• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.2
• /
• pp.154-161
• /
• 2014

Naval ships have hull appendages which are more exposed to the outside because of its small block coefficient compared with commercial ships. These exposed hull appendages like skeg, strut and shaft line affect the maneuverability of a ship. The effect of hull appendages has considered at initial design stage to estimate more accurate maneuverability. In this paper, sensitivity analysis is used to analyze the effect on maneuverability by hull appendages. 3 DOF maneuvering equations based on Mathematical Modelling Group (MMG) model are used and propeller & rudder model are modified to reflect the characteristics of twin propeller & twin rudder. Numerical maneuvering simulations (Turning test, Zig-zag test) for benchmark naval vessel, David Taylor Model Basin (DTMB) 5415 are performed. In every simulation, it is calculated that stability indices and maneuverability characteristics (Tactical Dia., Advance, 1st Overshoot, Time of complete cycle) with respect to the parameters (area times lift coefficient slope, attachment location) of hull appendages. As a result, two regression formulas are established. One is the relation of maneuverability characteristics and stability indices and the other is the relation of stability indices and hull appendages.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.267-274
• /
• 2018

A variety of appendages are attached to coastal and offshore fishing boats to improve stability during navigation or fishing operations (stability performance and roll reduction). These appendages are generally classified into three types, which are shown in Fig. 1. The numerical calculations were conducted for the following eight cases: one case of a bare hull, three cases where a single appendage attached, three cases of a pair of appendages attached, and one case where all three appendages were attached. Table 1 presents the main dimensions of the bare hull and Table 2 describes the main dimensions of the three appendages. The fluid dynamic performance with regard to the three hull appendages was evaluated via CFD for the following cases: each of the appendages attached independently, a pair of appendages attached, and all three appendages attached simultaneously. The No. 1 appendage showed that pressure resistance was proportionally greater than friction resistances. Both Nos. 2 and 3 appendages showed comparable levels of pressure and friction resistances. The correlation between appendages was minimal in the case of pairs and Comparing the cases of the No. 2 appendage attached and all appendages attached, at 11 kn, the EHP showed an difference of 9 %.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.2
• /
• pp.39-47
• /
• 1997

In the present paper, viscous flow fields around a wigley hull with appendages are analysed to study interactions between the hull and appendages. Navier-Stokes and continuity equations are solved by a finite volume method in a body-fitted coordinate system which conforms three dimensional ship geometries with appendages. A Sub-Grid Scale(SGS) turbulent model is used for a calculation of high Reynolds number flow. Numerical computations has been done for a Wigley hull form at $Rn=1.0{\times}10^6$. The results show that the present approach can predict, at least in qualitative sense, the influence of the appendages upon the flow field around a ship.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.4
• /
• pp.1-7
• /
• 2003

Large Passenger Ferry has been delivered with a tendency of high speed since 1990´s. More than 50 ferries that exceed 25 knots in service speed are operating or under construction these days. Therefore, the hull form development for the large size ferry should be carefully carried out with some design points such as high service speed, severe criteria for stability, and complex design of appendages. This paper reviewed principal particulars and hull form characteristics of a high-speed large passenger ferry. It is also suggested the optimization method of hull form and appendages in point of resistance & propulsion performance. Finally, it is also introduced a high-speed large passenger ferry developed by Samsung Heavy Industries Co., Ltd., the key design points in hull form development.

• Journal of Ship and Ocean Technology
• /
• v.10 no.4
• /
• pp.12-23
• /
• 2006

In this paper, a numerical study is carried out to investigate the turbulent flow around a twin-skeg container ship model with rudders including propeller effects. A commercial CFD code, FLUENT is used with body forces distributed on the propeller disk to simulate the ship stem and wake flows with the propeller in operation. A multi-block, matching, structured grid system has been generated for the container ship hull with twin-skegs in consideration of rudders and body-force propeller disks. The RANS equations for incompressible fluid flows are solved numerically by using a finite volume method. For the turbulence closure, a Reynolds stress model is used in conjunction with a wall function. Computations are carried out for the bare hull as well as the hull with appendages of a twin-skeg container ship model. For the bare hull, the computational results are compared with experimental data and show generally a good agreement. For the hull with appendages, the changes of the stem flow by the rudders and the propellers have been analyzed based on the computed result since there is no experimental data available for comparison. It is found the flow incoming to the rudders has an angle of attack due to the influence of the skegs and thereby the hull surface pressure and the limiting streamlines are changed slightly by the rudders. The axial velocity of the propeller disk is found to be accelerated overall by about 35% due to the propeller operation with the rudders. The area and the magnitude of low pressure on the hull surface enlarge with the flow acceleration caused by the propeller. The propellers are found to have an effect on up to the position where the skeg begins. The propeller slipstream is disturbed strongly by the rudders and the flow is accelerated further and the transverse velocity vectors are weakened due to the flow rectifying effect of the rudder.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.1
• /
• pp.50-56
• /
• 2009

