• 한국의류산업학회지
• /
• 제24권1호
• /
• pp.138-145
• /
• 2022

Today, graphene loaded textiles are being considered promising smart clothing due to their high conductivity. In this study, we reported reduced graphene oxide(r-GO) deposited pure cotton fabrics fabricated with a colloidal solution of graphene(GO), using a one-step aerosol spray pyrolysis(ASP) process and their potential application on smart textiles. The ASP process is advantageous in that it is easily implementable and can be applied for continuous processing. Moreover, this process has never been applied to deposit r-GO on pure cotton fabric. The field emission-scanning microscopy (FE-SEM) observation, Fourier transform-infrared(FT-IR) analysis, Raman spectroscopy, X-ray diffraction(XRD) analysis, and ultraviolet transmittance(UVT) were used to evaluate material properties of the r-GO colloids. The resistance was also measured to evaluate the electrical conductivity of the specimens. The results revealed that the r-GO was successfully deposed on specimens, and the specimen with the highest electrical conductivity demonstrated an electrical resistance value of 2.27 kΩ/sq. Taken together, the results revealed that the ASP method demonstrated a high potential for effective deposition of r-GO on cotton fabric specimens and is a prospect for the development of conductive cotton-based smart clothing. Therefore, this study is also meaningful in that the ASP process can be newly applied by depositing r-GO on the pure cotton fabric.

• 한국염색가공학회지
• /
• 제35권4호
• /
• pp.214-220
• /
• 2023

Poly(vinyl alcohol) (PVA) is a common hydrophilic polymer that is synthesized through the saponification reaction of poly(vinyl ester)-based polymers, mostly using poly(vinyl acetate) (PVAc) as a precursor. The heterogeneous saponification reaction of poly(vinyl ester)-based films leads to PVA films with new surface properties. Cellulose acetate (CA), in which the hydroxyl group of cellulose is replaced by an acetyl group, is a typical cellulose derivative capable of overcoming the low processability of cellulose due to strong hydrogen bonding. In this study, P(VAc/VPi)/CA blended films were prepared by the solvent casting, and then PVA/Cellulose blended films with improved surface properties were prepared by heterogeneous saponification. The structural changes caused by heterogeneous saponification were confirmed by FT-IR analysis, where both saponification and deacetylation reactions occurred in the saponification solution. In addition, the surface property changes were analyzed by FE-SEM and contact angle analyses, and the transmittance changes of the modified films were also assessed.

• 한국재료학회지
• /
• 제33권10호
• /
• pp.414-421
• /
• 2023

Infrared radiation (IR) refers to the region of the electromagnetic radiation spectrum where wavelengths range from about 700 nm to 1 mm. Any object with a temperature above absolute zero (0 K) radiates in the infrared region, and a material that transmits radiant energy in the range of 0.74 to 1.4 um is referred to as a near-infrared optical material. Germanate-based glass is attracting attention as a glass material for infrared optical lenses because of its simple manufacturing process. With the recent development of the glass molding press (GMP) process, thermal imaging cameras using oxide-based infrared lenses can be easily mass-produced, expanding their uses. To improve the mechanical and optical properties of commercial materials consisting of ternary systems, germanate-based heavy metal oxide glasses were prepared using a melt-cooling method. The fabricated samples were evaluated for thermal, structural, and optical properties using DSC, XRD, and XRF, respectively. To derive a composition with high glass stability for lens applications, ZnO and Sb₂O₃ were substituted at 0, 1, 2, 3, and 4 mol%. The glass with 1 mol% added Sb₂O₃ was confirmed to have the optimal conditions, with an optical transmittance of 80 % or more, a glass transition temperature of 660 ℃, a refractive index of 1.810, and a Vickers hardness of 558. The possibility of its application as an alternative infrared lens material to existing commercial materials capable of GMP processing was confirmed.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 춘계학술대회 논문집
• /
• pp.341-343
• /
• 2006

