• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.568-572
• /
• 2000

This paper describes the experimental results of a transient impedance characteristics of grounding rods to a square pulse and standard lightning impulse current. The test were performed on single grounding rod($\phi$ 10mm, 1m) and triple-grounding rods( $\phi$ 10mm, 1m) of equilateral triangles with 5m spacing. For measurements of transient impedance, a pulse generator which can produce square wave of 30ns rise time and 20U Pulse duration was designed and fabricated. In the experiment, transient impedance of the grounding systems have been investigated from the recorded potential and current waveforms. The results showed that the value of the transient impedance is quite higher than the stationary resistance, and provide useful information for the value of a grounding system considered transient characteristics under a high frequency condition such as lightning stokes and ground-fault.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.1067-1070
• /
• 2002

We have examined the impedance characteristics and the battery characteristics of PLI bicell. As results, the impedance of PLI bicell with 62 wt% cathode active material were lower than the other cathode active material content. And the specific resistances of PLI bicell increased with N/P ratio until 1.85. And the impedance of PLI bicell decreased with increased adding amounts of binder. But the rate capability of PLI bicell were not increased with increased adding amounts of binder. PLI bicell with 9.9 wt% binder content were the best rate capability. but the cycleability were not the same results as the rate capability. PLI bicells with cathode with more than 11 wt% binder, their cycleability were almost same, nevertheless they were better cycleability than 9.9 wt% binderl content.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.351-356
• /
• 2000

Impedance is an inherent property that represents the relation between the excitation and motion of a system. It is not only gives the frequency characteristics of the system but also help us to understand an interaction with the other systems. If the impedance to be described is not with respect to a point but to a certain area, modal impedance must be used. However, it is highly dependent on modal functions and it is needed to know all information on the modal impedance to understand the whole characteristics. In this paper, two new types of impedances are introduced: the first and second kinds of total impedances. Their definitions certainly convey the implication that their properties are similar to the conventional impedance. With some limit checks and the simulations of several simple systems, we found that they are useful to describe the frequency characteristics of systems.

• Journal of Radiation Protection and Research
• /
• v.38 no.4
• /
• pp.202-207
• /
• 2013

Bioimpedance involves a lot of information related to living tissue. If there is alteration in bio tissue, its electrical characteristics also change. It is to study electrical characteristics of pork tenderlion in using a HP-4194A Impedance/Gain-phase analyzer instrument and electrical characteristics changes by graded radiation exposure dose. The results were as follow 1. Electrical characteristics of pork tenderlion in repeated measurement had high precision within ${\pm}5$% of coefficiency of variability. 2. During the measurement impedance absolute value and phase alteration did not show statistically significant difference.(p>0.05) 3. While impedance phase of electrical characteristics associated with frequency change was almost stable, impedance absolute value was in inverse proportion to frequency that means high inverse correlation of -0.096(r). 4. Impedance absolute value dropped in radiation exposure dose. The alteration of the value did not show statistically significant difference in 1 Gy, 2 Gy and 4 Gy.(p>0.05) However in radiation exposure dose of 10 Gy, the decrease of impedance absolute value was significantly different.(p<0.05) 5. Impedance phase according to radiation exposure dose change did not show statistically significant difference in 1 Gy, 2 Gy, 4 Gy, and 10 Gy(p>0.05).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.5
• /
• pp.372-376
• /
• 2012

This study focused on the performance characteristics of solar cell using the impedance technique. We measured an impedance according to frequency from 1 Hz until 1 MHz. It could know that the impedance was decreased according to the frequency increases in solar cell. The impedance of single crystal solar cell was 0.61 ${\Omega}$ at 1 Hz, and kept almost settled value to $1{\times}10^2$ Hz. However, the impedance of polycrystal solar cell was $7{\times}10^3{\Omega}$ at 1 Hz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.6
• /
• pp.1103-1108
• /
• 2010

A grounding electrode has the transient grounding impedance characteristics against lightning surges. So the performance of grounding electrodes should be evaluated as a grounding impedance as well as the ground resistance. The frequency-dependent grounding impedance is varied with the shape and size of grounding electrode and is divided into both inductive and capacitive behaviors. This paper presents a theoretical analysis for the grounding impedance determined by the size of grounding electrode using the distributed parameter circuit model. EMTP and Matlab programs were used in calculating the frequency-dependent grounding impedances of vertical grounding electrodes. It was found that the frequency-dependent grounding characteristics of vertical grounding electrodes are characterized by the distributed parameters which are changed in the dimension of grounding electrodes.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.5
• /
• pp.612-619
• /
• 2013

This paper proposes an early diagnosis technique for the stator-turn fault (STF) in an interior permanent magnet (IPM)-type brushless DC (BLDC) motor using the impedance parameter. We have analyzed the varying characteristics owing to the STF through various experiments and the finite element method (FEM). As a result, we have presented a simple method for fault detection. This technique can be applied without requiring a fast Fourier transform (FFT) and the calculation of the negative-sequence impedance. The fault detection system works on the basis of the comparison the measured impedance with the database impedance. The variations in the characteristics owing to the STF as well as the proposed technique have been verified through the simulation and experiment.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.2E
• /
• pp.46-50
• /
• 2001

The characteristics of radiation impedance are analyzed by algorithms which consists of Finite Element Method (FEM) and Hybrid type Infinite Element Method. The changes of radiation impedance for piston source according to the size and the material properties of baffles are studied. The results of the radiation impedance for rigid finite baffle coincide with other reports. The more the material properties of baffle that comes across the acoustic medium, the more the calculation results of radiation impedance approach the ones without baffle. Therefore, these results can be applied to the design and the radiation characteristics analysis of acoustic transducers.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1617-1618
• /
• 2015

This paper analyzed catenary impedance characteristics of relays installed in substation and sectioning post to protect power feeding circuit in the extended power feeding conditions. For this, we modelled AT feeding system using PSCAD/EMTDC and calculated catenary impedance. The relay installed in substation calculated catenary impedance of the extended power feeding area adding catenary impedance of self protection zone. But, the relay installed in sectioning post calculated catenary impedance of the only protection area. Therefore, we confirmed that the more reliable protection way can be utilized using the relay installed in sectioning post.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.560-563
• /
• 1997

The conventional impedance control has been known to have the following problems: it has lack of specifying force directly and unknown environment stiffness has to be known priori in order to specify the reference trajectory. In this paper, new impedance force control that can control a desired force directly under unknown stiffness is proposed. A new nonlinear impedance function is developed based on estimation of unknown stiffness from force and position measurements. The nonlinear characteristics of the proposed impedance function are analyzed based on unknown environment position. Simulation studies with robot manipulator are carried out to test analytical results.