The hydrodynamic effect of appendages for high-speed passenger vessels, such as Ro-Pax, Ro-Ro and cruiser vessels, is very severe and, therefore, it is essential to carry out the design of appendages for high-speed passenger vessels from the preliminary design stage to the final detail design stage through a full survey of the reference vessels together with sufficient technical investigation. Otherwise, many problems would be caused by mismatches between the appendages and the hull form. This paper investigates the design characteristics of some appendages, such as the side thruster, the shaft-strut, and the stern wedge, based on the design experience accumulated at Samsung, on CFD, and on model test results for high-speed passenger vessels. Further to this investigation, some practical and valuable design guidelines for such appendages are suggested.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.3
• /
• pp.38-45
• /
• 1998

In this parer, the effects of a skeg, rudder and stern hull form on the manoeuvrability of a container carrier with small length to draft ratio have been investigated through a series of model test. Rudder open water tests and PMM tests were carried out with varying rudder area, afterbody appendages and stern hull form to investigate their effects on the manoeuvrability. The MMG model developed in Japan was used for the manoeuvring simulation with experimentally obtained hydrodynamic coefficients. The result showed that the effects by the variation of stern profile and the skeg below stern bulb are much larger than those by any other types of appendages in improving directional stability of the vessel.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.3
• /
• pp.247-255
• /
• 2019

In this study, to predict the noise of a submarine propeller which is going to become bigger and faster, the non - cavitating propeller noise was predicted based on the numerical analysis which considering the interaction of the hull - appendages - propeller. In order to predict the radiated noise of the propeller, the flow field for the entire region of hull-appendages-propeller was computed by CFD (Computational Fluid Dynamics). And the noise for the thickness noise and the load noise was numerically predicted using FW-H (Ffwocs Williams-Hawkings) acoustic analogy. Numerical noise prediction results were verified by model tests and showed good agreement with the measurement results in predicting total noise level and low frequency noise.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.3
• /
• pp.320-329
• /
• 2017

In this research, we have calculated characteristics of wave-piercing high-speed planing hull, by using a RANS solver and overset grid method, for comparing with experimental measurements of that and simulating with several appendages, since the computed results of commercial CFD code look reasonable for the prediction of the performances of planing hulls on calm water in planing conditions. As a result, it is confirmed that the dynamic instability phenomena in pitch and heave motions (porpoising) occurred after a certain $Fn_V$, and effectively suppressed using some of appendages, especially the 0.5L spray rail is suppressed to 24-55 % in the pitch motion and 33-55 % in the heave motion. In spray phenomenon, 1L hard chine suppress spray effectively and it is effective to set the angle of appendages to be less than $0^{\circ}$ in order to suppress wave.

• Journal of computational fluids engineering
• /
• v.20 no.4
• /
• pp.21-27
• /
• 2015

Flow field around the KRISO 3600TEU container ship is computed using a surface generated based on interpolations of station lines, which are given in a body plan of the ship, without using any CAD program. An interpolation method is suggested based on inscribed circles to generate curves between two neighboring station lines. The interpolated surface is saved in a STL format to use the snappyHexMesh utility of the openfoam. Computed resistance of the ship is compared with experimental and other computational results and the effects of the interpolation of neighboring station lines on the computed resistance are investigated. The suggested method is applied to calculate the flow field around a submarine with appendages. The surface triangulations for the hull and the appendages are generated without consideration of each other, then those surface triangulations are simply combined to provide a grid generator with the body boundary. The junctures of the hull and the appendages are identified automatically during the grid generation procedure. Tip vortex is captured, which travels downstream from the tip of the appendages.