• 한국수소및신에너지학회논문집
• /
• 제34권6호
• /
• pp.758-766
• /
• 2023

Multi-copter of unmanned aerial vehicle (UAV) was initially developed as strategic technology in the only military field, but it is developing into an industrial field with a wide range of applications in the civil sector based on the development and convergence of aviation technology and information and communication technology. Currently, the degree of utilization of multi-copter is increasing in various industries for the purpose of performing classic tactical missions, logistics transportation, farm management, internet supply, video filming, weather management, life-saving, etc, and active technology development responding to market demand. Existing commercial multi-copter mainly use an electric energy propulsion system consisting of an electric battery and a brushless direct current (BLDC) motor. It is the limitations for usage in the flying time (up to 20 minutes) and payload (less than 20 kg). this study aims to overcome these limitations and expand the commercialization of engine-powered multi-copter of UAV in various industries in the futures.

• 한국자동차공학회논문집
• /
• 제18권4호
• /
• pp.84-91
• /
• 2010

Owing to revolutionary developments in automobile technologies, a variety of advanced vehicles - hybrid vehicle, hydrogen fuel-cell vehicle, electric vehicle, etc. - emerges recently. The safety is getting more important for developing automobiles. The electro-magnetic compatibility has to be assured, since those advanced vehicles are equipped with various new electronic systems. Electro-magnetic compatibility tests, in general, consist of an EMI(electro-magnetic interference) test and an EMS (electro-magnetic susceptibility) test. We investigated the susceptibility test method suggested in KMVSS (Korean Motor Vehicle Safety Standard) as the EMS test method. A series of experiments results that the above test method should be partially revised to comply with a Korean governmental standard method. In this paper, the some directions of modifications are presented to enhance the quality of the above EMS test method.

• 한국가스학회지
• /
• 제28권1호
• /
• pp.85-99
• /
• 2024

수소전기차의 보급 확대가 빠르게 이루어지며 수소충전소의 모델 또한 다양화되고 있다. 이에 따라 종류별 수소 충전소의 안전에 대한 이슈가 대두되고 있다. 본 연구에서는 승용·버스·트럭 등 다차종 동시 수소충전이 가능한 수소 스테이션의 정량적 위험성평가를 진행하였다. 정량적 위험성평가에 범용적으로 사용되는 Gexcon 사(社)의 Effects&Riskcurves Software를 활용하여 수소 누출에 따른 화재, 폭발 등의 시나리오를 부여하였다. 이를 통해 복사 열, 폭발 과압에 의한 피해 영향 거리를 계산해냈으며, 주변 건물 및 인구에 미치는 위험도를 측정하였다. 피해 영향 거리가 가장 크게 나타난 것은 충전설비 및 고압 압축가스 설비의 화재 및 폭발이었으며 개인적 및 사회적 위험도에 가장 크게 기여한 설비는 고압 압축가스 설비로 나타났다. 이에 따라 충전설비 및 압축가스 설비에 대한 안전거리를 보수적으로 책정하며 적절한 방호조치를 설치한다면 수소 누출 사고 발생 시 인적·물적 피해 최소화에 기여할 수 있을 것으로 검토된다.

• 전기학회논문지
• /
• 제65권11호
• /
• pp.1925-1930
• /
• 2016

Fuel cell power generation system, unlike conventional energy sources, converts chemical energy into electrical energy through electrochemical reaction of hydrogen and oxygen. This paper presents the control of interleaved multi-phase boost converter as the feasibility study on small-scale prototype electric railway vehicle application using fuel cell generation system. PSIM simulation program is to be used to implement the modeling of the electrical fuelcell as well as traction motor control with interleaved multi-phase boost converter. Comparing the input current ripple rate, two-phase interleaved boost converter is less than the boost converter. But the more multi-phase not less proportional to the ripple factor. we confirmed that the amplitude of the input current ripple rate of converter depend on duty ratio.

• 한국가스학회지
• /
• 제16권2호
• /
• pp.25-30
• /
• 2012

본 논문에서는 알루미늄 라이너와 탄소섬유/에폭시 및 유리섬유/에폭시로 구성된 복합소재 압력용기에 대한 응력 안전성 연구결과를 제시하고 있다. 9.2L의 저장용량을 갖는 수소가스 자동차용 복합소재 압력용기에는 35MPa의 충전압력으로 수소가스를 압축한 경우이다. FEM 해석결과는 미국의 수소가스 압력용기에 대한 DOT-CFFC와 한국의 KS B ISO 인증기준에 기반하여 평가하였다. FEM 해석결과에서 알루미늄 라이너에 걸리는 응력 247MPa는 알루미늄 항복강도(272MPa)의 95%에 해당하는 안전기준에 비해 충분히 낮다는 결과이다. 그리고 알루미늄의 표면에 감은 탄소섬유 복합소재는 후프방향과 헤리컬방향에서 발생한 최대탄소섬유응력이 29.43%와 28.87% 수준으로 각각 나타났기 때문에 최소파열압력에서의 최대섬유응력 대비 30% 이하를 유지해야 한다는 안전기준에 부합하므로 안전하다. 또한, 탄소섬유 복합소재에 대한 응력비는 후프방향과 헤리컬방향에 대해 3.4와 3.46으로 각각 예측되었기 때문에 최소안전기준인 2.4보다 높아 안전한 것으로 나타났다.

