• 대한금속재료학회지
• /
• 제49권7호
• /
• pp.541-548
• /
• 2011

Thermomechanical fatigue (TMF) behavior of heat resistant austenitic stainless steel was evaluated in the temperature range from 100$^{\circ}C$ to peak temperatures of 600 to 800$^{\circ}C$; The fatigue lives under TMF conditions were plotted against the plastic strain range and the dissipated energy per cycle. In the expression of the inelastic strain range versus fatigue life, the TMF data obtained at different temperature ranges were located close to a single line with a small deviation; however, when the dissipated energy per cycle, calculated from the area of the stress-strain hysteresis loops at the half of the fatigue life, was plotted against the fatigue life, the data showed greater scattering than the TMF life against the inelastic strain range. A noticeable stress relaxation in the stress-strain hysteresis curve took place at the peak temperatures higher than 700$^{\circ}C$, but all specimens in this study exhibited cyclic hardening behavior with TMF cycles. Recrystallization occurred during the TMF cycle concurrent with the formation of fine subgrains in the recrystallized region, which is considered to cause the cyclic hardening of the steel.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권2호
• /
• pp.25-30
• /
• 2015

In order to realize economical applications, it is important to reduce the ac loss of 2G high-temperature superconductor coated conductors. It seems to be reasonable that a multi-filamentary wire can decrease the magnetization loss. In this study, we prepared two samples of YBCO coated conductors with striations. We measured local superconducting properties of both samples by using Low Temperature Scanning Laser and Hall Probe Microscopy (LTSLHPM). The distribution of the local critical temperature of samples was analyzed from experimental results of Low Temperature Scanning Laser Microscopy (LTSLM) near the superconducting transition temperature. According to LTSLM results, spatial distributions of the local critical temperature of both samples are homogeneous. The local current density and the local magnetization in samples were explored from measuring stray fields by using Scanning Hall Probe Microscopy (SHPM). From SHPM results, the remanent field pattern of the one bridge sample in an external magnetic field confirms the Bean's critical state model and the three bridge sample has similar remanent field pattern of the one bridge sample. The local magnetization curve in the three bridge sample was measured from external fields from -500 Oe to 500 Oe. We visualized that the distribution of local hysteresis loss are related in the distribution of the remanent field of the three bridge sample. Although the field dependence of the critical current density must be taken into account, the relation of the local hysteresis loss and the remanent field from Bean's model was useful.

• 한국지진공학회논문집
• /
• 제7권3호
• /
• pp.17-22
• /
• 2003

본 연구에서는 나노기술을 이용하여 에너지 감쇠 기능을 활용한 감쇠기 개발에 대한 연구를 하였다. 유체 감쇠기를 대체하는 완충역할을 하는 미로구조를 가지는 실리카 겔 입자를 사용하였으며, 입자에 관련한 작동 유체로는 물을 사용하여 그 효과를 검증하였다. 콜로이드 감쇠기를 구현하기 인해서는 형성된 실리카 겔 입자의 표면을 유기 실리콘 매질을 이용한 소수화 코팅 처리를 하였다. 정적 하중 상태에서의 가역적 콜로이드 감쇠기에 대한 실험을 수행하였다. 콜로이드 감쇠기내 다공질 입자의 나노 유로(pore)와 다공성 입자의 직경, 다공성 입자의 구조, 그리고 대기압 상태에서 유체의 출입을 통제하기 위한 코팅처리의 분자 간 길이와 같이 여러 가지 요인의 콜로이드 감쇠기 이력현상에 대한 영향을 평가하였다. 감쇠기의 소산 에너지양과 효율에 대해서도 조사하여 유압 감쇠기 보다 뛰어난 결과를 얻었으며 콜로이드 감쇠기로 사용 가능하다는 사실을 입증하였다.

• Smart Structures and Systems
• /
• 제19권5호
• /
• pp.487-497
• /
• 2017

Semi-active devices use the building's own motion to produce resistive forces and are thus strictly dissipative and require little power. Devices that independently control the binary open/closed valve state can enable novel device hysteresis loops that were not previously possible. However, some device hysteresis loops cannot be obtained without active analog valve control allowing slower, controlled release of stored energy, and is presents an ongoing limitation in obtaining the full range of possibilities offered by these devices. This in silico study develops a proportional-derivative feedback control law using a validated nonlinear device model to track an ideal diamond-shaped force-displacement response profile using active analog valve control. It is validated by comparison to the ideal shape for both sinusoidal and random seismic input motions. Structural application specific spectral analysis compares the performance for the non-linear, actively controlled case to those obtained with an ideal, linear model to validate that the potential performance will be retained when considering realistic nonlinear behaviour and the designed valve control approach. Results show tracking of the device force-displacement loop to within 3-5% of the desired ideal curve. Valve delay, rather than control law design, is the primary limiting factor, and analysis indicates a ratio of valve delay to structural period must be 1/10 or smaller to ensure adequate tracking, relating valve performance to structural period and overall device performance under control. Overall, the results show that active analog feedback control of energy release in these devices can significantly increase the range of resetable, valve-controlled semi-active device performance and hysteresis loops, in turn increasing their performance envelop and application space.

