• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.348-348
• /
• 2010

Behaviors of $TiO_2$-based photocatalysts with different surface structures on the removal of gas-phase toluene with and without UV irradiation are reported. P-25(Degussa) $TiO_2$ powder dispersed in distilled water by sonication was deposited on the transparent glasses and then dried. Some of the samples were further annealed in oven for 1 hr. These samples obtained before and after annealing were characterized by Brunauer- Emmett-Teller (BET), Transmission Electron Microscope (TEM), X-ray Photoelectron Spectroscopy (XPS) and Fourier Transform Infrared (FT-IR) spectrometry, respectively. Based on BET and TEM data, no significant structural change upon annealing could be identified. However, the sample without annealing showed a significantly higher ability for removing toluene both in the presence and absence of the UV light. XPS and FT-IR results clearly revealed that the population of the OH groups on the surface of $TiO_2$ was higher for the sample without annealing, indicating that the OH groups can enhance the adsorption capacity and photocatalytic activity of $TiO_2$ for the removal of the gas-phase toluene.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2015.10a
• /
• pp.578-579
• /
• 2015

Transmission and reflectance are two non-invasive techniques to perform pulse oximetry. This paper presents a design of reflectance-based pulse oximetry for watch-type wearable device, in which sensor and detector are located on the same surface of the body part. The basic principle of a pulse oximeter is based on the measurement of the red and infrared (IR) light absorption. Oxygenated blood has significant differences of light absorption characteristics than deoxygenated blood under red (660 nm) and infrared (940 nm) wavelength. Infrared is absorbed more by oxygenated hemoglobin than red. So the hardware implementation is included placing of the two LEDs (red and IR) with single photo-detector in the middle on the patient's wrist to get the corresponding pulsatile signals which are used to estimate the $SpO_2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.553-563
• /
• 2010

This paper presents a tapered slot-antenna(TSA) for optimal impulse-signal transmission in ultra-wide band(UWB). The proposed TSA provides radiates in end-fire direction, which meets an impulse-radio UWB(IR-UWB) system demands(e.g., low loss, thus less error throughout the UWB band). In order to minimize the pulse distortion, we used an wideband impedance transformer and a microstrip slotline. The pulse fidelity characteristics was evaluated with finite-difference time-domain(FDTD) analysis technique and pulse fidelity correlation equation. Approximately 93.89 % pulse fidelity was obtained between the two antennas in 0.5 m range. Additionally, derived chirp Z-transform algorithm enables us to utilize the zoom-in option on the pulse signal in few nano-seconds below. Thus, it is possible to analyze the pulse signal distortion, delay or dispersion characteristics.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.28-28
• /
• 2018

수전해(electrochemical water splitting)는 연료전지의 가역적 역반응을 이용하여 물로부터 수소와 산소를 발생시키는 기술이다. 산소는 음극에서 발생하는데, 이 때 음극 표면은 고농도의 산소 음이온 및 라디칼에 장시간 노출된다. 때문에 기계적, 화학적 내구성이 우수한 전극재를 사용할 필요가 있다. 불용성 전극 (dimensionally stable anode, DSA)은 이러한 기술적 요구사항을 잘 만족하는 상용화 된 전극이다. 티타늄이나 티타늄 합금 표면에 촉매를 미량 반복 살포하여 산화물 형태의 매우 견고한 표면을 형성함으로서 내구성을 확보한다. 그러나, 보통 DSA 제조 기법의 특징에 따라 다공성 표면 구조를 사용하지는 않기 때문에 생산 과정이 복잡하고 비용이 많이 발생하는 문제를 여전히 나타내고 있다. 본 연구는 상기 문제를 개선하기 위한 수전해용 음극 제조 기술에 관한 연구이다. 티타늄과 티타늄 합금은 동일한 양극산화 기술 적용이 가능하다는 점을 이용하여 티타늄 기판으로부터 다공성 구조를 형성함으로써 바인더의 사용을 배제하였다. 단일공정양극산화기법 (single-step anodization)을 이용하여 $IrO_2$와 $RuO_2$를 도핑함으로써 TiO2에 촉매능을 부여하였다. 제조된 나노튜브들의 구조적 특징을 HR-TEM (High-resolution transmission electron microscope)과 FE-SEM (Field-emission scanning electron microscope)으로 분석하고 SAED (selective area electron diffraction) 패턴을 분석하여 전극재의 결정성을 확인하였다. 알칼라인 분위기에서 일으킨 산소발생반응 (oxygen evolution reaction, OER)의 LSV (linear sweep voltammetry) 결과를 XPS (X-ray photoelectron microscoscopy) 결과와 연관지어 촉매 표면 구조와 과전압의 관계를 해석하였다. LSV 결과로부터 Tafel 분석을 연달아 수행함으로써 전극의 속도결정단계를 정의하였다. 최종적으로 사이클 테스트 통하여 DSA로써의 성능을 평가하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.7
• /
• pp.507-514
• /
• 2022

