• Journal of the Korea Institute of Building Construction
• /
• v.16 no.6
• /
• pp.505-512
• /
• 2016

Even though high performance concrete was developed according to the trend of bigger and higher of reinforced concrete building, the rheological evaluations such as viscosity, yield stress are not enough to use as input data to accomplish the numerical analysis for the construction design. So there are many problems in the harden concrete such as poor compaction, rock pocket and crack, etc. in the field. In this study, consistency curves were measured by the viscometer as hydration reaction time passed. At the same time the slump flow test and Vicat setting test were carried out for comparing with the results of rheological properties. The fluidity of the W/B 30% decreased as the increase of replacement ratio of blast furnace slag. But in case of W/B 40%, the replacement ration did not significantly influenced to the slump flow value with the passage of hydration time. By the replacement of blast furnace slag to cement, initial setting was delayed and the time gap between initial and final setting became shorten. Through the regression analysis using Bingham model, there are a sudden changes of viscosity and yield stress around initial setting in case of low W/B 30%. The increase of workability by the change of free water in cement paste was offset by the coating effect of impermeable layer in case of W/B 40%.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.3
• /
• pp.395-406
• /
• 2016

Population and development are concentrated by urbanization. Consequently, the usage of underground area and the riverside area have been increased. By increasing impermeable layer, the urban basin drainage is depending on level of sewer. Flood damage is occurred by shortage of sewer capacity and poor interior drainage at river stage. Many of researches about flood stress the unavailability of connection at the river stage with the internal inundation organically. In this study, flood calculated considering rainfall and combined inland-river. Also, using urban runoff model analyze the overflow of sewer. By using results of SWMM model, using flood inundation analysis model analyzed internal drainage efficiency of drainage system. Applying SWMM model, which results to flood inundation analysis model, analyzes internal drainage efficiency of drainage system under localized heavy rain in a basin of the city. The results of SWMM model show the smoothness of internal drainage can be impossible to achieve because of the influence of the river level and sewer overflow appearing. The main manholes were selected as the manhole of a lot of overflow volume. Overflow reduction scenarios were selected for expansion of sewer conduit and instruction retention pond. Overflow volume reduces to 45% and 33~64% by retention pond instruction and sewer conduit expansion. In addition, the results of simulating of flood inundation analysis model show the flood occurrence by road runoff moving along the road slope. Flooded area reduces to 19.6%, 60.5% in sewer conduit expansion scenarios.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.97-105
• /
• 2007

