• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.6
• /
• pp.897-908
• /
• 2019

The objective of this study is to evaluate the field support performance of highperformance lattice girder (BK-Lattice Girder) by using numerical analysis. Three types (50, 70, 95-type) of existing and high performance lattice girders were applied to the cross section of highway 2, 3, and 4 lane tunnels to compare the supporting performance. The numerical analysis was the finite element method and the lattice girder was modeled in three dimensions with an elasto-plastic frame. The ground was modeled as a spring receiving only compression. The load was applied as a concentrated load on the central ceiling of the tunnel section. The yield strengths of the lattice girders were determined from the numerical results to compare the supporting performance of lattice girder. In case of 50-type, the yield strengths of high-performance lattice girders were increased by 6.7~10.0% compared with those of the existing lattice girders. In the case of 70-type, the high-performance lattice girders increased yield strengths by 12.1~14.9% than the existing lattice girder. In the case of 95-type, the high-performance lattice girders increased yield strengths by 13.3~20.0% than the existing lattice girder. As a result of numerical analysis, it was considered that the high-performance lattice girder supported better than the existing lattice girder when only the lattice girders were constructed.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.1
• /
• pp.13-22
• /
• 2009

The study area is a tunnelling section passing through the Yangsan Fault zone. Kyungbu express highway and national road 35 are located above the tunnel. Previous study showed that fault gouge and fault breccia were widely distributed in the tunnelling section with a maximum width of 100 m. From the present study, it is found that sedimentary rocks consisting mainly of shale are distributed at the eastern block of the Yangsan Fault and these rocks are not subject to mechanical fracturing and hydrothermal alteration. On the other hand, dacitic tuff distributed at the western block of the Yangsan Fault is largely affected by mechanical fracturing and hydrothermal alteration. The large fault zone of $50{\sim}130m$ width was formed by complex processes of mechanical fracturing and hydrothermal alterations such as chloritization, sericitization, and kaolinization. Based on the characteristics of mechanical fracturing and hydrothermal alterations, the Yangsan fault zone in the study area is geotechnically classified as four zones: unaltered zone, altered zone, altered fractured zone, and fault gouge zone. These zones show different degrees and aspects in mechanical fracturing and hydrothermal alterations, resulting in different engineering properties.

• Economic and Environmental Geology
• /
• v.39 no.4 s.179
• /
• pp.441-450
• /
• 2006

The on-land seismic survey in Korea was begun in mid-1960s. Kim et al.(1967) of Korea Geological Survey reported on the result of gravity and seismic reflection surveys conducted in the Pohang area for the period of 1963-64 to assess its possibility of oil entrapment. Hyun and Kim (1966) carried out a refraction survey on the tunnel wall. Since then, the KGS geophysicists had conducted seismic surveys on Kyungsang sedimentary basin as a main project for several years. In 1970s, on-land seismic surveys had been conducted for various purposes such as site investigation for the nuclear power plants and industrial complex, exploration for ground water, mineral resources and underground tunnel. The first reflection survey with CMP acquisition was attempted in 1978 by using a digital recording system. But most of on-land seismic surveys had employed the refraction method until 1980s. In 1990s, high resolution reflection and various borehole seismic surveys such as tomography, uphole, downhole, cross-hole methods have been attempted by universities and engineering companies. The applications of on-land seismic surveys have been enlarged for both academic and industrial purposes such as investigation of geologic structure of the fault and tidal flat area, construction of highway, railroad and dam, geothermal energy and mineral resource exploration, environmental assessment for waste disposal sites and archaeological investigations. In 2002, the first crustal seismic survey was carried out on the profile of 294km length across the whole peninsular. It is expected that the advanced technology and experience acquired through offshore seismic surveys, which have been conducted in continental shelf of Korea and foreign oil fields, will stimulate the more active on-land seismic explorations.

• Structural Engineering and Mechanics
• /
• v.86 no.5
• /
• pp.607-619
• /
• 2023

This study, it was tried to evaluate the asphalt behavior under tensile loading conditions through indirect Brazilian and direct tensile tests, experimentally and numerically. This paper is important from two points of view. The first one, a new test method was developed for the determination of the direct tensile strength of asphalt and its difference was obtained from the indirect test method. The second one, the effects of particle size and loading rate have been cleared on the tensile fracture mechanism. The experimental direct tensile strength of the asphalt specimens was measured in the laboratory using the compression-to-tensile load converting (CTLC) device. Some special types of asphalt specimens were prepared in the form of slabs with a central hole. The CTLC device is then equipped with this specimen and placed in the universal testing machine. Then, the direct tensile strength of asphalt specimens with different sizes of ingredients can be measured at different loading rates in the laboratory. The particle flow code (PFC) was used to numerically simulate the direct tensile strength test of asphalt samples. This numerical modeling technique is based on the versatile discrete element method (DEM). Three different particle diameters were chosen and were tested under three different loading rates. The results show that when the loading rate was 0.016 mm/sec, two tensile cracks were initiated from the left and right of the hole and propagated perpendicular to the loading axis till coalescence to the model boundary. When the loading rate was 0.032 mm/sec, two tensile cracks were initiated from the left and right of the hole and propagated perpendicular to the loading axis. The branching occurs in these cracks. This shows that the crack propagation is under quasi-static conditions. When the loading rate was 0.064 mm/sec, mixed tensile and shear cracks were initiated below the loading walls and branching occurred in these cracks. This shows that the crack propagation is under dynamic conditions. The loading rate increases and the tensile strength increases. Because all defects mobilized under a low loading rate and this led to decreasing the tensile strength. The experimental results for the direct tensile strengths of asphalt specimens of different ingredients were in good accordance with their corresponding results approximated by DEM software.