• Steel and Composite Structures
• /
• 제26권6호
• /
• pp.719-731
• /
• 2018

Concrete filled steel tubular (CFST) laced columns have been widely used in high rise buildings in China. Compared to solid-web columns, this type of columns has a larger cross-section with less weight. In this paper, four concrete filled steel tubular laced columns consisting of 4 main steel-concrete tubes were tested under cyclic loading. Hysteresis and failure mechanisms were studied based on the results from the lateral cyclic loading tests. The influence of each design parameter on restoring forces was investigated, including axial compression ratio, slenderness ratio, and the size of lacing tubes. The test results show that all specimens fail in compression-bending-shear and/or compression-bending mode. Overall, the hysteresis curves appear in a full bow shape, indicating that the laced columns have a good seismic performance. The bearing capacity of the columns decreases with the increasing slenderness ratio, while increases with an increasing axial compression ratio. For the columns with a smaller axial compression ratio (< 0.3), their ductility is increased. Furthermore, with the increasing slenderness ratio, the yield displacement increases, the bending failure characteristic is more obvious, and the hysteretic loops become stouter. The results obtained from the numerical analyses were compared with the experimental results. It was found that the numerical analysis results agree well with the experimental results.

• 한국산업융합학회 논문집
• /
• 제23권1호
• /
• pp.83-91
• /
• 2020

The evaluation of the compression behavior of the cushioning material is of importance to achieve appropriate packaging design. In order to change packaging design from polymeric-based to more eco-friendly cellulose-based nire effectively, comparative study on the compression behavior between these two packaging materials is crucial. In this study, the stress-strain behavior, hysteresis loss, and response characteristics for cyclic loading were analyzed through compression tests on multi-layered corrugated structure (MLCS) and expanded polystyrene (EPS) packaging materials. MLCS produced in Korea is produced by winding a certain number of single-faced corrugated paperboard, and the compression behavior of this material was turned out to be 6 stages: elastic stage, first buckling stage, sub-buckling stage, densification stage, last buckling stage and high densification stage. On the other hand, EPS's compression behavior was in 3 stages: linear elastic stage, collapse plateau, and densification stage. The strain energy per unit volume (strain energy density) of MLCS did not differ depending on the material thickness, but it showed a clear difference depending on the raw material and flute type. Hysteresis loss of MLCS ranged from 0.90 to 0.93, and there were no significant differences in the raw material and flute type. These values were about 5 to 20% greater than the hysteresis of the EPS (about 0.78 to 0.87).

• Computers and Concrete
• /
• 제31권6호
• /
• pp.537-543
• /
• 2023

To study the seismic behavior of recycled aggregate concrete filled circular steel tube (RACFCST) frames, the seismic behavior experiment of RACFCST frame was carried out to measure the hysteresis curve, skeleton curve and other seismic behavior indexes. Moreover, based on the experimental study, a feasible numerical analysis model was established to analyze the finite element parameters of 8 RACFCST frame specimens, and the influence of different variation parameters on the seismic behavior index for RACFCST frame was revealed. The results showed that the skeleton curve of specimens under different axial compression ratios were divided into three stages: elastic stage, elastic-plastic stage and descending stage, and the descending stage was relatively stable, indicating that the specimen had stronger deformation capacity in the descending stage. With the increase of axial compression ratio, the peak bearing capacity of all specimens reduced gradually, and the reduction was less than 5%. With the decrease of beam-column linear stiffness ratio, the peak bearing capacity decreased gradually. With the decrease of yield bending moment ratio of beam-column, the peak bearing capacity decreased gradually, and the decreasing rate of peak bearing capacity gradually accelerated. In addition, compared with the axial compression ratio, the beam-column linear stiffness ratio and the yield bending moment ratio of beam-column had a more significant influence on the peak bearing capacity of RACFCST frame.

