• 대한안전경영과학회지
• /
• 제5권1호
• /
• pp.129-141
• /
• 2003

In this thesis, using the 400 series ferrite stainless steel such as 434LD$_2$ which are furter excellent then the existing ferric products in mechanical characteristics, and experiment has been conducted on corrosion resistance of sensor ring. The results are following. 1. The products before sintering are much more corrodible in the condition of spray test of salt water and ammonia than humidity and nitrogen condition. 2. 434LD$_2$ ferrite stainless steel has shown a good corrosion resistance without an addition surface treatment. thus the decreasing production process has been obtained. 3. As hardness value of $H_{RB}$ 80 and tensile test, 434LD$_2$ ferrite stainless steel with show a good endurance when it is combined to constant velocity joint (c/v joint), and has a good hardness properties endurable to sand and pebble impact.

• 한국안전학회지
• /
• 제14권1호
• /
• pp.108-115
• /
• 1999

It has been recognized that the mechanical properties of structural steels can be accepted very greatly in a state of normal temperature. While, under low temperature conditions the properties of the structural steels may not be appropriately achieved. When the various and particular structures will be constructed in an intense cold region afterward, the mechanical properties of a stainless steel under low temperature condition must be investigated. The purpose of this paper is to account for the fracture mechanics of structures in the state of low temperatures. The fracture toughness was examined through an experimental test from which the tensile strength and impact values of STS 304 were obtained. In order to demonstrate the present studies, the fracture toughness was compared with the test results for SWS 50 published previously by an author.

• 한국안전학회지
• /
• 제18권2호
• /
• pp.56-63
• /
• 2003

Flame retardancy and mechanical properties of recycled polyolefinic plastics/inorganic filler composite systems were investigated by using several inorganic flame retardants such as magnesium hydroxide and slag powder generated electro arc furnace Compatibilizer user each maleic anhydride functionalized polyethylene (PE-g-MAH) and polypropylene(PP-g-MAH) or used mixture of these. The effect of polymeric compatibilizers on the properties of composites was studied by tensile and impact test, differential scanning calorimetry, in the changed fracture mechanism. The improved adhesion was particularly reflected in the mechanical properties. The flame retardancy of composites was examined by measuring limiting oxygen index(LOI, ASTM D2863), smoke density(ASTM D2843) and vertical burning test(UL94). Regarding the flame retardant effect, the EAF slag powder is behaving as synergists as they are only active in the presence of magnesium hydroxide.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.42-46
• /
• 2023

Currently, fossil resources are depleting rapidly. We are looking for energy to replace fossil fuels. They are trying to use electricity to replace internal combustion locomotives. Secondary battery raw materials and chemical additives are pulverized by the high-speed rotation of the grinding disc of the Classifier Separator Mill. Grinding Disc Assembly requires characteristics to withstand abrasion, corrosion, high-speed rotational force and impact. Domestic and foreign grinding discs were analyzed through abrasion resistance, hardness, bending strength, and tensile adhesion strength tests.

• 대한조선학회논문집
• /
• 제59권4호
• /
• pp.207-213
• /
• 2022

LNG CCS which is a special type of cargo hold operated at -163℃ for transporting liquefied LNG is composed of a primary barrier, plywood, insulation panel, secondary barrier, and mastic. Currently, glass fiber is used to reinforce polyurethane foam. In this paper, we evaluated the possibility of replacing glass fiber-reinforced polyurethane foam with basalt fiber-reinforced polyurethane foam. We conducted a thermal conductivity test to confirm thermal performance at room temperature. To evaluate the mechanical properties between basalt and glass-fiber-reinforced polyurethane foam which is fiber content of 5 wt% and 10 wt%, tensile and an impact test was performed repeatedly. All of the tests were performed at room temperature and cryogenic temperature(-163℃) in consideration of the temperature gradient in the LNG CCS. As a result of the thermal conductivity test, the insulating performance of glass fiber reinforced polyurethane foam and basalt fiber reinforced polyurethane foam presented similar results. The tensile test results represent that the strength of basalt fiber-reinforced polyurethane foam is superior to glass fiber at room temperature, and there is a clear difference. However, the strength is similar to each other at cryogenic temperatures. In the impact test, the strength of PUR-B5 is the highest, but in common, the strength decreases as the weight ratio of the two fibers increases. In conclusion, basalt fiber-reinforced polyurethane foam has sufficient potential to replace glass fiber-reinforced polyurethane foam.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권9호
• /
• pp.774-779
• /
• 2016

본 연구에서는 선박의 곡 외판 구조에 TMCP 강재의 사용 범위 확대 가능성을 연구하고자 노말라이징강 및 TMCP 강 DH32 재질 강재에 선상가열 후 기계적 물성 시험을 실시하여 DNV 선급 및 IACS 규정의 품질 요구 기준에 적합한지 연구하였다. TMCP강재 인장시험에서 요구기준 YS = 315 MPa 대비 385 Mpa로서 약 18% 높게 나타났고, TS = 440 ~ 570 MPa 기준 대비 525 MPa로 요구 기준에 적합하였다. 샤르피 V-노치 $-20^{\circ}C$ 충격시험에서도 요구 기준에 적합하였으며 경도시험에서 평균 T : 216, L : 275로서 규정인 Hv10 = 130 ~320 범위에 만족 하였다.

