• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.4
• /
• pp.585-589
• /
• 2012

The characteristics of interface layer and the effect of mole fraction of inlet gas mixture($B_2H_6/H_2/N_2/TiCl_4$) on the microstructure of Ti(B,N) films were studied by microwave plasma hot filament CVD process. Ti(B,N) films were deposited on a substrate(STD-61) to develop a high performance of resistance wear coating tool. Ti(B,N) films were obtained at a gas pressure of 1 torr, bias voltage of 300 V and substrate temperature of $480^{\circ}C$ in $B_2H_6/H_2/N_2/TiCl_4$gas system. It was found that TiN, $TiB_2$, TiB and hexagonal boron nitride(h-BN) phases exist in thin layer on the STD-61.

• Journal of the Korean Ceramic Society
• /
• v.38 no.1
• /
• pp.34-38
• /
• 2001

Hot filament CVD 방법에서 가스압을 증가시키는 방법을 사용하여 nanocrystalline 다이아몬드 막을 합성하였다. 메탄-수소 혼합가스를 사용하고 메탄함량, 유량, 기판온도합성시간은 각각 4%, 100sccm, 110$0^{\circ}C$, 10시간으로 일정하게 유 였다. 합성 변수로서 가스압을 40 Torr에서 300 Torr 구간에서 변화시켰다. High-resolution SEM으로 막 표면의 형상을 관찰하고, TEM, XRD, micro-Raman spectroscopy를 사용하여 합성된 막의 구조 및 특성을 분석하였다. 합성된 다이아몬드 막은 압력이 높아짐에 따라 mocrocrystalline 다이아몬드 막에서 점진적으로 nanocrystalline 다이아몬드 막으로 변화해갔으며, 가스압에 다라 비다이아몬드 상의 량이 증가하였다. 증착속도는 microcrystalline 다이아몬드 막이 형성되는 구간에서는 압력에 따라 1.1~1.3 $\mu\textrm{m}$/h까지 증가하다가 nanocrystalline 다이아모느 막이 형성되는 구간에서는 압력에 따라 감소하였다. 감소하였다.

• Journal of the Korean Ceramic Society
• /
• v.35 no.11
• /
• pp.1233-1239
• /
• 1998

Gas phase compositions of the hot filament-assisted diamond CVD reaction were analyzed by on-line quadrupole mass analysis(QMA) technique. D2 isotope experiments showed that methance molecules were decomposed into atomic state and then recombined in to acetylene during transport the probe line. Although acetylene or ethylene was supplied instead of methane similar gas compositions were obtained when filament temperature was above 1500$^{\circ}C$ Therefore this system could be assumed near thermal equilibrium state. Filament temperature and reaction pressure variation experiments exhibited the same tendency between acetylene concentration and diamond growth rate and these results implied that acetylene molecule played the role of the reactive species in the diamond CVD reaction.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.05a
• /
• pp.66-67
• /
• 2003

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.1
• /
• pp.6-11
• /
• 2004

The characteristics of interface layer and the effect of bias voltages on the nucleation density and heteroepitaxial growth of diamond films were studied in the hot filament CVD diamond process. Diamond films were deposited on a high speed steel (SKH-51) substrate by bias-assisted hot filament CVD technique with a titanium interlayer. The bias applied for enhancing the emission of electrons from the filament increased the nucleation density and achieving heteroepitaxial growth of CVD diamond. Diamond films obtained at a gas pressure of 20 torr; a bias voltage of 200 V and a substrate temperature of $700^{\circ}C$. Titanium was a suitable element as an interlayer for the diamond deposition on steel because it has high diffusivity of Fe and C as a carbide forming element.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.1
• /
• pp.89-93
• /
• 2012

c-BN films were deposited on SKH-51 steels by electron assisted hot filament CVD method and microstructure development was studied processing parameters such as bias voltage, temperature, etching and phase transformation at boundary layer between BN compound and steel to develop a high performance wear resistance tools. A negative bias voltage higher than 200V at substrate temperature of $800^{\circ}C$ and gas pressure of 20 torr in B2H6-NH3-H2 gas system was one of optimum conditions to produce c-BN films on the SKH-51 steels. Thin layer of hexagonal boron nitride phase was observed at the interface between c-BN layer and substrate.

