• Journal of Mechanical Science and Technology
• /
• 제19권6호
• /
• pp.1243-1252
• /
• 2005

This paper describes a new digital signal processor (DSP) imbalance measurement system dedicated to real-time vibration analysis on rotating machine. To accomplish real-time analysis, the vibration signals are on-line acquired and processed to analyze the mass imbalance and phase position. This is achieved through the use of FFT and Lissajous diagram. The method followed to analyze the mass imbalance with the chosen hardware and software solutions are described in detail in this paper. Several experimental tests demonstrate the efficiency and accuracy in imbalance analysis performance of the DSP system.

• 한국소음진동공학회논문집
• /
• 제21권9호
• /
• pp.828-833
• /
• 2011

A reaction wheel assembly(RWA) is the largest disturbance source that can induce high frequency micro-vibration on an optical payload of satellites. To ensure a tight pointing-stability budget of satellites, the RWA disturbance effect on spacecraft should be accurately analyzed and evaluated for whole design phases. For this purpose, the micro-vibration disturbance of RWA should be precisely measured. In the present study, two measurement methods on RWA micro-vibration disturbances are compared and investigated. One is a free run-down speed test and the other is a constant speed test. The micro-vibration data measured by the two methods are analyzed in terms of spectrum characteristics, static and dynamic imbalance values, and root sum square(RSS) values. The analysis results show that both methods can measure very similar results in time and frequency domains and that the free run-down speed method is more adequate in respects to wheel friction modeling, noise rejection of imbalance and RSS peak evaluation.

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.377-382
• /
• 2016

In this paper, influence of vibration on cogging torque and Radial Magnetic Force(RMF) imbalance was investigated in the IPM type BLDC motor. Design of cogging torque reduction and the RMF equilibrium was proceed applied to Design of Experiment(DOE). Vibration test results, the RMF imbalance was confirmed that a significant impact of vibration.

• 한국정밀공학회지
• /
• 제30권10호
• /
• pp.1095-1101
• /
• 2013

The purpose of this study was to verify the effect on improvement of muscle strength unbalance according to load deviation protocol during whole body vibration exercise. Seventeen female volunteers (age $22{\pm}3$ years, height $160{\pm}4.9$ cm, weight $49{\pm}.8$ kg) participated in this experiment. The subjects performed squat exercise in WBV platform. Exercise were performed five set a day including 15 time a set, three days a week, and during 4 weeks. Vibration stimulus was 25Hz as frequency and intensity was dominant leg 1mm and non-dominant leg 4mm. The results in WBV group showed that the differences of peak torque in 16% were getting decreasing significantly after 4 weeks from 16.2% to 5.2%. This result means that WBV with load deviation protocol could provide muscle strength exercise for muscle strength balance. Our study found out that WBV of load deviation protocol could provide muscle strength exercise for improving muscle imbalance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.843-847
• /
• 2007

The unbalanced mass of a high precision rotor deteriorates mechanical performance of the rotor. The geometrical center of a rotor generally corresponds to the rotational axis of the rotor. However, this alignment carried out with a stationary rotor does not guarantee the dynamic rotor balance. There have been a number of schemes for the correction of the imbalance published for decades especially in the hard drive industry where the issues are directly affecting manufacturing costs and product performances. Realizing the significance of the problem, the present work tries to refine one of the methods that works by applying external impact during a rotor spins. A systematic way to apply the external impact to a rotating rotor has been introduced to minimize imbalance correction process time.

• 국제물리치료학회지
• /
• 제11권4호
• /
• pp.2184-2190
• /
• 2020

Background: Although studies have been conducted on muscle thickness and balance in trunk stabilization exercise and exercise using vibration props, studies on trunk stabilization exercise using active vibration for spinal alignment are still insufficient to draw a conclusion. Objectives: To investigate the effect of trunk stabilization exercise using active vibration on the spinal alignment in adult females. Design: A randomized controlled trial. Methods: Twenty-six adult females were randomly assigned to the experimental group (active vibration) and 13 control groups (active non-vibrating) and exercised three times a week for 8 weeks. Each group was measured for spinal alignment before exercise and 8 weeks after exercise. Spinal alignment, trunk imbalance, pelvic tilt, and pelvic torsion were measured using a spinal alignment analyzer. Results: Trunk imbalance was a significantly different depending on the time in the experimental group and the control group (P<.05). Pelvic tilt was a significant difference between the groups (P<.05). Also, pelvic tilt was a significantly different depending on the time in the experimental group (P<.05), but the control group showed no significant difference (P>.05). Pelvic torsion was no significant difference in both groups (P>.05). Conclusion: This study demonstrates that trunk stabilization exercise using active vibration has a positive effect on the alignment of the spine.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.862-862
• /
• 2007

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.331-332
• /
• 2011

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.8-14
• /
• 2001

We develop a method to analyze dynamic behavior off multi-stage gear train system. The example system consists of three shafts supported by ball bearings at the ends of them and two pairs of spur gear set. For exact analysis, the meshing tooth pair of gear set is modeled as spring and damper having time-dependent meshing stiffness and damping. The bearing is modeled as spring. The result of this analysis is compared to that of other model having mean mesh stiffness. The effect of the excitation force by the unbalance off rotor off motor is also analyzed. Finally, the change ova natural frequency of the whole system due to the change of an angle between three shafts is compared in each case, and from this analysis, the avoiding angle for design is advised.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.454-461
• /
• 2001

Acoustic noise and vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and electromagnetic origins through the motor air-gap. When a relative misalignment of rotor in the air-gap center exists on the assemblage, it is considered to influence the motor system characteristics. In this paper, the back electro motive force(BEMF) is analyzed by Finite Element Method(FEM) and verified by experiments for the SPM and IPM type motors. For magnetic field analysis, a FEM is used to account for the magnetic saturation. Using these results, the FEM is made to determine the appropriate electromagnetic field analysis in BLDC motors with rotor eccentricity ratio. A radial magnetic imbalance force of BLDC motor with rotor eccentricity is analyzed. Results demonstrate that the imbalance force is increased according to the degree of misalignment. An IPM motor, mostly chosen to realize high-speed operation, shows a worse effect on magnetic unbalanced forces and dynamic responses compared with SPM motor due to magnetic saturation when the rotor eccentricity exists.