• Journal of Biosystems Engineering
• /
• v.16 no.1
• /
• pp.37-48
• /
• 1991

Rice plants are subjected to various forces such as natural force of wind and mechanical force of cultivating machines. Rheological behavior of the rice stem can be expressed in terms of three variables : stress, relaxation and time. The objectives of this study are to examine stress relaxation, creep and recovery characteristics on the rice stem in case of axial and radial loading. Stress relaxation with time was studied on three levels of loading rate and on four levels of applied stress. The results were summarized as follows : 1. The hysterisis losses of the rice stem distinctly observed at the radial compression in comparison with axial compression. The hysterisis loss implied that the stem to absorbed energy without being deformed beyond the yield point. 2. Ageneralized Maxwell model consisting of three elements gave a good description of the relaxation behavior of the rice stem. Rate of loading was more significant on the observed relaxation behavior within the short relaxation time, but there were little influences of rate of loading on the relaxation time. 3. The stress relaxation intensity and the residual stress increased in magnitude as the applied stress increased, but the relaxation time was little affected by the applied stress. 4. The coefficients of the stress relaxation model showed much differences in the radial compression and the axial compression, especially the higher relaxation stress of the third element was observed in the radial compression. 5. The behaviors of rice stem in creep and recovery test also might be represented by a four element Burger's model. But the coefficients of the creep model were different from those of the recovery model. 6. The steady-state phenomena of creep appeared at the stress larger than 20 MPa in Samkang and 1.8 MPa in Whajin. 7. The elastic modulus of the stem showed the range from 40 to 60 MPa. It could be considered, as a result, the rice stems had viscoelastic properties.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.98-103
• /
• 1992

The dynamic and static torque characteristics of a three dimensional control panel installed behind a guide panel were investigated in a wind tunnel. The panel was tested for various wind speeds, angles of attack and positions of the panel. The effects of the rotational speed and the amplitude of the sinusoidal motion were also studied. The increasing rate of torque coefficients with the angular position of the panel is small when the panel remains in the wake region, but is linear when it reaches the external stream. In case of a sinusoidal motion of the pannel, a hysterisis appears in the dynamic torque. The hysterisis becomes strong as the wind speed and the angular speed of the panel increase. The unsteady torque is considered quasi-steady when the angular speed is less than 5.5rad/s, i.e. the reduced frequency is less than 0.035.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.12
• /
• pp.5-11
• /
• 2010

If the groundwater in rock joint is changed into ice, it induces the stress increment by volume increase. Also, if the ice is changed into groundwater again, the stress in joint decreases by volume decrease. The accumulated displacement and fatigues of joints are increased by the stress-hysterisis, induced from the continuous frost-thawing. Also the shear strength is decreased by them continuously. The stress-hysterisis is affected by the atmospheric temperature changes, whose behavior is visco-elasticity, usually. Therefore, Kelvin model could be used to analyze the frost-thawing behavior in winter. The measured data of total 5 points are examined, which are composed of 3 points of shallow joints and 2 points of deep joints. Because shallow weathered rocks have many joints, a lot of Kelvin model are connected and the behaviors are complicated. In case of deep joints, simple Kelvin model is applied and the behaviors are also simple.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.1
• /
• pp.21-28
• /
• 2005

As the maximum power operating point(MPOP) of the Photovoltaic(PV) power systems alters with changing atmospheric conditions, the efficiency of maximum power point tracking(MPPT) is important in PV power systems. Many MPPT techniques have been considered in the past, but techniques using microprocessors with appropriate MPPT algorithms are favored because of their flexibility and compatibility with different PV arrays. In this paper, the author analyzes and studies two MPPT algorithms, which is named P&O(Perturbation and Observation) and IncCond(Incremental Conductance). Also, the author proposes Hysterisis-band alteration algorithm. To show the excellency of new Hysterisis-band alteration, the author suggests three references; 1) Comparing three MPPT algorithms in the steady-state condition, 2) Representing irradiation variation rapidly, 3) Showing MPPT efficiency. MPPT simulation and experiment perform in the boost converter.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.323-325
• /
• 1990

In this paper, a new method to track the maximum power point is presented. The proposed scheme achieves the maximum power the step-up chopper, which tracks the maximum power point by sensing only the actual current from the photovoltaic array. Also it adopts the protect ion circuit to protect the battery system against the overvoltage and overvoltage by utilizing hysterisis characteristic.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.415-419
• /
• 2003

This paper focuses on a simple technique to reduced torque ripple in the direct torque control inverter for PMSM drive. It is actually impossible to raise the inverter switching frequency in the conventional system, although the hysterisis bandwidths for the stator flux and torque control are sufficiently diminished, because of the sampling Interval and the delay in estimating the flux and the torque In order to overcome the problem, the proposed method introduces a dithering technique into the conventional system by superposing triangular waves with high frequency and minute amplitude on the torque error. And the programable 3- stage lowpass filter is added instead of pure Integrator. Simulation results prove the feasibility of proposed strategy compared with conventional method.

• Journal of the Korean Ceramic Society
• /
• v.36 no.10
• /
• pp.1035-1039
• /
• 1999

Ferroelectric properties and reliability characteristics of(111) and (100) preferentially oriented tetragonal Pb(Zr0.2Ti0.8)O3 (PZT) thin film capacitors have been investigated as a function of the top electrode thickness. The (111) preferentially oriented film exhibits 180$^{\circ}$domain switching process with better squareness of hysterisis loop and abrupt change of small singal capacitance-voltage comparing to the (100) preferentially oriented film having 90$^{\circ}$ domain switching process. The domain swithcing process of tetragonal phase PZT is different from that of rhobohedral phase. The film with thinner top electrode shows less initial switching polarization due to less compressive stress but it exhibits better endurance characteristics due to enhancing partial switching region.

• Journal of the korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.48-55
• /
• 1982

In the present the strain gauge type torque transducers consist of solid shaft as sensor, slip ring, brush and bridge circuit as detecting circuit. So in the case of measuring the low-capacity torque, the error caused by technical mistake in mounting stain gauge on the small sensor and especially by contact resistance between slip ring and brush takes place more than the large sensor. Therefore in this study constant voltage in order to have no effect of contact resistance is supplied to the hollow shaft and Schrobron Bridge Circuit. Through the experiment good results were obtained as follows; linearity, hysterisis and zero drift as static characteristics is within 1% F.S respectively. Also when loading, zero drift is about 2% F.S.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.134-138
• /
• 2000

The physical, electrical and piezoresitive characteristics of CrN(chromiun nitride) thin-films on silicon substrates have been investigated for use as strain gauges. The thin-film depositions have been carried out by DC reactive magnetron sputtering in an argon-nitrogen atmosphere(Ar-(5~25 %)$N_2$). The deposited CrN thin-films with thickness of $3500{\AA}$nd annealing conditions($300^{\circ}C$, 48 hr) in Ar-10 % $N_2$ deposition atmosphere have been selected as the ideal piezoresistive material for the strain gauges. Under optimum conditions, the CrN thin-films for the strain gauges is obtained a high electrical resistivity, $\rho=1147.65\;{\mu}{\Omega}cm$, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal gauge factor, GF=11.17.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.447-449
• /
• 1994

This paper deals with the static characteristics of filters at the AC source in single phase PWM converter using hysterisis current control method. The filters are needed to reduce the current harmonics. In general, there are two kinds of filters which can be used for current controlled PWM converter. One is the low pass filter, the other is the resonant filter for a frequency. This paper designs these filters by analysing the characteristics. And these filters are compared through performance index such as harmonic reduction factor and the value of components which make up filters.