The current spectral shape matching method (SSMM), developed by Ahn and Shanmugam (2004), relies on the assumption that the path radiance resulting from scattered photons due to air molecules and aerosols and possibly direct-reflected light from the air-sea interface is spatially homogeneous over the sub-scene of interest, enabling the retrieval of water-leaving radiances ($L_w$) from the satellite ocean color image data. This assumption remains valid for the clear atmospheric conditions, but when the distribution of aerosol loadings varies dramatically the above postulation of spatial homogeneity will be violated. In this study, we present the second version of SSMM which will take into account the horizontal variations of aerosol loading in the correction of atmospheric effects in SeaWiFS ocean color image data. The new version includes models for the correction of the effects of aerosols and Raleigh particles and a method fur computation of diffuse transmittance ($t_{os}$) as similar to SeaWiFS. We tested this method over the different optical environments and compared its effectiveness with the results of standard atmospheric correction (SAC) algorithm (Gordon and Wang, 1994) and those from in-situ observations. Findings revealed that the SAC algorithm appeared to distort the spectral shape of water-leaving radiance spectra in suspended sediments (SS) and algal bloom dominated-areas and frequently yielded underestimated or often negative values in the lower green and blue part of the electromagnetic spectrum. Retrieval of water-leaving radiances in coastal waters with very high sediments, for instance = > 8g $m^{-3}$, was not possible with the SAC algorithm. As the current SAC algorithm does not include models for the Asian aerosols, the water-leaving radiances over the aerosol-dominated areas could not be retrieved from the image and large errors often resulted from an inappropriate extrapolation of the estimated aerosol radiance from two IR bands to visible spectrum. In contrast to the above results, the new SSMM enabled accurate retrieval of water-leaving radiances in a various range of turbid waters with SS concentrations from 1 to 100 g $m^{-3}$ that closely matched with those from the in-situ observations. Regardless of the spectral band, the RMS error deviation was minimum of 0.003 and maximum of 0.46, in contrast with those of 0.26 and 0.81, respectively, for SAC algorithm. The new SSMM also remove all aerosol effects excluding areas for which the signal-to-noise ratio is much lower than the water signal.

• 한국포장학회지
• /
• 제25권3호
• /
• pp.69-77
• /
• 2019

자몽씨추출물(GSE)과 ZnONP을 아가필름에 동시에 첨가하여 다기능성 복합필름을제조하였다. Agar/GSE/ZnONP복합필름은 특히 자외선차단성과 항균성에 대한 시너지 효과를 나타냈다. 광 차단성은 자외선 파장범위인 280 nm와 가시광선 파장범위인 660 nm에서 유의적인 차이를 보이며 크게 나타났다. 자외선차단성은 agar/GSE와 agar/ZnONP 필름에 비해 agar/ZnONP^3%/GSE^5% 필름에서의 크게 상승하여 GSE와 ZnONP의 시너지 효과를 확인할 수 있었다. 항균성으로는 그람양성균인 L. monocytogenes와 그람음성균인 E. coli O157: H7 모두 agar/ZnONP^3%/GSE^5% 필름에서 강한 항균성 및 시너지 효과가 있었다. 자외선 차단성과 항균성은 포장식품의 안전성을 확보하고 유통기한을 연장시키는데 필수적인 특성으로 agar/ZnONP3%/GSE5% 필름은 식품의 유통기한 연장과 식품의 안전성을 위한 포장필름으로 활용 가치가 높을 것으로 사료된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.77-77
• /
• 2000