• 한국주조공학회지
• /
• 제11권4호
• /
• pp.331-337
• /
• 1991

Various test specimens were prepared by austempering low alloyed Mo-Ni-Cu ductile iron blocks of high graphite nodule count at 270, 320 or $370^{\circ}C$ for 0.5, 1, 3 or 9hrs. Tensile test, CVN impact test and plane-strain fracture toughness test(compact tension specimen of 50mm W) were done for each heat treatment condition at room temperature. X-ray diffractometer and optical microscope were used to investigate the change of microstructure and relationships between microstructure and test results. The highest retained austenite volume percent at each austempering temperature was corresponded to the highest mechanical property. The highest elongation value of 17%, U.T.S. value of 1,600 MPa or $K_{IC}$ value of 90MPa${\surd}$m were reached at each optimum condition. The best heat treatment condition for fracture toughness were 3hrs' holding time combined with the austempering temperature of 270 and $320^{\circ}C$, and 1hr's of $370^{\circ}C$.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.96-101
• /
• 2004

Conventionally, SMAW process was applied to join pipes of RCL, which caused lot of loss in time and cost due to excessive heat input and defects in joining section. Recently, narrow-gap welding(NGW) process was introduced to overcome the disadvantages of SMAW. However, the application of NGW to nuclear power plant is not yet common because safety of NGW process is not proven. In present paper, the welded coupons are made of carbon steel. They are manufactured under different processes; general welding(GW), post-weld heat treatment(PWHT) after GW, repair welding after GW and PWHT with repair welding after GW in carbon steel. Performed are various mechanical tests investigation of microstructure, hardness test, tensile test at room and high temperature, bending test, impact test and J-R test. It is verified that the mechanical properties of carbon steel are greatly changed after repair welding process due to applied heat flux, and that the effect of PWHT is beneficial.

• 콘크리트학회논문집
• /
• 제24권4호
• /
• pp.369-379
• /
• 2012

비산물체의 충돌 및 폭발, 테러 등의 극한하중에 의한 구조물의 붕괴는 재산상의 손실뿐만 아니라 다수의 인명피해를 유발한다. 일반적으로 콘크리트는 타 건설재료에 비해 충격 및 폭발 하중에 우수한 저항성능을 지니고 있다고 알려져 있으나, 준-정적(quasi-static)하중과는 달리 높은 변형률 속도를 갖는 극한하중을 고려하지 않고 설계된 기존의 콘크리트 구조물은 예상치 못한 극한하중에 노출될 경우 상당히 위험할 수 있다. 이 연구에서는 콘크리트 보의 충격저항성능을 향상시키기 위해 길이 30 mm의 번들형 양단 hooked type의 강섬유를 전체 부피의 0%에서 1.5%까지 혼입하여 정하중 및 충격하중 휨 실험을 수행하고, 그 성능을 평가하였다. 실험 결과 강섬유의 혼입률을 증가시킬 경우 정하중뿐만 아니라 충격하중에서도 휨강도와 연성 등 휨 저항성능이 크게 향상되는 경향을 보였다. 강섬유를 인장부에 집중적으로 혼입한 층 구조 콘크리트 보의 경우에는 동일한 양의 섬유를 보 전체에 타설한 시편에 비해 휨 저항성능이 향상되는 것으로 나타났다. 또한, 강섬유 보강 콘크리트의 재료적 비선형성을 고려하여 단자유도계(sing degree of freedom, SDOF) 시스템의 해석 알고리즘을 구성하고 실험 결과와 비교하였으며, 비교적 정확하게 최대 처짐을 예측하는 것으로 나타났다.

• Composites Research
• /
• 제29권2호
• /
• pp.60-65
• /
• 2016

본 연구에서는 Type IV 수소 압력용기 시제품의 충격하중 조건에 따른 구조 건전성을 분석하고자 유한요소해석과 FBG 센서 삽입을 통한 실시간 모니터링 실험을 수행하여 결과를 분석하였다. 플라이 모델링 기법을 활용한 유한요소해석을 통해 FBG 센서를 삽입할 수소 압력용기의 취약부 선정 및 가압 조건을 제시하였으며, 실험을 진행할 기초 정보를 확보하였다. 실제 용기제작에 앞서 시편 실험을 통해 FBG 센서의 삽입방식 신뢰성을 확보하였으며, 이후 해당 결과를 활용하여 필라멘트 와인딩 공정에 적용하였다. 비충격 가압 피로실험과 총 4회의 충격 피로실험을 수행하였다. 실험결과 비충격 가압 피로실험에서는 해석과 동일한 거동을 보였으며, 4회의 충격 피로실험에서는 용기의 충전 시간이 점진적으로 증가하고 충전률은 감소하는 것을 확인하였다.