수문학적 토양유형은 복잡하게 세분되어 있는 토양의 종류를 수문학적인 목적에 따라 단순화하기 위해 만든 것으로 미농무성 토양보전국에서 고안한 개념이다. 우리나라 토양을 이 방법으로 구분하고자 하는 몇번의 시도가 있으며 그 중 대표적인 것이 정 등(1995)이 분류한 수문학적 토양군이다. 이는 토양의 침투 투수특성에 대한 실측자료가 부족한 우리나라의 실정을 감안하여 토성속(textural family), 배수등급(drainage class), 불투수층(impermeable layer), 투수성(permeability)의 네가지 토양특성을 분류특성으로 하여 각각에 1-4점 범위로 점수를 매긴 후 합산한 점수를 기준으로 수문학적 토양유형을 분류하는 것이다. 최근에는 토양의 한계침투속도에 따라 수문학적 토양유형을 분류하고자 하는 시도가 있으며 본 논문에서는 새로운 방법으로 분류할 때 기존의 방법과 어떠한 차이가 있는지 비교하고자 하였다. 정 등(1995)의 분류방법은 개념상 몇가지 문제점을 안고 있다. 먼저 토양의 수리특성은 같은 토성속이라 하여도 토양생성 과정과 토지이용 방법에 따라 그 차이가 매우 큼에도 불구하고 이에 대해 고려하지 못하였으며 다음으로 지표유거가 많아 배수가 양호한 토양의 강우 유출을 과소평가한다. 또한 얕은 토심에 존재하는 불투수층이 존재하는 경우 토양의 수리특성에 관계없이 적은 양의 강우에도 유출이 발생하므로 별도의 제한인자로 간주하여야 한다. 토양의 한계 침투속도를 이용한 분류방법은 이러한 문제점을 상당 부분 개선할 수 있다. 토양의 한계침투속도를 산정하기 위해 현장에서 지표 한계침투속도와 투수속도를 측정하였으며 이 자료를 확장하여 해석하기 위해 입자특성을 이용한 Pedo Transfer Function을 개발하였다. 토심 50 cm 포화시 토양 투수성을 한계 침투속도로 가정하였으며 50 cm 이내에 암반층과 지하수위가 존재할 경우 투수성에 관계없이 D유형으로 분류하였다. 새로운 방법으로 분류한 결과 기존의 분류와 몇가지 차이점이 발견되었다. 가장 큰 차이는 대부분의 논토양이 느린 한계침투속도의 영향으로 D유형에 속한 것이다. 산림토양과 밭토양은 기존 방법과 마찬가지로 A, B유형이 많았으며 암반층을 고려하기 전에는 기존 분류에 비해 강우 유출 가능성이 적은 쪽으로 평가되었다. 그러나 암반층이 존재하는 토양을 고려한 결과 A 또는 B 유형에 속하던 상당수의 산림토양이 새로운 분류에서 D유형으로 분류되었다. 지표 유거가 많아 배수등급이 매우양호로 분류되던 토양은 정 등(1995)의 분류와 비교하여 대부분 강우 유출 가능성이 큰 쪽으로 조정되었다. 새로운 수문학적 토양유형을 이용할 경우 낮은 토심에서 암반층이 발견되는 산림토양이 분포한 유역이나 산림, 밭 등에 식질 토양이 많이 분포하는 유역에서는 기존의 방법을 이용하는 것보다 강우 유출량이 높게 평가될 것으로 판단된다. 앞으로 강우 유출량 실측자료와의 비교를 통해 지속적인 보정을 하여야 할 것이며 특히 불투수층의 존재시 일괄적으로 D유형으로 분류된 토양의 경우 깊이에 따라 C 또는 D 유형으로 세분하여 조정할 필요가 있다.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.12
• /
• pp.5-15
• /
• 2011

Conventional designs of landfill covers use geosynthetics such as geomembrane and GCL, and clay liners to lower the permeability of final covers of landfill sites. However, differential settlement and the variation of temperature or humidity in landfill sites cause the development of cracks or structural damage inside the final cover. This study examined the application of a Self Recovering Sustainable Liner (SRSL) as an alternative landfill final cover material. SRSL consists of double layers, which have chemicals, can generate precipitates filling the pores of the layers by chemical reaction. The interface material forms an impermeable layer and in case of internal cracks, the reactants of the two layers migrate towards the crack and heal it by forming another liner. In this study the applicability of SRSL material for landfill final cover was examined by performing flexible wall permeameter tests to prove that the hydraulic conductivity is lower than the regulations and unconfined compression tests to judge whether the strength satisfies the restriction for the landfill final cover. Furthermore, the environmental impacts on the permeability and strength were evaluated. The experimental results show that the SRSL has lower hydraulic conductivity and higher strength than the regulations and is little influenced by climatic changes such as wet/dry or freeze/thaw process.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.211-219
• /
• 2017

The spray-applied waterproofing membrane is installed on shotcrete or concrete surface to make impermeable layer with 3-5 mm thick for the purpose of waterproofing. This study aims to determine the internal structure of a spray-applied waterproofing membrane including pores by using X-ray CT technique. Before obtaining X-ray images of the membrane specimens, a waterproof performance test was performed on the membrane specimens with a water pressure of 500 kPa for 28 days. Results show that the movement of moisture is made through micropores. This is based on the fact that the large pores inside the membrane are not saturated and the degrees of saturation of the micropores are high. X-ray image is effective for determining the pore size distribution and whether the membrane with pores contains the water However, it is necessary to pay attention to the determination of water content, since water content may vary depending on the threshold value of X-ray image analysis applied to calculate the water content.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.3
• /
• pp.245-253
• /
• 2001

