• Fibers and Polymers
• /
• 제4권4호
• /
• pp.199-203
• /
• 2003

In order to investigate the effects of cross-sectional shapes on the sound characteristics of polyester fibers, 10 specimens were woven into a twill structure made of round, hollow, triangular, u-shape, cruciform, and composite cross-sectional (▲/▲ ,()/▲, Y/Y) fibers. Their rustling sounds were recorded, and their sound spectra were obtained from FFT analysis. Physical sound parameters (LPT, ΔL, Δf) and Zwicker's psychoacoustic parameters of the loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z) were calculated from the sound spectra. According to noncircular cross-section fibers, the hollow shaped fiber had the highest value of LPT, ΔL, loudness(Z), and fluctuation strength(Z). The triangular shaped fiber had a lower value of LPT, ΔL, loudness(Z), and roughness(Z) than those of the round shaped fiber. Among composite cross-section fibers, C1(▲/▲) and C3 (Y/Y) had higher values of LPT, ΔL, Δf and loudness(Z) but C2(()/▲) had lower values. Also the LPT, ΔL, sharpness(Z), and roughness(Z) values of different denier were similar to each other, but the Δf and loudness(Z) values increased as the denier increased.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권1호
• /
• pp.45-52
• /
• 2015

섬유복합체 (Fiber Reinforced Polymer, FRP)는 비강도가 높고, 비부식성 재료라는 특징을 가지고 있어서 건설 분야에서 철근을 대체할 수 있는 보강근 재료로 인식되고 있다. 몇몇 유리섬유 복합체 (Glass FRP, GFRP) 보강근이 상용화되어 있지만 GFRP는 철근에 비해 가격이 비싸고 상대적으로 낮은 탄성계수와 취성 파괴 특성 때문에 다소 경쟁력이 떨어진다. GFRP 보강근의 재료가격을 낮출 수 없다면 사용된 재료의 성능을 최대로 하여 보강근의 성능을 높이는 것이 상대적인 가격을 낮추는 방법이 될 수 있다. 일반적으로 FRP 보강근의 직경이 커질수록 인장강도는 감소하는 것으로 알려져 있다. 이의 원인 중 하나는 보강근이 인장을 받을 때 외력이 중앙에 위치한 섬유에 충분히 전달되지 못하여 외측에 위한 섬유들만이 인장에 저항하기 때문이다. 따라서 본연의 역할을 수행하지 못하는 섬유는 제거함으로써 보강근의 단가를 낮추면서 보강근이 소정의 성능을 발휘하도록 한다면 가격대비 성능이 최적화된 FRP 보강근을 제작할 수 있다. 본 연구에서는 직경 19 mm의 GFRP 보강근에 대해 단면 내에 중공이 존재하는 경우 중공비율에 따른 인장특성의 변화를 실험적으로 관찰하였다. 중공이 없는 GFRP 보강근 세 개, 네 가지 중공비율에 대해 각각 여섯 개의 GFRP 보강근 시편을 준비하여 인장실험을 실시하였으며 결과 분석을 통하여 인장특성 변화를 도출하였으며 이를 바탕으로 최적의 중공비율을 제안하였다.

• The Korean Journal of Ceramics
• /
• 제4권3호
• /
• pp.171-175
• /
• 1998

$Al_2O_3$-TiC composites were prepared from aluminum, titanium oxide, and carbon fibers by self-propagating high-temperature synthesis(SHS). After the SHS reaction, the TiC phase in the sample was found either fibrous or non-fibrous shape. The fraction of the fibrous TiC phase varied with the amount of $Al_2O_3$ diluent addition. The optimum amount of diluent to make fibrous carbide was determined to be 30%. The fibers were hollow inside and made of multiple grains with a composition of titanium carbide. The hollow fiber formation mechanism was suggested and discussed. The synthesized powders were consolidated to dense composites by hot pressing at $1750^{\circ}C$ under 30 MPa.

• KSBB Journal
• /
• 제7권1호
• /
• pp.67-71
• /
• 1992

50개의 폴리프로필렌 실관과 3개의 테르폰 실관으로 구성된 실관반응기에서 Saccharomyces cerevisiae효모를 이용하여 알콜의 연속 생산을 연구하였다. 생산된$CO_2$는 테프론 실관으로 내어 보냈고 과잉효모 세포는 shell-side를 통하여 제거하였다. Shell-side 부피를 기준으로 세포농도는 266g/L였고 알콜 생산성은 205g/L를 얻었다. 질소 결핍배지를 사용했을 경우 생산성이 너무 낮아 실제 응용할 가치는 없었다.

