• 한국재료학회지
• /
• 제24권1호
• /
• pp.60-65
• /
• 2014

Fe-based amorphous coatings were fabricated on a soda-lime glass substrate by the vacuum kinetic spray method. The effect of the gas flow rate, which determines particle velocity, on the deposition behavior of the particle and microstructure of the resultant films was investigated. The as-fabricated microstructure of the film was studied by field emission scanning electron microscopy (FE-SEM) and high resolution transmission electron microscopy (HR-TEM). Although the activation energy for transformation from the amorphous phase to crystalline phase was lowered by severe plastic deformation and particle fracturing under a high strain rate, the crystalline phases could not be found in the coating layer. Incompletely fractured and small fragments 100~300 nm in size, which are smaller than initial feedstock material, were found on the coating surface and inside of the coating. Also, some pores and voids occurred between particle-particle interfaces. In the case of brittle Fe-based amorphous alloy, particles fail in fragmentation fracture mode through initiation and propagation of the numerous small cracks rather than shear fracture mode under compressive stress. It could be deduced that amorphous alloy underwent particle fracturing in a vacuum kinetic spray process. Also, it is considered that surface energy caused by the formation of new surfaces and friction energy contributed to the bonding of fragments.

• 한국분말재료학회지
• /
• 제29권5호
• /
• pp.382-389
• /
• 2022

A typical trade-off relationship exists between strength and elongation in face-centered cubic metals. Studies have recently been conducted to enhance strength without ductility reduction through surface-treatment-based ultrasonic nanocrystalline surface modification (UNSM), which creates a gradient microstructure in which grains become smaller from the inside to the surface. The transformation-induced plasticity effect in Fe-Mn alloys results in excellent strength and ductility due to their high work-hardening rate. This rate is achieved through strain-induced martensitic transformation when an alloy is plastically deformed. In this study, Fe-6%Mn powders with different sizes were prepared by high-energy ball milling and sintered through spark plasma sintering to produce Fe-6%Mn samples. A gradient microstructure was obtained by stacking the different-sized powders to achieve similar effects as those derived from UNSM. A compressive test was performed to investigate the mechanical properties, including the yielding behavior. The deformed microstructure was observed through electron backscatter diffraction to determine the effects of gradient plastic deformation.

• 대한기계학회논문집B
• /
• 제39권1호
• /
• pp.11-19
• /
• 2015

본 논문에서는 다물질(가연성 기체 혼합물과 금속관) 수치 해석 기법을 활용하여 밀리미터 크기의 얇은 두께의 금속관 내에서의 데토네이션을 모델링하였다. 데토네이션의 해석을 위하여 수소와 에틸렌 혼합물의 실험과 이론적 값을 기반으로 최적화된 1단계 아레니우스 형태의 화학 반응식, 이상기체 상태 방정식을 활용하여 모델링하였다. 또한 금속관의 재료인 구리와 철은 Mie-Gruneisen 상태 방정식과 Johnson-Cook 강성 모델을 활용하여 큰 압력에 의한 관의 소성 변형을 모델링하였다. 다물질 수치 해석을 위한 경계면의 추적 및 경계면 값의 결정은 각각 hybrid particle level-set 기법과 ghost fluid method(GFM)을 통하여 획득하였다. 수치적 해석 결과는 실험값과의 비교를 통하여 검증 하였으며, 관두께(두꺼운 관과 얇은 관)에 따른 내부 유동장의 변화를 확인하였다. 얇은 관의 경우, 데토네이션에 의해 발생하는 높은 내부 압력에 의하여 관의 소성 변형이 일어나고, 이에 따라 발생하는 팽창파에 의해 내부 기체 혼합물의 압력 및 밀도의 감소현상을 확인하였다.

• 열처리공학회지
• /
• 제24권2호
• /
• pp.92-98
• /
• 2011

The influence of the cooling condition after solution treatment on the high temperature fatigue resistance of 23Cr-26Ni heat resistant steel was investigated. Two different cooling conditions were applied to the steel after solution treatment at $1200^{\circ}C$ for 3 hours. One specimen was water quenched immediately after the solution treatment. The other one was furnace cooled at a rate of $0.5^{\circ}C/min$ down to $750^{\circ}C$ after the solution treatment. Then, both specimens were aged at $750^{\circ}C$ for 5 hours. Under two different heat treatment conditions, the low cycle fatigue (LCF) test was performed at $600^{\circ}C$ and room temperature (RT). Only cyclic hardening continued from the beginning until fracture at all strain amplitudes during LCF at $600^{\circ}C$. This phenomenon was attributed to the increase in the dislocation density due to cyclic deformation, which resulted in the interaction between the newly created dislocations and precipitates. Cyclic hardening followed by saturation and cyclic softening was observed at RT. Cyclic softening was attributed to the dislocation annihilation rate exceeding the dislocation generation rate. Other probable factor for cyclic softening was some cavities formed around grain boundaries after 20 cycles. WQ and FC have a similar LCF behavior at RT and $600^{\circ}C$ as shown in the cyclic stress response curves.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.955-958
• /
• 2003