Titanium oxide (TiO2) thin films have valuable properties such as a high refractive index, excellent transmittance in the visible and near-IR frequency, and high chemical stability. Therefore it is extensively used in anti-reflection coating, sensor, and photocatalysis as electrical and optical applications. Specially, TiO2 have a high dielectric constant of 180 along the c axis and 90 along the a axis, so it is highlighted in fabricating dielectric capacitors in micro electronic devices. A variety of methods have been used to produce patterned self-assembled monolayers (SAMs), including microcontact printing ($\mu$CP), UV-photolithotgraphy, e-beam lithography, scanned-probe based micro-machining, and atom-lithography. Above all, thin film fabrication on $\mu$CP modified surface is a potentially low-cost, high-throughput method, because it does not require expensive photolithographic equipment, and it produce micrometer scale patterns in thin film materials. The patterned SAMs were used as thin resists, to transfer patterns onto thin films either by chemical etching or by selective deposition. In this study, we deposited TiO2 thin films on Si (1000 substrateds using titanium (IV) isopropoxide ([Ti(O(C3H7)4)] ; TIP as a single molecular precursor at deposition temperature in the range of 300-$700^{\circ}C$ without any carrier and bubbler gas. Crack-free, highly oriented TiO2 polycrystalline thin films with anatase phase and stoichimetric ratio of Ti and O were successfully deposited on Si(100) at temperature as low as 50$0^{\circ}C$. XRD and TED data showed that below 50$0^{\circ}C$, the TiO2 thin films were dominantly grown on Si(100) surfaces in the [211] direction, whereas with increasing the deposition temperature to $700^{\circ}C$, the main films growth direction was changed to be [200]. Two distinct growth behaviors were observed from the Arhenius plots. In addition to deposition of THe TiO2 thin films on Si(100) substrates, patterning of TiO2 thin films was also performed at grown temperature in the range of 300-50$0^{\circ}C$ by MOCVD onto the Si(100) substrates of which surface was modified by organic thin film template. The organic thin film of SAm is obtained by the $\mu$CP method. Alpha-step profile and optical microscope images showed that the boundaries between SAMs areas and selectively deposited TiO2 thin film areas are very definite and sharp. Capacitance - Voltage measurements made on TiO2 films gave a dielectric constant of 29, suggesting a possibility of electronic material applications.

• 한국진공학회지
• /
• 제6권4호
• /
• pp.348-353
• /
• 1997

DC saddle-field plasma enhanced chemical vapor deposition(PECVD) 장치를 이용 하여 상온에서 p-type Si(100) 기판위에 hydrogenated amorphous carbon(a-C:H) 박막을 증 착하고 기판의 bias 전압 변화에 따른 박막의 미세구조 변화와 광학적 특성을 연구하였다. 본 실험시 CH4 가스의 유량은 5sccm, 진공조의 $CH_4$ 가스압력은 90mtorr로 일정하게 유지 하였으며 기판의 bias 전압($V_s$)은 0V에서 400V까지 변화시켰다. Rutherford backscattering spectroscopy(RBS)와 elastic recoil detection(ERD) 측정결과 증착된 a-C:H박막의 증착율은 $V_s$=0V에서 $V_s$=400V로 증가함에 따라 45$\AA$/min에서 5$\AA$/min으로 크게 감소하였지만 박막 내의 수소 함유량은 15%에서 52%까지 크게 증가하였다. a-C:H박막내의 수소 함유량이 증 가함에 따라 a-C:H박막은 sp3CH3구조의 polymer like carbon(PLC) 구조로 변환되는 것을 FT-IR로 확인하였으며 Raman 측정 결과 $V_s$=100V와 $V_s$=200V에서 증착한 a-C:H 박막에서 만 C-C결합에 의한 disorder 및 graphite peak를 볼 수 있었다. Photoluminescence(PL) 측 정 결과 $V_s$=200V까지는 기판의 bias 전압이 증가함에 따라 PL세기는 증가하였으나 그 이 상의 인가전압에서는 PL세기가 점점 감소하였다. 특히 $V_s$=200V에서 제작한 a-C:H박막의 PL특성은 상온에서도 눈으로 보일 만큼 우수한 발광 특성을 보였으며, 기판 bias전압이 증 가함에 따라 PL peak 위치가 청색으로 편이하는 경향을 보였다. 이러한 발광 세기의 변화 는 $V_s$=0V부터 $V_s$=200V까지는 기판의 bias전압이 증가함에 따라 상대적으로 박막의 표면에 충돌하는 이온에너지의 감소로 인해 a-C:H박막내에 비발광 중심으로 작용하는 dangling bond가 감소하여 발광의 세기가 증가하였으며 $V_s$=300V이상에서는 박막내의 수소 함유량이 증가함에 따라 dangling bond수는 감소하나 발광 중심으로 작용하는 탄소간의 $\pi$결합을 포 함하는 cluster가 줄어들어 PL세기가 감소한 것으로 생각된다.