• Geomechanics and Engineering
• /
• v.36 no.1
• /
• pp.39-50
• /
• 2024

Bitumen and high-quality subangular aggregates, the two principal materials used for asphalt concrete construction, are finite and expensive materials. The general availability of crumb rubber and naturally occurring aggregates of different shapes, especially flat and elongated shapes, indicates that they are feasible alternative materials for expanding the volume of bitumen and utilizing a wider range of aggregate shapes for the development of asphalt concrete, with an associated environmental benefit. The study investigated the effect of adding up to 15% crumb rubber and aggregates sorted into different groups, i.e., rounded, elongated, flat, and their combinations, on the rheological and mechanical properties and durability of 50/70 of hot-mix asphalt pavement. The addition of crumb rubber decreased ductility and penetration but increased the softening point. For a 5.5% bitumen content, asphalt concrete briquettes consisting of 7% crumb rubber and three types of aggregate shapes, i.e., 100% rounded, a mix of 75% rounded and 25% elongated, and a mix of 75% rounded, 15% elongated and 10% flat, were associated with high Marshall stability and indirect tensile strength as well as low lateral deformation due to their high solidity and moderate angularity ratio. Also, the addition of 7% crumb rubber resulted in a significant improvement in the tensile strength ratio and rebound strain of briquettes consisting of 75% rounded and 25% elongated aggregates and those with 75% rounded, 15% elongated and 10% flat aggregates. In relation to the parameters investigated, the three groups of briquettes met some of the local (South Africa) requirements for the surface course and base course of low traffic volume roads.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.133-142
• /
• 2011

The objective of this study is to validate the number of gyrations of Superpave gyratory compactor(SGC) for compaction of hot-mix asphalt (HMA) and warm-mix asphalt(WMA) mixtures. Marshall compaction was also used for comparison purpose. The 13mm and 19mm aggregates of 1st class quality shape were used. A PG64-22 and a PG76-22 for HMA and a PG70-22 for WMA. Four compaction temperatures based on the suggested value were used for each binder using 100 gyrations for SGC and 75 blows per side for Marshall compactor. It was found that SGC compaction was somewhat better than Marshall compaction. The analysis of variance showed that two compactors were significantly different in air voids of 19mm mixtures at ${\alpha}=0.05$ level. The 13mm mixture did not show a significant statistical difference. When compacted at the temperature below a certain level, however, the compaction of two compactors were fond to be proor. Therefore, observing compaction temperature above the minimum level is important to secure proper compaction work. If the minimum temperatures were maintained, 100 gyrations, which was given for HMA of arterial road pavement by the Korean Guide, was found to be appropriate compaction, showing similar or better compaction work than 75 blows per side of Marshall compaction.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.167-176
• /
• 2021

When producing recycled asphalt mix, it is important that the old binder of reclaimed asphalt pavement(RAP) should be well melted during blending in the mixer. The recycled asphalt mix is produced by instant mixing(IM) of all materials(RAP, virgin asphalt and new aggregates) all together in the mixer. However, in the same recycled mix, the binder around RAP aggregate was found to show higher oxidation level than the binder coated around the virgin aggregate because the old binder of RAP was not rejuvenated properly while instant mixing. The partially-rejuvenated RAP binder is assumed to be a high stiffness point in IM recycled mix. In this study, the stage mixing(SM) method was introduced; blending RAP and virgin asphalt for the first stage, and then mixing all together with hot new aggregates for the second stage. To compare the effect of the two mixing methods on moisture resistance of recycled mixes, a statistical t-test was performed between SM and IM using indirect tensile strength(ITS) and tensile strength ratio(TSR). Three conditioning methods were used; a 16-h freezing and then 24-h submerging, 48-h submerging, and 72-h submerging in 60℃ water. It was found that the TSR(=ITS_wet/ITS_dry) values of the mixes prepared by SM was clearly higher than the IM mixes, and coefficients of variation of SM mixes were lower than the IM mixes. It was also observed that the ITS_WET of SM was significantly different from the IM at α=0.05 level by statistical t-test. The ITS_WET of SM mix was reduced less than the IM mix in severer conditioned mixes. Therefore, it was concluded that the stage mixing method was an important blending technique for producing better-quality of recycled asphalt mixes, which would show higher moisture resistance than the recycled mixes produced by conventional instant mixing.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.213-224
• /
• 2008

