance requirements of 3GPP standards through simulation results. Based on these results, we implemented the Wideband Hybrid Quadrature Polar transmitter platform and varified the performance requirements through practical measurement.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.515-519
• /
• 2004

A Propeller-Anemometer is an instrument used specifically, to measure the wind speed. The accurate measurement of the wind speed is vitally important such required by any weather stations. In this research, the measurand of the instrumentation was the rotational speed of the propeller and the instrumentation result or output data was wind velocity. The speed measured was recorded digitally in the computer by using specific software. A specific sensor used to measure a variable by converting information of the variable (rotational speed of the propeller) into a dependent signal such as electrical signal in form of voltage. The development of Propeller-Anemometer involved few sets of instrumentation process and equipment. It included three major parts, mechanical, electronics and computer. The main instrumentation processes were physical and signal interfacing, signal conditioning, logic interfacing, data transmission to computer and processing the data. Generally, this paper presents the overall concept and design of Propeller-Anemometer Instrumentation. However, an emphasis was mainly in designing and building the interfacing system, hardware and software. Basically, for the first phase of the development, this project designed and built the RS232 terminal using Peripheral Interface Controller (PIC), PIC16F873. The hardware can be interfaced to computer or other compatible devices. This routine converted input voltage from the circuit to speed (velocity) and transmitted them afterwards to the target device by using the RS232 transmission protocol. This implementation implied a computer display as visual interface. For the purpose of this paper, RS232 data transmission was carried out using a Microsoft Visual Basic software routine.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1714-1728
• /
• 2016

This paper presents improved harmonics extraction based on Adaptive Linear Neuron (ADALINE) algorithm for single phase photovoltaic (PV) shunt active power filter (SAPF). The proposed algorithm, named later as Improved ADALINE, contributes to better performance by removing cosine factor and sum of element that are considered as unnecessary features inside the existing algorithm, known as Modified Widrow-Hoff (W-H) ADALINE. A new updating technique, named as Fundamental Active Current, is introduced to replace the role of the weight factor inside the previous updating technique. For evaluation and comparison purposes, both proposed and existing algorithms have been developed. The PV SAPF with both algorithms was simulated in MATLAB-Simulink respectively, with and without operation or connection of PV. For hardware implementation, laboratory prototype has been developed and the proposed algorithm was programmed in TMS320F28335 DSP board. Steady state operation and three critical dynamic operations, which involve change of nonlinear loads, off-on operation between PV and SAPF, and change of irradiances, were carried out for performance evaluation. From the results and analysis, the Improved ADALINE algorithm shows the best performances with low total harmonic distortion, fast response time and high source power reduction. It performs well in both steady state and dynamic operations as compared to the Modified W-H ADALINE algorithm.