• Journal of the Korean Ceramic Society
• /
• v.31 no.1
• /
• pp.88-96
• /
• 1994

Hot filament-assisted CVD was carried out to deposit diamond films on Si(100) substrate at 90$0^{\circ}C$ using a 1% CH4-H2 mixture gas. Deposition was made at various conditions of mass flow rate of the feed gas (30~1000 sccm), pressure (2.5~300 Torr), and filament-substrate distance (4~15 mm), and the deposited films were characterized by SEM, XRD, and Raman spectroscopy. As the flow rate increases, the growth rate also increased but the crystallinity of the film was degraded. A longer filament-substrate distance simply caused both the growth rate and the crystallinity to become poorer. On the other hand, the pressure variation resulted in a maximum growth rate of 2.6 ${\mu}{\textrm}{m}$/hr at 10 Torr and the best film quality around 50 Torr, exhibiting an optimum condition. The observed trends were interpreted in terms of the flow velocity-dependent pyrolysis reaction efficiency and mass transport through the boundary layer.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.636-644
• /
• 1997

The effect of various processing parameters, in particular the substrate and filament temperature, on the nucleation of diamond has been studied for the hot filament CVD process with a negative bias on the substrate. As far as the substrate temperature was maintained around the critical temperature of 73$0^{\circ}C$, the nucleation of diamond increased with increasing filament temperature. The maximum nucleation density of ~ 2$\times$109/$\textrm{cm}^2$ was obtained under the condition of filament temperature of 230$0^{\circ}C$, substrate temperature of 75$0^{\circ}C$, bias voltage of 300V, methane concentration of 20%, and deposition time of 2 hours. This nucleation density is about the same as those obtained in previous investigations. For fixed substrate temperatures, the nucleation density varies up to about 103 times depending on experimental conditions. This result is different from that of Reinke, et al. When the substrate temperature was above 80$0^{\circ}C$, a silkworm~shaped carbon phase was co-deposited with hemispherical microcrystalline diamond, and its amount increased with increasing substrate temperature. The Raman spectrum of the silkworm-shaped carbon was the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the deposition condition of diamond, implying that it did not affect the nucleation of diamond.

• Journal of the Korean Ceramic Society
• /
• v.32 no.7
• /
• pp.793-798
• /
• 1995

The relaxation of the intrinsic stresses in the diamond films fabricated by the hot filament CVD was studied, and it was confirmed that the tensile intrinsic stresses in the films could be controlled without any degradation in the quality of the diamond films. The tensile intrinsic stresses in the films decreased from 2.97 to 1.42 GPa when the substrate thickness increased from 1 to 10mm. This result showed that the residual stress was affected by the substrate thickness as well as by the interaction between grains. Applying of ＋50 V between the W filament and the Si substrate during deposition, the tensile intrinsic stress in the film deposited at 0 V was decreased from 2.40 GPa to 0.71 GPa. Such large decrease in the tensile intrinsic stress was due to $\beta$-SiC which acted as a buffer layer for the stress relaxation. However, the application of the large voltage above ＋200V resulted in the change of quality of the diamond film, and nearly had no effect on relaxation in the tensile intrinsic stress.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.550-558
• /
• 1989

Polycrystalline diamond films have been deposited on Si wafer Ly hot W filament CVD method using CH4H2 mixtures. The effects of surface pretreatment, W filament temperature, CH4 volume fraction, and addition of water vapor on the growth rate and morphology of the films were investigated. Surface pretretment was essential for depositing a continuous diamond film. Raising the filament temperature resulted in an increased growth rate and a better crystal quality of the film. As the methane content is varied from 0.5% to 5%, well-faceted crystals gradually transformed into spherical particles of non-diamond phase with a simultaneous increase in the growth rate. Addition of water vapor markedly improved the crystallinity to produce crystalline particles even with 5% methane mixture.