• Carbon letters
• /
• 제18권
• /
• pp.18-23
• /
• 2016

Polyacrylonitrile (PAN)-based carbon fibers have high specific strength, elastic modulus, thermal resistance, and thermal conductivity. Due to these properties, they have been increasingly widely used in various spheres including leisure, aviation, aerospace, military, and energy applications. However, if exposed to air at high temperatures, they are oxidized, thus weakening the properties of carbon fibers and carbon composite materials. As such, it is important to understand the oxidation reactions of carbon fibers, which are often used as a reinforcement for composite materials. PAN-based carbon fibers T300 and T700 were isothermally oxidized in air, and microstructural changes caused by oxidation reactions were examined. The results showed a decrease in the rate of oxidation with increasing burn-off for both T300 and T700 fibers. The rate of oxidation of T300 fibers was two times faster than that of T700 fibers. The diameter of T700 fibers decreased linearly with increasing burn-off. The diameter of T300 also decreased with increasing burn-off but at slower rates over time. Cross-sectional observations after oxidation reactions revealed hollow cores in the longitudinal direction for both T300 and T700 fibers. The formation of hollow cores after oxidation can be traced to differences in the fabrication process such as the starting material and final heat treatment temperature.

• 한국환경과학회지
• /
• 제9권2호
• /
• pp.173-176
• /
• 2000

This study was carried out to investigate the filtration characteristics of membrane modules according to hollow fiber dispersion for direct solid-liquid separation of activated sludge. 2 bundle, 4 bundle, and 10 bundle, and 10 bundle module used in this experiment according to hollow fiber dispersion was manufactured at laboratory and permeate flux and transmembrane pressure(TMP) of each module were observed under a suction pressure of 0.5kgf/c$m^2$. As the hollow fibers were dispersed, permeate flux was increased and TMP was decreased. Permeate flux and TMP of each module was 15.0 $\ell$/$m^2$.h and 31.8 cmHg for 2 bundle, 16.0 $\ell$/$m^2$ .h and 17.4 cmHg for 4 bundle, and 20.4 $\ell$/m2 .h and 31.8 cmHg for 10 bundle. In conclusion, the membrane fouling is expected to be decrease by maintaining lower TMP with hollow fiber dispersion.

• Current Optics and Photonics
• /
• 제6권2호
• /
• pp.143-150
• /
• 2022

Anti-resonant hollow-core photonic crystal fiber (AR-HCF) has unique advantages, such as low nonlinearity and high damage threshold, which make it a promising candidate for high-power laser delivery at distances of tens of meters. However, due to the special structure, optical properties such as mode-field profile and bending loss of hollow-core fibers are different from those of solid-core fibers. These differences have limited the widespread use of AR-HCF in practice. In this paper we conduct numerical analysis of AR-HCFs with different structural parameters, to analyze their influences on an AR-HCF's optical properties. The simulation results show that with a 23-㎛ air-core diameter, the fundamental mode profile of an AR-HCF can well match that of the widely used Nufern's 20/400 fiber, for nearly-single-mode power delivery applications. Moreover, with the ratio of cladding capillary diameter to air-core diameter ranging from 0.6 to 0.7, the AR-HCF shows excellent optical characteristics, including low bending sensitivity while maintaining single-mode transmission at the same time. We believe these results lay the foundation for the application of AR-HCFs in the power delivery of high power fiber laser systems.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 1999년도 봄 학술발표회 논문집
• /
• pp.241-244
• /
• 1999

• 한국막학회:학술대회논문집
• /
• 한국막학회 2002년도 춘계 총회 및 학술발표회
• /
• pp.172-173
• /
• 2002

• 한국세라믹학회지
• /
• 제50권4호
• /
• pp.301-307
• /
• 2013

SiC hollow fiber was fabricated by curing, dissolution and sintering of Al-PCS fiber, which was melt spun the polyaluminocarbosilane. Al-PCS fiber was thermally oxidized and dissolved in toluene to remove the unoxidized area, the core of the cured fiber. The wall thickness ($t_{wall}$) of Al-PCS fiber was monotonically increased with an increasing oxidation curing time. The Al-PCS hollow fiber was heat-treated at the temperature between 1200 and $2000^{\circ}C$ to make a SiC hollow fibers having porous structure on the fiber wall. The pore size of the fiber wall was increased with the sintering temperature due to the decomposition of the amorphous $SiC_xO_y$ matrix and the growth of ${\beta}$-SiC in the matrix. At $1400^{\circ}C$, a nano porous wall with a high specific surface area was obtained. However, nano pores grew with the grain growth after the thermal decomposition of the amorphous matrix. This type of SiC hollow fibers are expected to be used as a substrate for a gas separation membrane.