• 대한조선학회논문집
• /
• 제41권6호
• /
• pp.15-23
• /
• 2004

In order to investigate efficiency and flowfield charateristics of the intake-diffuser for the ship waterjet propulsion, new experimental verification technology was set up in the cavitation tunnel. 1-hole and 5-hole pilot tubes were designed and manufactured to measure the pressure and velocity distributions at intake-diffuser entrance and impeller inlet. The calibration of the 5-hole pilot tubes is conducted at the cavitation tunnel The cavitation inception occurs at the intake lip, and the occurrence position depends on IVR (Inlet Velocity Ratio) condition. The present experimental device will be applied sufficiently for the development of the design and performance improvement technologies.

• Journal of information and communication convergence engineering
• /
• 제8권3호
• /
• pp.273-276
• /
• 2010

Opportunistic spectrum access (OSA) allows unlicensed users to share licensed spectrum in space and time with no or little interference to primary users, with bring new research challenges in MAC design. We propose a cognitive MAC protocol using statistical channel information and selecting appropriate idle channel for transmission. The protocol based on the CSMA/CA, exploits statistics of spectrum usage for decision making on channel access. Idle channel availability, spectrum hole sufficiency and available channel condition will be included in algorithm statistical information. The model include the control channel and data channel, the transmitter negotiates with receiver on transmission parameters through control channel, statistical decision results (successful rate of transmission) from exchanged transmission parameters of control channel should pass the threshold and decide the data transmission with spectrum hole on data channel. The proposed protocol's simulation will show that proposed protocol does improve the throughput performance via traditional opportunistic spectrum access MAC protocol.

• Composites Research
• /
• 제29권6호
• /
• pp.388-394
• /
• 2016

Fiber reinforced plastic (FRP) composites have drawn increasing attentions worldwide for decades due to its outstanding properties. Stress concentration factor (SCF) as an essential parameter in materials science are critically considered in structure design and application, strength assessment and failure prediction. However, investigation of stress concentration in FRP composites has been rarely reported so far. In this study, three resource-conserving analyses (Isotropic analysis, Orthotropic analysis and Finite element analysis) were introduced to plot the $K_T^A-d/W$ curve for E-glass/epoxy composite plate with the geometrical defect of circular hole placed centrally. The plates were loaded to uniaxial direction for simplification. Finite element analysis (FEA) was carried out via ACP (ANSYS composite prepost module). Based on the least squares method, a simple expression of fitting equation could be given based on the simulated results of a set of discrete points. Finally, all three achievable solutions were presented graphically for explicit comparison. In addition, the investigation into customized efficient SCFs has also been carried out for further reference.

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.130-136
• /
• 1998

A procedure of stress and strength analysis has been proposed for the centrifuge rotor of composite materials of quasi-isotropic laminates. The goal in this study is to maximize the allowable rotating speed, that is, to minimize maximum strength ratio with the given path length by changing the geometric parameter-outer radius and ply angles in quasi-isotropic laminates. Optimum values of the geometric parameter-outer radius and ply angles are obtained by multilevel optimization. All the geometric dimensions and stresses are normalized such that the result can be extended to a general case. Two dimensional analysis at each cross section with an elliptic tube hole subjected to internal hydrostatic pressures by samples as well as the centrifugal body forces has been performed along the height to calculate the stress distribution with the plane stress assumption, and Tsai-Wu failure criterion is used to calculate the strength ratio. The maximum allowable rotating speed can be increased by changing the radii of the outer surface along the height with the maximum strength ratio under the unit value : The optimal number of ply angles maximizing the allowable rotating speed in quasi-isotropic laminates is found to be the half number of tube hole, and the optimal laminate rotation angle is the half of $[{\pi}/m]$. A $[{\pi}/3]$ laminate, for instance, is stronger than a $[{\pi}/4]$ laminate for the centrifuge rotor of 6 tube hole number even though they have the same stiffness.

