• 유공압시스템학회논문집
• /
• 제6권1호
• /
• pp.25-31
• /
• 2009

This study presents an analytical model of hydraulic clutch system of a power shift transmission to analyze pressure modulation characteristics. A typical hydraulic clutch system was modeled by using AMESim in which the parameters of major components were measured for simulation. Test apparatus was established using the components of power shift and power shuttle clutches with instrumental equipment. The results of simulation and experiment were so close that the proposed analytical model in this study was validated. However the cylinder model analogized clutch dynamics need to be improved in future study. The effects of parameters of orifice diameter, accumulator stroke and oil temperature on pressure modulation were analyzed respectively. The results of parameter sensitivity analysis show that modulation time and set pressure can be easily adjusted by changing parameter values. It is also found that the hydraulic clutch system used in this study is so susceptible to oil temperature that cooling equipment is necessary.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제15권3호
• /
• pp.122-128
• /
• 2007

Heat transfer distributions and friction factors in square channels (3.0 ${\times}$ 3.0 cm) with twisted tape inserts and with twisted tape inserts plus interrupted ribs are respectively investigated. The rib height-to-channel hydraulic diameter ratio, $e/D_h$, is kept at 0.067 and test section length-to-hydraulic diameter ratio, $L/D_h$ is 30. The square ribs are arranged to follow the trace of the twisted tape and along the flow direction defined as axial interrupted ribs. The twisted tape is 0.1 mm thick carbon steel sheet with diameter of 2.8 cm, length of 90 cm, and 2.5 turns. Two heating conditions are investigated for test channels with twisted tape inserts and rib turbulators: (1) electric heat uniformly applied to four side walls of the square duct, and (2) electric heat uniformly applied to two opposite ribbed walls of the square channel. Results show that the twisted tape with interrupted ribs provides a higher overall heat transfer performance over the twisted tape with no ribs.

• 유공압시스템학회논문집
• /
• 제7권3호
• /
• pp.7-12
• /
• 2010

In the case of hydraulic piston motor, hydrostatic bearing is designed to be adapted the hydrostatic bearing for the relative lubrication in the structural design. It's available to make it highly efficient and that's why it's widely used. The thing which largely influence the high pressure, the high efficiency, and the life is the hydrostatic bearing between a shoe and a swash plate. In this study, with the most general "hydrostatic bearing shoe" that has one recess as the subject of this research, I designed and made the 4 kind of piston shoe that have different orifice diameter each other, and studied the features of the hydrostatic bearing by observing the change of the leakage flow rate, the torque and the volumetric efficiency through experiments on the changes of the pressure & the speed of the revolution. As a result, the bigger diameter of the orifice, the less torque. And with an increase of the orifice diameter under the high pressure, the leakage flow rate decreased remarkably. Also it was observed the leakage flow rate increased linearly according to the increase of the supply pressure.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.117-120
• /
• 2008

Numerical simulations and experiment of a hydrodynamic and thermally developed turbulent flow through square ducts (3.0 ${\times}$ 3.0 cm) with twisted tape inserts and with twisted tape inserts plus interrupted ribs are conducted to investigate regionally averaged heat transfer and friction factors. Turbulent swirl flows having Reynolds numbers ranging from 8,900 to 29,000, a rib height-to-channel hydraulic diameter(e/D$_h$) of 0.067, and a length-to-hydraulic diameter(L/D$_h$) of 30, are considered. The square ribs are arranged to follow the trace of the twisted tape and along the flow direction defined as axial interrupted ribs. The twisted tape has 0.1 mm thick carbon steel sheet with diameter of 2.8 cm, length of 90 cm, and 2.5 turns. Each wall is composed of isolated aluminum sections, and two cases of surface heating are set. The results show that uneven surface heating enhances the heat transfer coefficient over uniform heating conditions, and square ducts with twisted tape inserts plus interrupted ribs produces the best overall transfer performance.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.178-184
• /
• 2005

The present study investigates the effects of bleed flow on heat/mass transfer and pressure drop in a rotating channel with transverse rib turbulators. The hydraulic diameter ($D_h$) of the square channel is 40.0 mm. The bleed holes are located between the rib turburators on leading surface and the hole diameter (d) is 4.5 mm. The square rib turbulators are installed on both leading and trailing surfaces. The rib-to-rib pitch is 10.0 times of the rib height (e) and the rib height-to-hydraulic diameter ratio ($e/D_h$) is 0.055. The tests were conducted at various rotation numbers (0, 0.2, 0.4), while the Reynolds number and the rate of bleed flow to main flow were fixed at 10,000 and 10%, respectively. The results suggest that the heat/mass transfer characteristics in the internal cooling passage are influenced by rib turbulators, bleed flow and the Cariolis force induced by rotation. For the rotating ribbed passage with bleed flow, the heat/mass transfer on the leading surface is hardly affected by bleed flow, but that on the trailing surface decreases due to the diminution of main flow. The results also show that the friction factor decreases with the bleed flow.