The EO/IR targeting pod mounted on a fighter to acquire information about tactical targets is typically mounted and operated at the bottom of the aircraft fuselage. Since the aircraft equipped with such an external attachment has complexed aerodynamic and inertial characteristics compared to the aircraft flying without an external attachment, a method of system performance analyses is required to identify development risk factors in the early stages of development and reflect them in the design. In this study, a development plan was presented to provide the necessary modeling and simulation tools to develop a pod that can acquire measurement data stably in a highly maneuverable environment. The limiting operating conditions of the pods mounted on the highly maneuverable aircraft were derived, the aerodynamics and inertial loads of the mounted pods were analyzed according to the limiting operating conditions, and a flight data generation and transmission system were developed by simulating the mission of the aircraft equipped with the mounted pods.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2431-2436
• /
• 2012

This paper is implemented simple visible light communication system by combining the communications through LED lighting. It uses a variable PD sensor to the receiver and 1~12 the LED light-emitting device to the transmitter to realize LED visible light communication. Initial distance value of the developed transmission and receiver is more than 0~1.5m for LED visible light communication, the overall system transmission rate is organized with thousands kbps variability visible light media transmission system. It was measured the performance experiment during lens wearing or not wearing in order to increase the overall efficiency of the LED module, configures the LED and PD to existing PC module for the performance analysis of the implemented research, experiments the maximum communication distance of the transmitter/receiver according to LED count and the transmission rate, check about application methods and the possibility.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.161-161
• /
• 2017

Seed endophytes are very remarkable groups of bacteria for their unique abilities of being vertically transmitted and conserved. As plants attain hybrid vigor and heterosis in the process of crossbreeding, this might also lead to the changes in the community structure and diversity of plant endophytes in the hybrid plants ultimately affecting the endophytes of the seeds. It would be interesting to characterize how seed endophyte composition change over time. The objective of this study is to gain insights into the influence of natural crossbreeding and parental lineage in the seed bacterial endophytic communities of two pure inbred lines exploring contributions of the two most important sources of plant endophytes - colonization from external sources and vertical transmission via seeds. Total genomic DNA was isolated from rice seeds and bacterial DNA was selectively amplified by PCR. The diversity of endophytic bacteria was studied through Terminal-Restriction Fragment Length Polymorphism (T-RFLP) analysis. Diversity between the original parents and the pure inbred line may show significant differences in terms of richness, evenness and diversity indices. Heat maps reveal astonishing contributions of both or either parents (IR29 ${\times}$ Pokkali and AT401 ${\times}$ IR31868) in the shaping of the bacterial seed endophytes of the hybrid, FL478 and IC32, respectively. Most of the T-RFs of the subsequent pure inbred line could be traced to any or both of the parents. Comparison of common and genotype-specific T-RFs of parents and their offspring reveals that majority of the T-RFs are shared suggesting higher transmission of bacterial communities common to both parents. The parents influence the bacterial community of their offspring. Unique T-RFs of the offspring also suggest external sources of colonization particularly as the seeds are cultivated in different ecogeographical locations. This study showed that host parental lines contributed greatly in the shaping of bacterial seed endophytes of their offspring. It also revealed transmission and potential conservation of core seed bacterial endophytes that generally become the dominant microbiota in the succeeding generations of plant hosts.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.394-394
• /
• 2012