To investigate the effects of hydromechanical and textural characteristics of sediment deposits on the cultivation of Manila clam, Ruditapes philippinarum surface and sub-surface core sediments were collected seasonally in Gomso tidal flat. Grain size distribution were analyzed to investigate the annual variation of sediment texture. In winter unimodal distribution of grain size with the peak at $5\phi$ is dominant However, during the summer sediment texture become a little bit coarser and grain size distribution shows the peaks at $4\~5 \phi$. Optimum sediment texture for the cultivation of manila clam, R. philippinarum was found to be sandy silt in which mean Brain size was between 4 and $5 \phi$ with the sand content less than $50\%$ and clay content of $5\~10\%$. Mechanical and hydrological characteristics of sediment deposits were also studied in the laboratory and the results were applied to the numerical simulation for the behavior of surface sediment subjected to the cyclic loading from sea-water level change. Results of numerical simulation illustrate that the permeability of sediment had to be maintained in the range of $10^{-11}\sim10^{-12}m^2$ to ensure the proper sedimentological environment for the cultivation of manila clam, R. philippinarum. The deposits of virtually impermeable mud layer, with the threshold thickness of 4 cm, would be very hazardous to clam habitat.

• Journal of health informatics and statistics
• /
• v.42 no.4
• /
• pp.309-316
• /
• 2017

Objectives: Radon and its progeny pose environmental risks as a carcinogen, especially to the lungs. Investigating factors affecting indoor radon concentrations and models thereof are needed to prevent exposure to radon and to reduce indoor radon concentrations. The purpose of this study was to identify factors affecting indoor radon concentration and to construct a comprehensive model thereof. Methods: Questionnaires were administered to obtain data on residential environments, including building materials and life style. Decision tree and structural equation modeling were applied to predict residences at risk for higher radon concentrations and to develop the comprehensive model. Results: Greenery ratio, impermeable layer ratio, residence at ground level, daily ventilation, long-term heating, crack around the measuring device, and bedroom were significantly shown to be predictive factors of higher indoor radon concentrations. Daily ventilation reduced the probability of homes having indoor radon concentrations ${\geq}200Bq/m^3$ by 11.6%. Meanwhile, a greenery ratio ${\geq}65%$ without daily ventilation increased this probability by 15.3% compared to daily ventilation. The constructed model indicated greenery ratio and ventilation rate directly affecting indoor radon concentrations. Conclusions: Our model highlights the combined influences of geographical properties, groundwater, and lifestyle factors of an individual resident on indoor radon concentrations in Korea.

• Journal of Korea Water Resources Association
• /
• v.52 no.1
• /
• pp.35-49
• /
• 2019

This study proposes a new method for categorizing the hydrological soil groups by considering the recent revision results of soil series. Also, the proposed method is evaluated by comparing the categorizing result with those based on existing three different methods. As an example, the proposed method is applied to Jeju Island to estimate the CN value, which is then compared with CN values estimated by applying the existing three different methods. Summaries of the results are as follow. (1) The revision result since 2007 shows that the soil texture has been changed in the 43 soil series, the drainage class in the 1 soil series, the permeability in the 15 soil series, and the impermeable layer in the 26 soil series. (2) The categorizing result of hydrological soil groups by applying the proposed method shows that the group B is the most dominant group covering up to 49.25%. On the other hand, one of the existing method of 1987 provides the group C as the most dominant group (46.43%). Method of 1995 defines the group B as the most dominant group (27.69%). The other method of 2007 distinguishes the group D (35.82%) to be the most dominant group. (3) Also, the CN value estimated by applying the proposed method to Jeju Island is found to be smaller than those based on existing three methods. This result indicates the possible overestimation of the CN value when applying the existing three methods.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.121-131
• /
• 2008

In constructing a slurry trench cutoff wall, bentonite-water slurry is used to secure the stability of sidewalls during excavation before the wall is completed by backfilling. Unexpectedly, a thin but relatively impermeable layer called filter cake can be formed on the excavation surface, which significantly influences the result of slug test analysis in the cutoff wall if not considered. This study is to examine the effect of filter cake on evaluating hydraulic conductivity of the vertical cutoff wall through slug test analysis with the aid of the verified numerical program Slug_3D. The no-flux boundary conditions were adopted in Slug_3D to simulate the filter cake on the interface between the wall and the natural soil. A new set of type curves were built for applying the type curve method. New modification factors were obtained for using the modified line-fitting method. With consideration of filter cake, the type curve method and the modified line-fitting method were adopted to reanalyze the case study taken from EMCON (1995). The previous results achieved by Choi and Daniel (2006) without consideration of filter cake were compared with the present results obtained in this paper. The comparison emphasizes the necessity of considering filter cake when analyzing slug test results in vertical cutoff walls.