• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.73-79
• /
• 2008

Atomization speed of diesel fuel injected from 8-hole nozzle is faster than that of 7-hole nozzle because the hole diameter of 8-hole nozzle is smaller than that of 7-hole nozzle. But both insufficient distance between the fuel sprays and short penetration of injected sprays through 8-hole nozzle hole cause many harmful effects on combustion. In this study, we installed the 8-hole injectors to diesel 2.0 liter class engine, and optimized in-cylinder swirl and penetration via selecting and matching proper cylinder head and combustion bowl. Through this process, we found out the performance and emission potential of 8-hole nozzle installed engine are better than those of 7-hole nozzle installed one.

• International Journal of Automotive Technology
• /
• v.2 no.2
• /
• pp.63-75
• /
• 2001

This paper describes the development of THC reduction technologies compliant with SULEV regulations. Technologies embodied by the developmental work include improvement of fuel spray atomization, quick warm-up through coolant control shut of, and acceleration of fuel atomization for the fast rise of cylinder head temp inside the water jacket as well as the improvement of combustion state. The technologies likewise entail reduced HC while operating in lean A/F condition during engine warm-up with the cold lean burn technology, individual cylinder A/F control for improvement of catalytic converting efficiency, after-treatment such as thin-wall catalyst, HC-adsorber and EHC and etc, through vehicle application evaluation in cold start. We carried out an experimental as well as a practical study against SULEV regulations, and the feasibility of adopting these items in vehicle was likewise investigated.

• Corrosion Science and Technology
• /
• v.15 no.2
• /
• pp.78-83
• /
• 2016

The e-coating to inhibit induced corrosion can deposit a coating not only on the exterior surface but also on the inside of whole metallic components of body-in-white (BIW). But it is difficult to deposit paint films on the inside area because metallic components are multi layered. It may cause shortness of e-coating thickness. The only way to properly verify e-coating thickness is by performing the use of tear-down prototypes. When paint films' thickness is inadequate, a structural modification on each metallic component is needed. Verification of the thickness improvement for a structural modification requires much manual effort and leads to increasing development time. Recently, the simulation technology has been developed to predict the e-coating thickness in e-coating field. By applying the simulation to BIW, improvement in paint thickness quality and shortening of development period are expected. The paper explains a validated solution that allows simulating the effect of design changes to the e-coating thickness and current density, thereby delivering results within a time frame of a few days.

• Journal of Hydrogen and New Energy
• /
• v.22 no.5
• /
• pp.585-591
• /
• 2011

This study has focused on the development of high performance membrane-electrode assemblies (MEAs) fabricated by decal method for proton exchange membrane fuel cell (PEMFC). To study the effect of ionomer contents on performance, we fabricated MEAs with several electrodes which were prepared by varying the quantity of ionomer from 20 wt.% to 45 wt.% in catalyst layer. The MEA performance was obtained through single cell test. The MEA prepared from electrode with 25wt.% of ionomer showed the best performance. We evaluated the surface area and pore volume of electrode with BET. We found that the surface area and pore volume in electrode decreased rapidly at the electrode with 40wt.% of ionomer in catalyst layer. MEA was fabricated by roll laminator machine and the roll laminating conditions for the preparation of MEA, such as laminating press, temperature and speed, were optimized. The MEA performance is not affected by laminating temperature and speed, but roll laminating press have a great effect on MEA performance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.7
• /
• pp.669-674
• /
• 2013

To design the optimized low noise planetary gear sets, a program called pRMC(planetary run many cases) is developed. The pRMC is especially using a combination analysis method for all gear specifications and also able to analyze any type of planetary gear sets. The pRMC is composed of the 5 sections those are generate, setting, evaluate, combine and analysis. After calculating all candidate gear sets, the pRMC could show many results that represent the character of each gear set including the transmission error which is the main gear noise factor, the contact ratios, the bending stress and so on. By comparing the results objectively, user could predict and select the optimized gear set which has quiet noise level and desired durability. The planetary gear designed by pRMC could have reduced noise and vibration level from 5 to 10 dB than previous-designed one.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1045-1046
• /
• 2007

As equivalent load method of induction motor, even without connecting load, for temperature rise test has been acknowledged economic and corrective method, the method has been widely used instead of the real load method, and also international standards IEC 61986 is published in 2002. ABB, an well-known and famous electric machinery maker in the world, has been already applying the equivalent load method since 2002. HHI has been using real load method and equivalent load method for temperature rise of induction motor, it is already known that the equivalent test results is higher as $1-5^{\circ}K$ than that of real load test. But, quantity analysis for the reason of the temperature rise is not satisfied sufficiently. So, in this paper, quality analysis and also quantity analysis was conducted.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.543-547
• /
• 1991

This paper illustrates maximum torque per ampare radio operation and efficiency operation, which are prevalently applied to the control of permanent magnet synchronous motor(PMSM). Maximum torque per ampare ratio operation minimizes the copper loss of PMSM and maximum efficiency operation minimizes the total loss of PMSM. To verify the difference of these method, simulation and experiment results applied to IPMSM(Interior type PMSM) and SPMSM(Surface mounted PMSM) are presented.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.927-929
• /
• 2005

In this paper, through the theoretical study on reducing method and analysis of stray load loss of induction motor, we suggest the improved design considering the slot combination, skew, air gap and manufacturing method. For verifying the suggested design, the test was performed by IEEE 112. As a result, the reducing technology on the stray load loss was established.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.98-100
• /
• 1995

This paper deals with development of high torque and high accurate stepping motor and control system which is adopted heavy equipment engine speed control. In the process of development, only pure domestic technics is involved, all the parts are supplied in domestic industries, and successfully accomplished to mass production. In order to confirm product liability, circumferential test,such as vibration test impact test,thermal test,and field test are thoroughly fulfilled.

• Journal of Hydrogen and New Energy
• /
• v.20 no.3
• /
• pp.224-231
• /
• 2009

The improvement of cold start capability is one of the most challenging tasks to be solved for commercialization of fuel cell vehicle. In this study, cold start test and ice blocking test(IBT) of fuel cell stack were carried out under various operating conditions. This fuel cell stack can be thawed from -20$^{\circ}$C within 25s and the voltage change was found to be comprised of 4 steps; the first step is the voltage decrease by overpotential, the second step is the voltage increase by the cell temperature increase, the third step is the voltage decrease by ice blocking, and the last step is the voltage increase by thawing. Bootstrap startup was failed after shutdown at temperature under 40$^{\circ}$C because of much condensed water in the fuel cell. Quantitative estimation of cold start capability have been demonstrated by ice blocking test(IBT). In the results, it was found that cold start capability was improved double every 10$^{\circ}$C from 30$^{\circ}$C to 65$^{\circ}$C and enhanced by 30% at the condition of SR 3/4 compared to SR 1.5/2.0 and enhanced by 20% with dry purge condition compared to with RH 50% purge condition.