• Tunnel and Underground Space
• /
• v.17 no.4
• /
• pp.322-331
• /
• 2007

Hundreds of rock slopes are constructed along the road, highway and railroad in mountainous Kangwon province and managed by each authorities concerned. It is practically not possible to carry out detailed rock slope investigation owing to the tremendous number of slopes and budgetary limit. Therefore, it is reasonable to perform a step-by-step investigation consisted of basic and detailed survey program and practical rock slope hazard assesment method for person in charge is strongly required. Through the development and application of KSMR (Korean Slope Mass Rating), it was found that KSMR could be practically used as an alternative of SMR though the number of inputs were reduced. In addition, the difference of hazard assessment between KSMR and experts decreased in case of considering the height of slope.

• International Journal of Highway Engineering
• /
• v.7 no.4 s.26
• /
• pp.173-184
• /
• 2005

Pavement markings delineate driver's sight and attentions at day and night. Retroreflectivities of the pavement markings are known to be affected by some factors such as geometrical characteristics of road sections, marking materials, traffic volumes, weather, and so on. Therefore, pavement markings would have different retroreflectivities place by place. The objective of this paper is to contend that there are rises and falls of retroreflectivity of specific geometrical characteristics of road section based on observed field data. For this purpose, retroreflectivities of yellow continued lines and white skip lines were measured on the freeway sections from Hanam to Nami interchanges. And then, the sections are categorized based on road geometric or facility types. From this study, it may be concluded that there exist considerably lower retroreflectivity trends of pavement markings at sharply curved sections, climbing lane sections, ramp sections, and tunnel sections than averaged retroreflectivity trends on freeway sections. This may leads to the necessity of differential pavement marking managements.

• Tunnel and Underground Space
• /
• v.24 no.4
• /
• pp.275-281
• /
• 2014

The performance criteria of rockfall protection fence and reliability index were investigated considering characteristic of rockfall energy occurred at 160 cut slopes in national highway. As a result of study on statistic of variables that decide rockfall energy using Monte-Carlo simulation, the degree of slope was normal distribution type, mass of rockfall and height of slope was lognormal distribution type. The rockfall energy follows lognormal distribution because of statistical characteristic of mass of rockfall. The reliability index of rockfall protection fence was 0.678 and the failure probability of was very high as 24.9%. Proposed performance criteria of rockfall protection fence considering the scale of domestic rockfall energy is maximum 500 kJ and the range of reliability index was from 1.028 to 1.956. the failure probability of rockfall protection fence was from 14.8 to 2.5 percent if applying the performance criteria using the reliability index.

• Tunnel and Underground Space
• /
• v.11 no.3
• /
• pp.206-216
• /
• 2001

Many failures in cut slopes occur during and following road construction. Failures are caused, in part, by a lack of understanding of the characteristics of rock mass including its geologic structure. The stability of rock slopes is closely related to factors that include the type of rock, development of geological structures, weathering, characteristics of rock, and the shape of the geologic features. Therefore, it is very important to consider these characteristics of rock mass in the evaluation of rock slope stability. In spite of investigation from many slope failures, these information data were not systematically stored and not efficiently utilized. In this study, a Database system named DB/SLOPE was developed using Oracle for systematic management of cut slopes. The developed database system can be used to estimate of slope stability and to predict of slope failure.

• International Journal of Highway Engineering
• /
• v.14 no.1
• /
• pp.85-94
• /
• 2012

The term "incident duration time" is defined as the time from the occurrence of incident to the completion of the handling process. Reductions in incident durations minimize damages by traffic accidents. This study aims to develop models to identify factors that influence incident duration by investigating traffic accidents on highways. For this purpose, four models were established including an integrated model (Model 1) incorporating all accident data and detailed models (Model 2, 3 and 4) analyzing accidents by location such as basic section, bridges and tunnels. The result suggested that the location of incident influences incident duration and the time of arrival of accident treatment vehicles is the most sensitive factor. Also, significant implications were identified with regard to vehicle to vehicle accidents and accidents by trucks, in night or in weekends. It is expected that the result of this study can be used as important information to develop future policies to manage traffic accidents.

• Journal of Korean Society for Geospatial Information Science
• /
• v.11 no.2 s.25
• /
• pp.39-45
• /
• 2003

Roads have been developed throughout the history of mankind, and play a significant role among many traffic facilities for the economy, politics and cultures of our lives. However, the management of roads has not been fully scientific or systematic due to governmental policies focused on construction resulting in damages, and the loss of drawings for existing roads. In this case, it is difficult to manage roads using normal cadastre due to its time consuming work. And, when applying satellite surveying to rapidly extract the centerline of roads, it is impossible to obtain data about the status of internal tunnels. Therefore, this study can be used to extract optimum alignment data of tunnels using the data from satellite surveying, and is a practical paper which can contribute to efficient management and usage of alignment data and road facilities in establishing a HMS(Highway Management System) for the renewal and management of the alignment data of roads, by comparing the data from satellites with the alignment data in existing drawings.