Nepal is a country of mountains The higher order geodetic points were mostly established on the top of mountains and these points were used for the geodetic network extension. Lower order geodetic control networks were established at different times and used for the surveying and mapping activities of the country.. It has been found that the rate of convergence between north and south borders of Nepal to be 21${\pm}$2 mm each year and the rate translation of Kathmandu to 55${\pm}$3 mm/year to the plates. The most intense deformation in Nepal occurs along the belt of high mountains along its northern border res ulting in a strain contraction rate normal to the Himalayan Arc. This belt is approximately 40 km wide and extends into southern Tibet.( 13). Recently Survey Department of Nepal has lunched a program of strengthening the existing geodetic network of Nepal and re-observed the position of higher order geodetic points by using geodetic GPS receivers to evaluate their position and thus to define the precision of the control points once again. This paper describes the observation procedure and the adjustment results of the existing higher order control network of Nepal established in different time using different types of equipment and techniques; and highlights the observation procedure and the result obtained after the post processing of the GPS observation results. Attempt has been made to give the procedure and identify the methodology for the re observation of existing higher order geodetic points by using GPS receiver and post processing the observed data so that the existing higher order geodetic points are within the given accuracy standard.

• 한국재료학회지
• /
• 제13권7호
• /
• pp.429-435
• /
• 2003

In this study the new creep test using miniaturized specimen(10${\times}$10${\times}$0.5 ㎣) was performed to evaluate the creep characteristics for degraded materials of 2.25Cr-1Mo steel. For this creep test, the artificially aged materials for 330 hrs and 1820hrs at $630^{\circ}C$ were used. The test temperatures applied for the creep deformation of miniaturized specimens was X$630^{\circ}C$ and the applied loads were between 45 kg∼80 kg. After creep test, macro- and microscopic observation were conducted by the scanning electron microscope(SEM). The creep curves depended definitely on applied load and microstructure and showed the three stages of creep behavior like uniaxial tensile creep curves. The load exponents of virgin, 330 hrs and 1820 hrs materials based on creep rate showed 14.8, 9.5 and 8.3 at $550^{\circ}C$ respectively, The 1820 hrs material showed the lowest load exponent and this behavior was also observed in the case of load exponent based on creep rupture time. In contrast to virgin material which exhibited fined dimple fractography, a lot of carbides like net structure and voids were observed on the fractography of degraded materials.

• 한국압력기기공학회 논문집
• /
• 제20권1호
• /
• pp.39-48
• /
• 2024

Research reactors are operated under ambient temperature and atmospheric pressure, which is much less severe conditions compared to those in typical nuclear power plants. Due to the high temperature, heat resistant materials such as austenite stainless steel should be used for the reactors in typical nuclear power plants. Whereas, as the effect of temperature is low for research reactors, materials with high resistance to neutron irradiation, such as zircaloy and beryllium, are used. Therefore, these conditions should be considered when performing integrity assessment for research reactors. In this study, a computational technique through finite element (FE) analysis was developed considering the operating conditions and materials of research reactor when conducting integrity assessment. Neutron irradiation analysis techniques using thermal expansion analysis were proposed to consider neutron irradiation growth and swelling in zirconium alloys and beryllium. A user subroutine program that can calculate the strain rate induced by neutron irradiation creep was developed for use in the commercial analysis program Abaqus. To validate the proposed technique and the user subroutine, FE analysis results were compared with hand-calculation results, and showed good agreement. Consequently, developed technique and user subroutine are suitable for evaluating structural integrity of research reactors.

