• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.155-159
• /
• 2004

This paper describes the design and the simulation of a single pole double throw(SPDT) FET switch for wireless LAN(IEEE802.11a ＆ IEEE802.11b) applications using drain impedance transformation network with Microstrip transmission line. At the receiving path insertion losses were from 0.8(㏈) to 1.462(㏈) between 2(㎓) and 4(㎓), from l.26(㏈) to 2.3(㏈) between 4.7(㎓) and 6.7(㎓) and the isolations were under 30(㏈) between 2(㎓) and 6.7(㎓). At the transmitting path insertion loss were from 1.18(㏈) to 2.87(㏈) between 2(㎓) and 4(㎓) from 0.625(㏈) to 1.2(㏈) between 4.7(㎓) and 6.7(㎓) and the isolations were under 30(㏈) between 2(㎓) and 6.7(㎓).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.49-56
• /
• 2006

This paper describes the design and the verification of IEEE 802.15.4 LR-WPAN 2.4GHz Physical layer for Ubiquitous Sensor Network(USN). We designed the Carrier Frequency Offset(CFO) compensation satisfied the frequency tolerance of IEEE 802.15.4 LR-WPAN and the adaptive matched filter that re-setting of the threshold for the symbol synchronization of the various USN environment. The multiplications is reduced 1/16 by this method each other at i, q phases and has 0.5dB performance improvement in detection probability. Proposed baseband system is designed with verilog HDL and implemented using FPGA prototype board.

• Journal of Sensor Science and Technology
• /
• v.18 no.3
• /
• pp.245-250
• /
• 2009

The paper presents the wireless wind chill temperature measurement system that is composed of IEEE 802.15.4 standard wireless communication devices, hot film anemometer and serial communication temperature sensor. It's sometimes very difficult for a person, who lives in a high-rise apartment, to see the outside wind chill temperature due to harsh outside weather. The wind chill temperature is calibrated from an air velocity and air temperature. IEEE 802.15.4 standard wireless communication is ZigBee compatible, and consumes low power in communication. Under the air temperature of 5 $^{\circ}C$ and air velocity ranging from 0 to 50 km/h, the experimental result of wind chill temperature shows good accuracy within 5%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.154-160
• /
• 2005

Microwave Otters are essential device in modem wireless systems. A compact dimension BPF(Band-pass Filter) for IEEE 802.11a WLAN service is realized using LTCC multi-layer process. To extrude 2-stage band-pass equivalent circuit, band-pass and J-inverter transform applied to Chebyshev low-pass prototype filter. Because parallel L-C resonator is complicate and hard to control the inductor characteristics in high frequency, the shorted $\lambda/4$ stripline is selected for the resonator structure. The passive element is located in the different layers connected by conventional via structure and isolated by inner GND. The dimension of fabricated stacked band-pass filter which is composed of six layers, is $2.51\times2.27\times1.02\;mm^3$. The measured filter characteristics show the insertion loss of -2.25 dB, half-power bandwidth of 220 MHz, attenuation at 5.7 GHz of -32.25 dB and group delay of 0.9 ns at 5.25 GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.9 s.351
• /
• pp.17-22
• /
• 2006

CMOS LC VCO with fast response adaptive frequency calibration (AFC) technique for IEEE 802.11a/b/g WLANs is designed in 1.8V $0.18{\mu}m$ CMOS process. The possible operation is verified for 5.8GHz band, 5.2GHz band, and 2.4GHz band using the switchable L-C resonators. To linearize its frequency-voltage gain (Kvco), optimized multiple MOS varactor biasing tecknique is used. In order to operate in each band frequency range with reduced VCO gain, 4-bit digitally controlled switched- capacitor bank is used and a wide-range digital logic quadricorrelator (WDLQ) is implemented for fast frequency detector.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.4A
• /
• pp.414-422
• /
• 2011

This paper describes a design of low-density parity-check(LDPC) decoder supporting block length 2,304-bit and code rate 1/2 of IEEE 802.16e mobile WiMAX standard. The designed LDPC decoder employs the min-sum algorithm and partially parallel layered-decoding architecture which processes a sub-matrix of $96{\times}96$ in parallel. By exploiting the properties of the min-sum algorithm, a new memory reduction technique is proposed, which reduces check node memory by 46% compared to conventional method. Functional verification results show that it has average bit-error-rate(BER) of $4.34{\times}10^{-5}$ for AWGN channel with Fb/No=2.1dB. Our LDPC decoder synthesized with a $0.18{\mu}m$ CMOS cell library has 174,181 gates and 52,992 bits memory, and the estimated throughput is about 417 Mbps at 100-MHz@l.8-V.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.799-804
• /
• 2008

In the paper, a dual-bandpass filter for ship's wireless LAN has proposed, which was designed by using step stub in compliance with 2.4 GHz and 5.2 GHz band The dual-bandpass filter can be designed by adjusting the sizes of the step stub in compliance with the frequency bands of 2.4 GHz and 5.2 GHz, which has the improved performance compared with the existing dual-bandpass filter. Furthermore, dual-bandpass filter using step stub has better efficiency. The measured results for the fabricated dual-bandpass filters agreed well with the simulated ones, and hence it was confirmed that the proposed design method is valid.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.265-270
• /
• 2005

In this paper, four-element MIMO(Multi-Input Multi-Output) antenna operating at 5.2GHz and 5.8GHz is proposed. Each antenna element is fabricated by using inverted-L type and the isolation characteristic among antenna elements is adjusted by the distance between radiation element and ground. The designed array antenna has the impedance bandwidth at 5.15$\sim$5.35 and 5.725$\sim$5.825GHz for VSWR$\leq$3 and the isolation characteristic less than -20dB at same frequency.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.11
• /
• pp.2442-2450
• /
• 2010

Using sensor devices applied to various objects will be needed wireless network that it is easy to install in them. Tiny devices configured to processor that bas comparatively low computing ability are inappropriate to use devices that are wireless LAN, etc. In result, network devices needed to not only have simple communication protocol, but have Plug and Play function that it works as soon as it connects without installing any device driver. it also will industrially have both low power and low cost because of mobility of it. From IEEE 802.11 standard, WPAN(Wireless Personal Area Network) included in LAN is being developed by WPAN WG(Working Group) on area with low power consumption and low complexity. In addition to, it is standardizing MAC and PRY of the standard that is expected to wirelessly communicate within 10m. WPAN will be used generally in the more near future because of both low power and low cost of Zigbee. In this paper we designed zigbee based user authentication module for a automotive smart-key system.