• 한국관개배수논문집
• /
• 제7권2호
• /
• pp.49-56
• /
• 2000

A hydraulic model study have been carried out on roughness coefficient of corrugated helical steel pipe. The study was performed in the 0.6m wide flume of Hydraulic Laboratory for the pipe diameter of 0.6m and 1.6m. Additional study was performed in 2m wi

• Computers and Concrete
• /
• 제18권6호
• /
• pp.1135-1151
• /
• 2016

For investigating the effect of the pre-existing joints on the initiation pattern of hydraulic fractures, the numerical simulation of circular holes under internal hydraulic pressure with a different pattern of the joint distributions are conducted by using a finite element code, FRANC2D. The pattern of hydraulic fracturing initiation are scrutinized with changing the values of the joint length, joint offset angle. The hydraulic pressures with 70% of the peak value of borehole wall breakout pressure are applied at the similar models. The simulation results suggest that the opening-mode fracture initiated from the joint tip and propagated toward the borehole for critical values of ligament angle and joint offset angle. At these critical values, the crack grow length is influenced by joint ligament length. When the ligament length is less than 3 times the borehole diameter the crack growth length increases monotonically with increasing joint length. The opening-mode fracture disappears at the joint tip as the ligament length increases.

• 한국기계가공학회지
• /
• 제18권7호
• /
• pp.14-21
• /
• 2019

Large-diameter hydraulic devices such as the hydraulic reservoir in aircraft that serves to balance the hydraulic pressure in the various hydraulic devices in the cabin and to store hydraulic oil are operated by the internal piston systems. However, since this operates in an environment with high temperature and humidity, it may cause the inner surface to flake during its operation. Therefore, an anodizing surface treatment is applied to improve the corrosion resistance, abrasion resistance, and smooth operation. However, anodizing increases the surface roughness. Accordingly, the polishing process that improves the surface roughness after anodizing is important. However, the existing polishing process is performed manually, which results in an inefficient process. Therefore, in this study, we selected the optimum polishing conditions for effective polishing using the experimental design to improve the polishing process for the $Al_2O_3$ film that forms after anodization. Through experiments, we confirmed that the surface uniformity after polishing was superior as the feed rate was slower when the same polishing time had been applied.

• 한국추진공학회지
• /
• 제21권5호
• /
• pp.19-28
• /
• 2017

본 연구에서는 원형 노즐과 타원형 노즐을 이용하여 공동현상과 수력튀김 현상이 유동특성에 어떠한 영향을 미치는지 파악하고자 하였다. 이를 위해 오리피스 길이 대 직경비(L/d)와 타원형 노즐의 종횡비(a/b)가 서로 다른 분사기들을 제작하여 분무실험을 수행하였다. 분사압력 증가에 따라 공동현상이 발생할 경우 유량계수가 서서히 감소하였으나 수력튀김 영역에서는 유량계수가 급격히 떨어진 후 일정한 값을 유지함을 확인하였다. 하지만 타원형 노즐에서 장축지름(a)과 단축지름(b) 대비 오리피스 길이의 비인 L/b가 8 이상, L/a가 8 이하인 경우, 유량계수 및 액체제트 형상은 기존의 원형 노즐과는 상당히 다른 결과를 나타내었다. 정상유동 상태인 경우 타원형 노즐에서 분사된 액주는 원형 노즐과는 달리 하류로 가면서 장축에서는 분무각이 감소하였으며 단축에서는 분무각이 커지는 모습을 보였다.

• 대한환경공학회지
• /
• 제27권12호
• /
• pp.1305-1310
• /
• 2005

하상여과에서 집수관의 최적 설계를 위한 방편으로 여러 개의 모래통을 이용하여 모형 집수관 실험을 수행하였다. 집수정의 수위, 집수관의 직경, 집수관의 길이, 그리고 모래의 투수계수를 변화시키면서 모형 집수관을 운영하였으며, 집수관 표면에서의 잔류 수두와 집수관 각 부위에서의 여과수 유입율, 그리고 집수정에서의 산출유량을 측정하였다. 실험결과 모래층에서의 저항에 비해 집수관에서의 저항이 작아서 집수관 표면에서의 잔류수두가 수평에 가까운 경우 효율적인 집수관임을 알 수 있었다. 집수관의 여과수 유입율은 집수정에 근접할수록 지수함수적으로 증가하였고, 집수관의 직경이 작을수록 그리고, 대수층의 투수계수가 클수록 이 지수함수의 기울기는 증가하였다. 집수관의 길이와 직경이 증가하면 산출유량은 증가하지만 그 한계생산성은 감소하였다. 효율적인 하상여과를 위해서는 집수관에서의 축방향 유속을 줄이는 것이 중요함을 알 수 있었으며, 본 연구의 조건에서는 이 유속이 1 m/sec를 넘을 경우 우물의 효율이 크게 감소함을 알 수 있었다.