Journal of the Korean Society of Manufacturing Process Engineers (한국기계가공학회지)

The Korean Society of Manufacturing Process Engineers (한국기계가공학회)
권호 표지
DOI QR코드

DOI QR Code

Optimization of Polishing Conditions for Anodized Inner Surfaces in Large Hydraulic Devices

아노다이징 처리된 대형 유압장치의 내면에 대한 연마 조건의 최적화

  • Choi, Su-Hyun (Department of Mechanical Engineering, Changwon National University) ;
  • Cho, Young-Tae (Department of Mechanical Engineering, Changwon National University)
  • Received : 2019.04.11
  • Accepted : 2019.05.22
  • Published : 2019.07.31
Download PDF
⟨ Previous Next ⟩

Abstract

Large-diameter hydraulic devices such as the hydraulic reservoir in aircraft that serves to balance the hydraulic pressure in the various hydraulic devices in the cabin and to store hydraulic oil are operated by the internal piston systems. However, since this operates in an environment with high temperature and humidity, it may cause the inner surface to flake during its operation. Therefore, an anodizing surface treatment is applied to improve the corrosion resistance, abrasion resistance, and smooth operation. However, anodizing increases the surface roughness. Accordingly, the polishing process that improves the surface roughness after anodizing is important. However, the existing polishing process is performed manually, which results in an inefficient process. Therefore, in this study, we selected the optimum polishing conditions for effective polishing using the experimental design to improve the polishing process for the $Al_2O_3$ film that forms after anodization. Through experiments, we confirmed that the surface uniformity after polishing was superior as the feed rate was slower when the same polishing time had been applied.

Keywords

References

  1. Kim, J. S., "The Effect of Temperature and Humidity on the Pressure of the Bootstrap Reservoir in the Aircraft," MS Thesis, Gyeongsang National University, Republic of Korea, 2012.
  2. Aaltonen, J., Koskinen, K. T., Vilenius, M., Vaaraniemi, K., "Pump Supply Pressure Fluctuations in the Semi-closed Hydraulic Circuit with Bootstrap Type Reservoir," Proceeding of Scandinavian International Conference on Fluid Power, pp. 117-133, 2007.
  3. Tao, L., "Study on bootstrap reservoir type pressurized system for civil aircraft hydraulic supply system," Proceeding of 2016 IEEE International Conference on Aircraft Utility Systems, pp. 1117-1121, 2016.
  4. Kim, W. B., "A Study on Improvement of Manufacturing Process for Airplane Reservoir of Al7075," MS Thesis, Changwon National University, Republic of Korea, 2016.
  5. Seong, C. H., “Characteristics of Surface Roughness in the High Speed Micro Turning of Aluminum Alloy,” Journal of the Korean Society of Precision Engineering, Vol. 16, No. 7, pp. 94-100, 1999.
  6. Jun, J. U., Jung, J. S., Ha, M. K., “Influence of Surface Roughness by Feed-rate and Side-rake Angle at Turning of Non-ferrous Metals,” Journal of the Korean Society of Manufacturing Technology Engineering, Vol. 10, No. 4, pp. 1-6, 2001.
  7. Nalbant, M., Gokkaya, H., Sur, G., "Application of Taguchi method in the optimization of Cutting Parameters for Surface Roughness in Turning," Materials & Design, Vol. 28, 1379-1385, 2007. https://doi.org/10.1016/j.matdes.2006.01.008
  8. Asilturk, I., Akkus, H., "Determining the Effect of Cutting Parameters on Surface Roughness in Hard Turning using the Taguchi Method," Measurement, Vol. 44, 1697-1704, 2011. https://doi.org/10.1016/j.measurement.2011.07.003
  9. Thamizhmanii, S., Saparudin, S., Hasan, S., "Analysis of Surface Roughness by Turning Process using Taguchi Method," Journal of Achievements in Materials and Manufacturing Engineering, Vol. 20, pp.503-506, 2007.
  10. Nimase, R. N., Khodke, P. M., "Effect of Machining Parameters on Surface Roughness of Al-7075 Alloy in End Milling," International Research Journal of Engineering and Technology, Vol. 2, pp.1505-1508, 2015.
  11. Ferreira, S. L. C., Bruns, R. E., Ferreira, H. S., Matos, G. D., David, J. M., Brandao, G. C., da Silva, E. G. P., Portugal, L. A., dos Reis., P. S., Souza, A. S., dos Santos, W. N. L., "Box-behnken design: An Alternative for the Optimization of Analytical Methods," Analytica Chimica Acta, Vol. 597, 179-186, 2007. https://doi.org/10.1016/j.aca.2007.07.011
  12. Li, M., Feng, C., Zhang, Z., Chen, R., Xue, Q., Gao, C., Sugiura, N., "Optimization of Process Parameters for Electrochemical Nitrate Removal using Box-Behnken Design" Electrochimica Acta, Vol. 56, pp.265-270, 2010. https://doi.org/10.1016/j.electacta.2010.08.085
  13. Kilickap, E., "Modeling and Optimization of Burr Height in Drilling of Al-7075 using Taguchi Method and Response Surface Methodology," The International Journal of Advanced Manufacturing Technology, Vol. 49, pp.911-923, 2010. https://doi.org/10.1007/s00170-009-2469-x
  14. Manohar, M., Joseph, J., Selvaraj, T., Sivakumar, D., "Application of Box Behnken Design to Optimize the Parameters for Turning Inconel 718 using Coated Carbide Tools," International Journal of Scientific & Engineering Research, Vol. 4, No. 4, pp.620-642, 2013.