Flexible pavement responses to vehicular loading, such as critical stresses and strains, in each pavement layer, could be predicted by the multilayered elastic analysis. However, multilayered elastic theory suffers from major drawbacks including spatial dimension of a numerical model, material properties considered in the analysis, boundary conditions, and ill-presentation of tire-pavement contact shape and stresses. To overcome these shortcomings, three-dimensional finite element (3D FE) models are developed and numerical analyses are conducted to calculate pavement responses to moving load in this study. This paper introduces a methodology for an effective 3D FE to simulate flexible pavement structure. It also discusses the mesh development and boundary condition analysis. Sensitivity analyses of flexible pavement response to loading are conducted. The infinite boundary conditions and time-dependent history of calculated pavement responses are considered in the analysis. This study found that the outcome of 3D FE implicit dynamic analysis of flexible pavement that utilizes appropriate boundary conditions, continuous moving load, viscoelastic hot-mix asphalt model is comparable to field measurements.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3296-3301
• /
• 2011

The Porous pavement gains popularity because of several benefits. It is to minimize hydro-planning condition, spraying condition, and splash to increase friction resistance, and decrease noise. Also, other studies showed that it is important to have appropriate porosity to reduce noise and water flush. The purpose of this study is an evaluation on the mechanical properties of asphalt pavements for surface course. In this study the specimen was manufactured using the Gyratory compactor in order to compact the strengthened surface course that involved the two-layer pavement. This study is conducted by using Marshall stability test(KS F 2377), Impact resonance test, Schmidt hammer test(KS F 2730), and the Uniaxial compression test(KS F 2314). Using the Uniaxial compression test and Schmidt hammer test, the values of compressive strength and bearing capacity were measured, and the modulus of elasticity for each specimen was respectively measured using the Uniaxial compression test, Impact Resonance test.

• International Journal of Highway Engineering
• /
• v.18 no.3
• /
• pp.1-9
• /
• 2016

PURPOSES : This study aims to show the difference of the binder aging level in the hot-mix asphalt (HMA) mixture after short-term aging (SA) under different aging conditions, such as mixture temperature and duration in hour. METHODS : Three SA times (i.e., 1 h, 2 h, and 4 h) at two temperatures (i.e., $160^{\circ}C$ and $180^{\circ}C$) were used for the normal mixtures prepared using a PG64-22 asphalt. The field long-term aging (LA) was simulated by applying the same LA procedure (65 h at $110^{\circ}C$) to all compacted specimens, prepared at the air void of 7% using each SA-treated mixture, in a convection oven. The binder aging level was measured in terms of large molecular size by gel-permeation chromatography (GPC) from the mixture and the absolute viscosity (AV) from the recovered binder. The aging levels were evaluated using those two properties after SA and LA, and then compared based on the normal SA (NSA) mixture (1 h at $160^{\circ}C$). The service life reduction caused by SA in various conditions was estimated based on the aging level of the field cores from different locations in various service lives. RESULTS : The results of the laboratory evaluation indicated that the binder of the mixture, which was treated at longer SA time and higher temperature, showed a significantly higher aging level than the NSA mixture. The binder aging level from a longer time, such as 2 h and 4 h SA, or at a higher temperature ($180^{\circ}C$), were estimated to be similar to that of the mixtures, which had already been in field service for several years. CONCLUSIONS : The HMA mixture should be produced at a moderate temperature, such as $160^{\circ}C$, and placed within a limited hauling and queuing time to avoid a significant short-term aging of the binder before placement in the field pavement. The SA for a longer time at a higher temperature than the NSA condition was found to be detrimental to the service life of the asphalt pavement.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.139-145
• /
• 2011