We fabricated organic-inorganic superlattice films using molecular layer deposition (MLD) and atomic layer deposition (ALD). The MLD is a gas phase process in the vacuum like to atomic layer deposition (ALD) and also relies on a self-terminating surface reaction of organic precursor which results in the formation of a monolayer in each sequence. In the MLD process, 'Alucone' is very famous organic thin film fabricated using MLD. Alucone layers were grown by repeated sequential surface reactions of trimethylaluminum and ethylene glycol at substrate temperature of $80^{\circ}C$. In addition, we developed UV-assisted $Al_2O_3$ with gas diffusion barrier property better than typical $Al_2O_3$. The UV light was very effective to obtain defect-free, high quality $Al_2O_3$ thin film which is determined by water vapor transmission rate (WVTR). Ellipsometry analysis showed a self-limiting surface reaction process and linear growth of each organic, inorganic film. Composition of the organic films was confirmed by infrared (IR) spectroscopy. Ultra-violet (UV) spectroscopy was employed to measure transparency of the organic-inorganic superlattice films. WVTR is calculated by Ca test. Organic-inorganic superlattice films using UV-assisted $Al_2O_3$ and alucone have possible use in gas diffusion barrier for OLED.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1656-1661
• /
• 2012

UV inspection technology is being used for predictive maintenance of power facility together with IR-thermography and ultrasonic devices. In this paper, the UV corona camera design, fabrication, and perform a simple test to be take advantage of the diagnostic equipment. The UV corona camera developed a $6.4^{\circ}{\times}4.8^{\circ}$ of the field of view as a conventional camera to diagnose a wide range of slightly enlarged, and power equipment to measure the distance between the camera and the distance meter has been attached. The transmission between 250 to 280nm was 11% ($12.5%{\times}88%{\times}98%$) by combing the transmission on absorption film, window and other filter(UG 5, nickel sulphate and so on). In a distance of 5m with the UV corona camera it is possible to detect partial discharge with a PD level of 2.5pC and a RIV level of $3.6dB{\mu}V$.

• Korean Membrane Journal
• /
• v.8 no.1
• /
• pp.67-73
• /
• 2006

Transparent materials are well known but preparation of transparent poly 2-hydroxyethyl methacrylate {poly (HEMA)} material by varying solvent is a new one and economically reliable. This material is prepared from hydroxyl based monomer HEMA by radical polymerization using benzoyl peroxide (BPO) as initiator and isobutanol, 2-butanol, 1-butanol, hexane and toluene as a solvent. The reaction temperature, time and stirring speed were set at $70^{\circ}C$, 4 hrs and 150 rpm, respectively. The polymer was characterized for functional group by IR spectroscopy. It was observed that the intensity of band at $1637 cm^{-1}$ a characteristic band of C=C stretching disappeared indicating that it was completely consumed after polymerization. It was observed that swelling percentage increases with increase as time passes but after a certain time a constant swelling percentage is achieved. SEM pictures reveals that poly (HEMA) prepared by different solvent shows pore with a distinguishable void up to several micrometers. The BET surface area, cumulative pore volume and average pore diameter is greater in poly (HEMA) prepared by hexane as a solvent compared to other solvents. Poly (HEMA) prepared by 1-butanol as a solvent shows higher glass transition temperature compared to other solvents. Poly (HEMA) prepared by different solvents shows $90{\sim}94%$ light transmission property from light transmission measurement and looks transparent.