• Journal of Pharmaceutical Investigation
• /
• 제37권3호
• /
• pp.137-148
• /
• 2007

Using a strain-controlled rheometer [Rheometrics Dynamic Analyzer (RDA II)], the steady shear flow properties of a semi-solid ointment base (vaseline) have been measured over a wide range of shear rates at temperature range of $25{\sim}60^{\circ}C$. In this article, the steady shear flow properties (shear stress, steady shear viscosity and yield stress) were reported from the experimentally obtained data and the effects of shear rate as well as temperature on these properties were discussed in detail. In addition, several inelastic-viscoplastic flow models including a yield stress parameter were employed to make a quantitative evaluation of the steady shear flow behavior, and then the applicability of these models was examined by calculating the various material parameters (yield stress, consistency index and flow behavior index). Main findings obtained from this study can be summarized as follows : (1) At temperature range lower than $40^{\circ}C$, vaseline is regarded as a viscoplastic material having a finite magnitude of yield stress and its flow behavior beyond a yield stress shows a shear-thinning (or pseudo-plastic) feature, indicating a decrease in steady shear viscosity as an increase in shear rate. At this temperature range, the flow curve of vaseline has two inflection points and the first inflection point occurring at relatively lower shear rate corresponds to a static yield stress. The static yield stress of vaseline is decreased with increasing temperature and takes place at a lower shear rate, due to a progressive breakdown of three dimensional network structure. (2) At temperature range higher than $45^{\circ}C$, vaseline becomes a viscous liquid with no yield stress and its flow character exhibits a Newtonian behavior, demonstrating a constant steady shear viscosity regardless of an increase in shear rate. With increasing temperature, vaseline begins to show a Newtonian behavior at a lower shear rate range, indicating that the microcrystalline structure is completely destroyed due to a synergic effect of high temperature and shear deformation. (3) Over a whole range of temperatures tested, the Herschel-Bulkley, Mizrahi-Berk, and Heinz-Casson models are all applicable and have an almostly equivalent ability to quantitatively describe the steady shear flow behavior of vaseline, whereas the Bingham, Casson,and Vocadlo models do not give a good ability.

• Nuclear Engineering and Technology
• /
• 제21권2호
• /
• pp.111-122
• /
• 1989

고온 수증기(1323 K)분위기에서 산화시킨 지르칼로이-4 피복관으로, 구리 맨드렐 팽창실험(Copper Mandrel Expension Test)을 변형률(Strain Rate)이 $3.0\times10^{-5}$/sec일때 673-1173 K 온도 범위에서 수행하였다. 본 연구에서, 산화매개변수(Ki)는 시간(t)의 제곱근에 비례하고 $(Ki=\delta_{kit}\frac{1}{2}$), 비례상수($\delta_{ki}$)는 무게증가(Weight Gain), Zr02의 두께, $\alpha$(0) 층에 대하여 각각 0.281, 2.82, 2.313을 사용하였다. 지르칼로이-4의 고온(873-1073 K) 소성변형에 의한 활성화 에너지는 Zr02가 높은 강도를 갖기 때문에 산화 시간이 5분에서 60분으로 증가함에 따라 251 KJ/mol에서 323KJ/mo1로 증가하였다. 산화막 두께, K와 항복 응력의 관계는 ($\sigma/C)^n=K^m$exp (Q/RT)인 관계식을 얻었다. 여기서 n은 6.9, m은 5.7, 그리고 Q가 251, 258, 316, 323 KJ/mo1에 대해 C는 0.155, 0.138, 0.051, 0.046MPa이다.

• Geomechanics and Engineering
• /
• 제21권5호
• /
• pp.433-445
• /
• 2020

The weakening and softening behavior of soft clay subjected to cyclic loading due to the build-up of excess pore water pressure is well-known. During the design stage of the foundation of highways and coastal high-rise buildings, it is important to study the mechanical behavior of marine soils under cyclic loading as they undergo greater settlement during cyclic loading than under static loading. Therefore, this research evaluates the cyclic stress-strain and shear strength of untreated and treated marine clay under the effects of wind, earthquake, and traffic loadings. A series of laboratory stress-controlled cyclic triaxial tests have been conducted on both untreated and treated marine clay using different effective confining pressures and a frequency of 0.5 and 1.0 Hz. In addition, treated samples were cured for 28 and 90 days and tested under a frequency of 2.0 Hz. The results revealed significant differences in the performance of treated marine clay samples than that of untreated samples under cyclic loading. The treated marine clay samples were able to stand up to 2000 loading cycles before failure, while untreated marine clay samples could not stand few loading cycles. The untreated marine clay displayed a higher permanent axial strain rate under cyclic loading than the treated clay due to the existence of new cementing compounds after the treatment with recycled tiles and low amount (2%) of cement. The effect of the effective confining pressure was found to be significant on untreated marine clay while its effect was not crucial for the treated samples cured for 90 days. Treated samples cured for 90 days performed better under cyclic loading than the ones cured for 28 days and this is due to the higher amount of cementitious compounds formed with time. The highest deformation was found at 0.5 Hz, which cannot be considered as a critical frequency since smaller frequencies were not used. Therefore, it is recommended to consider testing the treated marine clay using smaller frequencies than 0.5 Hz.