• 한국전산구조공학회논문집
• /
• 제31권2호
• /
• pp.115-120
• /
• 2018

본 논문에서는 PSC 거더의 긴장력을 계측하기 위한 EM 센싱 기법을 다양한 PS 텐던에 적용하기 위하여 PS 강종별 긴장력 변화에 따른 자기이력 모니터링 결과를 소개한다. PSC 교량의 성능평가에 있어 PS 텐던의 긴장력은 매우 중요한 인자이나 현재는 시공시 설계 긴장력의 도입 여부만을 검증하고 그 이후에는 긴장력 관리가 이루어지지 않는 실정이다. 이를 계측하기 위하여 EM 센서를 이용하여 긴장력을 계측하는 기법에 대한 연구가 이루어지고 있으나 PSC 거더에 사용되는 모든 PS 텐던에 대한 연구는 이루어지지 않았다. 이에 본 연구에서는 PSC 교량에 주로 사용되는 B, C, D종 PS 텐던에 대해 EM 센싱 기법을 적용하기 위하여 각 강종별 긴장력에 따른 자기 이력 변화를 모니터링하였다. 이를 위해 B종 12.7mm, C종 15.2mm, D종 15.2mm PS 텐던 시편에 50, 100, 150, 180kN의 긴장력을 도입하고 각 긴장력 단계마다 자기 이력 곡선을 EM 센서를 통하여 계측하였다. 계측 결과 각 긴장력 단계마다 그 투자율이 정량적으로 변화하는 것을 확인할 수 있었다. 특히 B, C 종의 경우 단면적이 달라 선형회귀분석식의 상수는 상이하지만 유사한 기울기를 가지고 변화하고 D종의 경우 다른 강종과 다른 기울기를 가지고 변화하는 것을 확인하였다.

• 한국지반공학회논문집
• /
• 제39권1호
• /
• pp.15-25
• /
• 2023

최근 집중 강우의 증가로 인한 사면 붕괴가 증가하고 있으며, 대규모 사면 붕괴가 빈번하게 발생하고 있다. 사면 붕괴로 인한 인명 및 재산 피해를 최소화하기 위해서 사면 경보 시스템에 사면 계측이 활용되고 있다. 사면 계측은 특정 지점에서 대한 결과를 측정하기 때문에 전반적인 사면의 거동을 파악하기 어려우므로 수치 해석을 함께 수행되어야 한다. 강우 침투시 사면의 거동을 파악하기 위해서 강우 뿐만 아니라 증발산이 고려되고 있으며, 불포화 함수 특성 곡선의 건조 과정을 적용하여 수치해석이 진행 되고 있다. 하지만, 불포화 함수 특성 곡선의 이력 현상은 수치해석 결과에 영향을 미친다. 따라서, 본 연구에서는 증발산 산정 방법과 증발산을 경계 조건에 적용하는 방법을 제시하고, 불포화 사면의 현장 계측 결과와 경계 조건과 침투 조건을 고려한 수치해석 결과를 비교하였다. 계측 지점의 흡수력 변화와 상관 계수를 비교하였을 때, 불포화 함수 특성 곡선의 건조과정과 습윤과정에 따라 증발산에 대한 영향이 다르게 나타났다. 또한, 증발산 적용을 통하여 건기와 우기시의 흡수력 변화가 실제 계측 결과와 근접하게 나타나는 것을 통하여 증발산 적용시 불포화 사면의 지표면에서 발생하는 수분 이동을 더 합리적으로 예측할 수 있다고 판단된다.

• 한국지반신소재학회논문집
• /
• 제10권3호
• /
• pp.25-32
• /
• 2011

본 연구에서는 자동 흙-함수특성곡선 시험장치를 이용하여 새만금지역에서 채취한 준설토의 모관흡수력과 체적함수비를 측정하였다. 측정결과를 토대로 Van Genuchten(1980)의 방법을 이용하여 흙-함수특성곡선(SWCC)을 산정하였다. 동일한 유효포화도에서 건조과정의 모관흡수력은 습윤과정의 모관흡수력보다 크게 나타났다. Lu and Likos(2006)의 방법을 이용하여 모관흡수력에 따른 흡입응력을 산정하고, 흙-함수특성곡선(SWCC)의 불포화 관련계수를 토대로 흡입응력특성곡선(SSCC)을 예측하였다. 건조과정의 흡입응력은 유효포화도가 증가함에 따라 증가하다가 감소하지만 습윤과정의 흡입응력은 유효포화도가 증가함에 따라 지속적으로 감소한다. 또한 동일한 유효포화도에서 건조과정의 흡입응력은 습윤과정의 흡입응력보다 크게 나타났다. 한편 van Genuchten(1980)의 방법을 이용하여 투수계수함수(HCF)를 예측하였다. 체적함수비가 증가함에 따라 불포화 투수계수는 증가하며, 동일한 모관흡수력에서 건조과정의 투수계수가 습윤과정의 투수계수보다 크게 나타났다. 흙-함수특성곡선(SWCC)과 흡입응력특성곡선(SSCC)의 산정결과에 의하면 건조 및 습윤과정에서 흡입응력 혹은 모관흡수력에 대한 이력현상이 발생되었다. 이러한 이력현상은 흙입자 사이의 간극수로 인한 잉크병 효과에 의한 것이다.