• 한국수소및신에너지학회논문집
• /
• 제12권2호
• /
• pp.129-136
• /
• 2001

An investigation on the A/V(ampere/volt) gradient according to the concentration and the kind of solution in a electrolyzer is carried out to obtain the basic data on the ultrasonic application for the efficiency elevation of the hydrogen fuel production. KOH is selected as an electrolyte and concentrations are 0%, 10%, 20% and 30%. The solutions are city water, city water with nitrogen. distilled water and distilled water with nitrogen. The Electrochemical analyzer(BAS Co.) is used as a measuring device to observe the A/V gradient. And the limit of volt is from -3000mV to +3000mV. The 28kHz magnetic transducer is selected to give them ultrasonic forcing. In results, it is clarified that ultrasonic influences the A/V gradient in the electrolytic solution.

• 한국수소및신에너지학회논문집
• /
• 제22권6호
• /
• pp.852-858
• /
• 2011

This paper is aiming to estimate the mutual influence of the stack cooling performances with the operation modes of the thermal management system for the hydrogen fuel cell vehicles. The heat capacity of the thermal management system was measured by varying the operating modes such as stack cooling heat exchanger only (Mode 1), stack cooling and electric devices cooling heat exchangers (Mode 2), and stack cooling and electric devices cooling heat exchangers with an operation of the condenser (Mode 3).As the results, Performance of the thermal management system (TMS) at Mode 3 decreased up to 34.0%, compared with the result of the Mode 1. In addition, in order to optimize the performance of TMS, the entropy change of stack cooling heat exchanger using irreversibility analysis technique was analyzed with the relationship between entropy generation and entering air velocity of the thermal management system.

• 한국수소및신에너지학회논문집
• /
• 제21권3호
• /
• pp.149-157
• /
• 2010

The electromagnetic characteristics of FCEVs (fuel cell electric vehicles) are much different from the existing combustion engine cars as well as hybrid, plug-in-hybrid, and pure electric vehicles due to the high voltage/current generated by a fuel cell stack which uses a compressed hydrogen gas reacted with oxygen. To operate fuel cell stack efficiently, BOP (Balance of Plant) is essential. BOP systems are used many not only for motors in water pump, air blower, and hydrogen recycling pump but also inverters for these motors. Since these systems or components are connected by high voltage cables, EMC (Electromagnetic compatibility) analysis for high voltage/current cable is the most important element to prevent the possible electric functional safety errors. In this paper, electromagnetic fields of high current/voltage cable for FCEVs is studied. From numerical analysis results, time harmonic magnetic field strength of high current/voltage cable have difference of 20～28 dB according to phase. EMI result considered ground effect of FECV at 10 m shows difference of 14.5 dB at 30 MHz and 2.8 dB at 230 MHz compared with general cable.

• 한국수소및신에너지학회논문집
• /
• 제27권2호
• /
• pp.155-162
• /
• 2016

A proton exchange membrane fuel cell (PEMFC) produces only water at cathode by an electrochemical reaction between hydrogen and oxygen. The generated water is transported across the membrane from the cathode to the anode. The transported water collected in water-trap and drained to the cathode within the humidifier outlet. If the condensate water is not being drained at the appropriate time, condensate water in the anode can cause the performance degradation or fuel efficiency degradation of fuel cell by the anode flooding or unnecessary hydrogen discharge. In this study, we proposed an optimization method of condensate water drain logic for the water drain performance and the water drain algorithm as considered the condensate water generating speed prep emergency case. In conclusion, we developed the water management strategy of fuel processing system (FPS) as securing fuel efficiency and operating stability.

• 한국산업융합학회 논문집
• /
• 제27권3호
• /
• pp.573-580
• /
• 2024

Recently, the special alloy, for instance, such as Monel and Inconel, is used for valves, bolt/nuts, and fittings in semiconductor facility, FCEV(fuel cell electric vehicle) and hydrogen gas station, to reduce the hydrogen embrittlement. Even though the Monel material has high cost, it is recommended to use for the cases of ultra high pressure, ultra high leak-proof and so on. The purpose of this study is to investigate the characteristics of Monel material within elastic limit through the comparative analysis when Monel material is extruded or drawn. As the results, the deformation of Monel material was increased as the number of pass was increased, further, the deformation of Monel material by drawing was larger than that by extrusion. In the safety factor, the case that load is less than 420kN, the plastic deformation due to drawing could be happened faster than that due to extrusion. However, the case of more than 420kN, it showed that the plastic deformation for extrusion and drawing was almost similar.