• 한국지반신소재학회논문집
• /
• 제15권4호
• /
• pp.43-52
• /
• 2016

본 논문에서는 지반 시추 시 공벽붕괴 방지를 위해 사용되는 안정액의 다양한 배합비에 따른 공학적 특성에 대한 실험적 연구를 다루었다. 이를 위해 먼저 배합수가 청수일 경우, 안정액의 공학적 특성을 검토하였으며 아울러 해수 배합시 안정액의 공학적 성능 변화에 대한 공학적 특성을 분석하였다. 그 결과, 청수에서 벤토나이트와 폴리머를 추가할 경우 공학적 성능이 향상되는 것으로 나타났으며, CMC에 비해 Polymer의 증점 효과가 우수한 것으로 검토되다. 또한 해수의 경우 벤토나이트에 비해 내염성점토의 내염성 성능이 우수한 것으로 검토되었다. 따라서 본 논문에서는 시공시 배합수에 따른 안정액을 성능에 대한 정성적인 결과를 제시하였다.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.180-186
• /
• 2011

This paper describes a micro electrical discharge machining (MEDM) technique that uses an insulated tool in combination with ultrasonic vibration to drill micro holes. As the machining depth becomes deeper, the dispersion of debris and circulation of the dielectric fluid are difficult to occur. Consequently, machining becomes unstable in the machining region and unnecessary electrochemical dissolution and secondary discharge sparking occur at the tool side face. To reduce the amount of unnecessary side machining, an insulated tool was used. Ultrasonic vibration was applied to the MEDM work fluid to better remove debris. Through these methods, a $1000\;{\mu}m$ thick stainless steel plate was machined by using a $73\;{\mu}m$ diameter electrode. The diameters of the hole entrance and exit were $96\;{\mu}m$ and $88\;{\mu}m$, respectively. It took only 351s to completely drill one hole.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.769-775
• /
• 2008

The objective of this report is to determine the difference of thermal response that grouted two different materials, and compare the simulation result of the length of total ground heat exchanger length that using the ground thermal conductivity. And also to know heat exchange variation of ground heat exchanger temperature that measured with various test depth. The result shows that the test hole grouted with water permeable material got better thermal response than grouted with water impermeable material. However, with consideration of ingnore for the initial 12 hour data, the test hole grouted with impermeable material has larger thermal conductivity than the other. By former thermal conductivity, simulated data by engineering program shows only 3.4% difference or less. This result shows that ground thermal conductivity is not the main variables for the design program of ground heat exchanger. At the cooling or heating mode, base on the depth of -150m, the ground heat exchanger has best temperature at $-90{\sim}-60m$ and than getting worse because of entering water heat exchanged with leaving water in the same hole.

• 대한조선학회지
• /
• 제8권1호
• /
• pp.53-66
• /
• 1971

The effect of reinforced circular hole in a flat plate under general biaxial loading conditions is considered. The reinforcement is achieved by attaching a circular ring of uniform rectangular cross section along the boundary of the hole. This investigation includes a theoretical solution and an experimental conformation. In the theoretical analysis, Gurney's method is used to obtain a solution for the stress distribution and the solution is expressed in a general form, so that it can be applicable to the case of general biaxial loading and general values of Poisson's ratios. In the experimental work a systematic series of photoelastic models, as shown in Fig.5 and Table 1, were analyzed on polariscope. The experimental results were in good agreement with the theoretical ones, as shown in Fig.8 and 9. The conclusions derived are as follows: 1) The theoretical results, given in Eq. $(1){\sim}(5)$, are sufficient in accuracy for the engineering design purpose. 2) The stress concentration factor decreases as the ratio n increases, but not significant beyond n=3. 3) The stress concentration factor increase as the ratio m increases, but not significant below m=0.7.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2012년도 추계학술대회
• /
• pp.125-127
• /
• 2012

With the progress of electronics and radio communication technology, human enjoys greater freedom in communication. However, EMW (Electro-Magnetic wave) environments have became complicate and more difficult to control. Thus, international organizations, such as the American National Standard Institution (ANSI), Federal Communications Commission (FCC), the Comite Internationale Special des Perturbations Radio electrique (CISPR), etc, have provided standard for controlling the EM wave environments and for the countermeasure of the electromagnetic compatibility (EMC). In this paper, the status of EMW absorber and the goal of smart EMW absorber ifor the future were described. Furthermore, design method of the smart EM wave Absorber with heat radiating function was suggested. The designed smart EM wave Absorber has the absoption ability of more than 5 dB from 2 GHz to 2.45 GHz band, one optimum aperture (hole) size of which was 6 mm, 9 mm in adjacent hole space, and 6.5 mm in thickness, respectivly. Thus, it is repected that these results can be applied to various EMC devices in electronic, communication, and controlling systems.