The practice of asphalt pavement recycling has grown rapidly over the decade, one of which is the cold in-place recycling with the foamed asphalt (CIR-foam) or the emulsified asphalt (CIR-emulsion). Particularly, in Iowa, the CIR has been widely used in rehabilitating the rural highways because it significantly increases the service life of the existing pavement. The CIR layer is typically overlaid by the hot mix asphalt (HMA) to protect it from water ingress and traffic load and obtain the required pavement structure and texture. Most public agencies have different curing requirements based on the number of curing days or the maximum moisture contents for the CIR before placing the overlay. The main objective of this study is to develop a moisture loss index that the public agency can use to monitor the moisture content of CIR layers in preparation for a timely placement of the wearing surface. First, the moisture contents were measured in the field using a portable time domain reflectometry (TDR) device. Second, the weather information in terms of rain fall, air temperature, humidity and wind speed was collected from the same location. Finally, a moisture loss index was developed as a function of initial moisture content, air temperature, humidity and wind speed. The developed moisture loss index based on the field measurements would help the public agency to determine an optimum timing of an overlay placement without continually measuring moisture conditions in the field.

• International Journal of Highway Engineering
• /
• v.7 no.1 s.23
• /
• pp.63-71
• /
• 2005

Asphalt binder grading is to specify quality of asphalt binders relating to pavement performance in orderly manner, and provides the necessary information in selecting the appropriate asphalt binder for the hot mix design. For this purpose, United States has developed the PG-grading in 1995 and is implementing in practice. Recently, this American PG-grading system has been accepted as the domestic binder grading specification. However, the Asian (including Japan and China) and the most European countries are still use the traditional penetration and viscosity specification. The goal of this study lies in analysing the American PG-grading for its justification. As the result, the serious errors are found, and thus, to eliminate the errors, the more precise binder grading equation is introduced, Credibility of this study is checked by predicting the literature rut data with the equations mentioned. The prediction result are validating the claimes made in this study.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.3
• /
• pp.947-954
• /
• 2014

In general, Fracture of the material is not occurring of the maximum normal stress or the maximum shear stress failure in the state. Maximum normal stress and maximum shear stress in the state of Critical coupling from being destroyed based on the Mohr-Coulomb theory. Couple of different mixtures, including permeable asphalt pavement, SMA and dense-graded asphalt mixture, were used for compression triaxial test at $45^{\circ}C$ and $60^{\circ}C$. Mohr-Coulomb theory to the analysis of compression triaxial test result of the internal friction angle $38.9^{\circ}{\sim}46.9^{\circ}$ measured somewhat irregularly, but in the case of cohesion, depending on whether the temperature and immersion of the specimen appeared differently. In addition, Indirect tensile test and compression triaxial test of the asphalt mixture to determine the correlation between compression triaxial test results assessed as cohesion and internal friction angle calculated using the theoretical Indirect tensile strength and measured indirectly tensile strength were analyzed. The Measured & Predicted IDT St values tended to be proportional.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.146-152
• /
• 2018

In this study, to improve the performance of asphalt mixtures for plastic deformation occurring mainly in Korea, complex modifiers were prepared by mixing powders and liquid type modifiers. The main constituents were powdery diatomaceous earth, mica and carbon black, and liquid type solid 70% SBR latex. The tensile strength ratios for the two asphalt mixtures used in the test were above 0.80 for the Ministry of Land Transportation (2017) asphalt mixture production and construction guidelines. The effects of increasing the tensile strength in the dry state was more than 14% when the composite modifier was added. The deformation rate per minute by the wheel tracking test load was an average of 0.07 to 0.147 for each mixture. The strain rate per minute was improved by the modifier, and the dynamic stability was improved by almost 100% from 295 to 590. In addition, the final settling was reduced from 11.38 mm to 9.57 mm. A plastic deformation test using the triaxial compression test showed that the amount of deformation entering the plastic deformation failure zone at the end of the second stage section and in the third stage plastic deformation section was 1.76 mm for the conventional mixture and 1.50 mm for the complex modifier mixture. The average slope of the complex modifier asphalt mixture mixed with the multi-functional modifier was 0.005 mm/sec. The plastic deformation rate is relatively small in the section where the road pavement exhibits stable common performance, i.e. the traffic load.