• 한국의류학회지
• /
• 제26권1호
• /
• pp.74-82
• /
• 2002

본 연구에서는 서열환경하에서의 안전모 착용과 관련된 생리학적 온열반응을 조사하고 아울러 일반적인 안전모에 통풍을 목적으로 구멍을 뚫어 놓은 안전모가 작업시 체열방산, 체온의 항상성과 같은 생리반응에 어떠한 영향을 미치는지에 대한 검토를 실시하고자 성인 남자 5명을 대상으로 착용실험을 실시하였다. 구멍이 없는 일반적인 형태의 무공 작업 안전모와 통기를 목적으로 구멍을 뚫어 놓은 유공 작업 안전모를 대조군으로 하여, 온도 30$\pm$1$^{\circ}C$, 습도 55$\pm$10%R.H의 인공기후실에서 휴식과 운동을 되풀이하는 총70분간의 실험을 실시하였다. 그 결과를 요약하면 다음과 같다. 1. 직장온과 심박수는 유공안전모 착용시가 무공안전모 착용시 보다 유의하게 낮게 나타났으며, 체열평형과 관련하여 신체기능의 항상성을 유지하는 데에 유공안전모를 착용하는 것이 더 효율적임을 알 수 있었다. 2.각 부위의 피부온과 평균 피부온은 유공안전모 착용시가 무공안전모 착용시보다 유의하게 낮았는데 특히 발한이 다른 부위보다 먼저 시작되는 이마에서 더욱 두드러지게 나타났다. 이는 안전모 착용으로 체온이 상승되어 피부온과 평균 피부온의 상승으로 이어지는 과정에서 유공안전모 착용시 가 무공안전모 착용시보다는 더 유리하다는 것을 알수 있었다. 3. 혈압은 전 구간에 걸쳐 유공안전모 착용시가 무공 안전모 착용시 보다 낮게 나타났다. 유공안전모 착용시가 무공안전모 착용시 보다 혈액을 통해 전달되는 체열의 상승이 억제되고 피부온과 심박수의 상승이 억제되는 것을 알수 있었는데 이것이 곧 혈압의 과다상승 방지와 인체부담의 경감으로 연결되었다고 사료된다. 4. 발한량은 유공안전모 착용시가 무공안전모 착용시보다 낮은 값을 나타내 보였다. 운동으로 인해 높아진 머리부분의 온도는 통풍을 목적으로 구멍을 뚫어 놓은 유공안전모를 착용했을 때 통기구멍으로 공기가 순환되어 온도가 과도하게 상승하는 것이 방지된다. 따라서 서열환경하에서의 체온상승이 억제됨에 따라 낮은 발한량을 나타내 보였다. 안전모내의 기후에서 유공안전모 착용시가 무공안전모 착용시보다 유의하게 더 낮은 온도를 나타내었고, 안전모내 습도는 운동시에 유공안전모 착용시가 무공안전모 착용시보다 다소 낮은 경향을 보였다. 통기를 목적으로 구멍을 뚫어 놓은 유공안전모를 착용함으로 인해 모자내의 더운 공기가 외부와 순환되어 무공안전모 착용시 보다는 온도가 낮게 나타났고 땀이 유공안전모의 구멍을 통해 증발을 일으켜 과도하게 습해지는 것을 방지 할 수 있었다. 5. 주관적 감각으로 온냉감, 습윤감, 쾌적감, 피로감을 측정하였는데 유공안전모 착용시가 무공안전모 착용시보다 더 낮은 주관적 감각 수치를 나타내어 착용감이 더 좋았음을 알 수 있었다. 또한 근력측정에서 무공안전모 착용시가 유공안전모 착용시 보다 평가 수치 가 낮게 나타나 더 피로한 것을 알수 있다. 이상의 결과에서 통기를 목적으로 구멍을 뚫어놓은 유공작업안전모가 심부온, 피부온, 혈압, 심박수, 발한량, 모자내 기후 등의 인체생리반응을 고려해 볼 때 더 바람직한 작업 안전모 형태라는 것을 알 수 있었다. 종래의 작업과 관련한 피복연구에서 작업복, 장갑, 신발에 대하여는 생리학적 연구가 이루어졌으나, 안전모에 관한 연구에서는 생리학적인 부분을 고려하지 않고 단지 안전 보호측면에서의 연구가 이루어졌을 뿐이었다. 따라서 서열환경하에서 머리부분의 쾌적성을 고려한 다양한 작업 안전모에 대한 계속적인 연구와 개발이 이루어진다면 물리적 측면에서 작업 안전을 만족시킬 뿐만 아니라 생리적 측면에서 체열 평형을 도모하여 작업 능률의 향상을 가져올 것이다.