• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.3
• /
• pp.229-236
• /
• 2013

This paper presents the experimental investigation of a biplane micro air vehicle. The effects of geometric parameters, gap, stagger, and decalage angle are investigated at low Reynolds number (~150,000) in a low-speed wind tunnel. A rigid flat plate with an aspect ratio of one and square planform shape is used to evaluate all three geometric parameters. The side dimension of the single flat plate is 0.15 m. The goal is to find an optimal biplane configuration that should exceed monoplane performance by generating high lift and flying as slow as possible, in order to capture high-quality visual recordings. This configuration will directly help to fly at a lower velocity and to make tighter turns that are advantageous in restricted environments. The results show that the aerodynamic performance of the biplane MAV is significantly enhanced through the combination of gap and stagger effects. A performance comparison demonstrates the superiority of the optimal biplane configuration compared to a monoplane in cruise and glide phases. Moreover, no significant compromise is found for the range, endurance, and climb performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.6
• /
• pp.954-959
• /
• 2015

In this paper, 110kW high output density, high efficiency Permanent Magnet Synchronous Motor which can be applied on tram’s traction system is introduced, along with its output and loss characteristics. The motor model is 2pole 18slot model and its size has been reduced through the high speed for high output density. Especially, structure and retainer sleeve structure is applied to its structure, which is also appropriate for high speed rotation. This kind of structure has eddy current loss problem on the surface of rotor, which must be reduced for high output density design. This study has designed the most optimized additional design parameter in order to improve the output characteristics and efficiency of previous produced 2pole 18 slot 110kW motor model and how the width of airgap affects from the loss perspective is mainly analyzed. Finally, the analysis on the extent of the efficiency improvement effect compared to the previous model has performed through electromagnetic FEM analysis. The influence of airgap flux density distribution has also been thoroughly examined.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.170-177
• /
• 2020

This study examined the clamping force control method and the braking performance test results of an electromechanical brake (EMB) using braking test equipment. Most of the studies related to EMBs have been carried out in the automotive field, dealing mainly with the static test results for various control methods. On the other hand, this study performed a dynamic performance evaluation. The three-phase interior permanent magnet synchronous motor (IPMSM) was applied to drive the actuator of the EMB, and the analysis was verified by JMAG(Ver. 18.0), which is finite element method (FEM) software. The current control, speed control, and position control were used for clamping force control of the EMB, and the maximum torque per ampere (MTPA) control was applied to the current controller for efficient control. The EMB's emergency braking deceleration performance was tested in the same way as conventional pneumatic brake systems when the wheel of a train rotates at 110 km/h, 230 km/h, and 300 km/h. The emergency braking time, with the wheel stopped completely at the maximum rotational speed, was approximately 73 seconds. The similarity of the braking time and deceleration pattern was verified through a comparison with the performance test results of the pneumatic brake system applied to the next generation high-speed railway vehicle (HEMU-430X).

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.663-669
• /
• 2011

Since railway vehicle's improvements on speed and weight has caused interior noise, the passenger's convenience fell dramatically. Therefore many on-going researches are dedicated to reduce interior noise. In this study the analytical prediction of interior noise reduction has done through filling up the empty space using form and to modify the floor structure, which contributes highly with interior noises. Using Statistical Energy Analysis(SEA), the interior noise of the vehicles without the form filling on the floor structure and the vehicles with form filling and also a modified structure has been predicted. The selected percentage of form filling was 0, 50, 100% and through this research the analysis of noise reduction by form filling has been made. When floor structure has been filled with form, approximately 2 dB of noise reduction was observed and the difference of noise reduction level with 50 and 100% form filling was predicted to be very little. Through this study, the expectation of interior noise reduction in high speed trains is considered high.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.303-310
• /
• 2011

This paper is focused on development of models for measuring lateral and vertical track irregularities from corresponding accelerometers of an in-service high-speed train. Generally, the track irregularity was measured by a special railway inspection vehicle or system with contact or non-contact sensors. However, the sensors are very expensive and vulnerable to a harsh environment. Displacement estimation from an inertial measurement unit and its wave-band filtering was already developed in the previous study, and it was found that their results included not only the track irregularities but also other information such as phase delay of the applied filters, and suspension and conicity of the wheel. To identify the track irregularities from those results, a compensation filtering method was proposed. Each directional compensation filter was derived by using a system identification method with the estimated directional displacement as input and the corresponding track irregularities as output. In this paper, they are integrated into a model for each direction and applied to the measured lateral and vertical acceleration data from the axle-box and bogie of an in-service high-speed train. Their results are compared with the data from the track geometry measurement system. From the comparison, the proposed models are a useful tool for the measurement of the track irregularities using accelerometers of in-service high-speed trains.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.1
• /
• pp.22-29
• /
• 1999

In the development of high speed marine vehicle, lilting devices became important in sharing the pay load or controlling the attitude. The devices are also important to meet the IMO regulation to prevent the marine pollution by keeping the high rudder force for VLCC even in low speed operation. The high lift devices such as the Coanda device have been introduced to the aircraft as a common practice for a long time among the aero-engineers. If the Coanda device can be utilized to the flapped rudder, the severe requirement of rudder force could be provided for the VLCC in low speed operation. The performance of the rudder system has been investigated at the towing tank of Seoul National University.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3181-3183
• /
• 1999

A CMOS two-stage oscillator applicable to requiring in- and quadrature-phase components such as RF and data retiming applications are presented using phase-look-ahead technique. This paper clearly describes the operation principle of the presented two-stage oscillator and the principle can be also applicable to the high speed high speed divide-by-two is usually used for prescaler of the frequency synthesizer. Also, the sucessful oscillation of the proposed oscillator using PLA is confirmed through the experiment. The test vehicle is designed using 0.8 ${\mu}m$ N-well CMOS process and it has a maximum 914MHz oscillation showing -75dBclHz phase noise at 100kHz offset with single 2V supply.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.56 no.2
• /
• pp.74-82
• /
• 2007

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications, due to their excellent power to weight ratio. This paper proposes efficiency optimization control of IPMSM drive using adaptive fuzzy learning control fuzzy neural network (AFLC-FNN) controller. In order to maximize the efficiency in such applications, this paper proposes the optimal control method of the armature current. The controllable electrical loss which consists of the copper loss and the iron loss can be minimized by the optimal control of the armature current. The minimization of loss is possible to realize efficiency optimization control for the proposed IPMSM. The optimal current can be decided according to the operating speed and the load conditions. This paper considers the design and implementation of novel technique of high performance speed control for IPMSM using AFLC-FNN controller. Also, this paper proposes speed control of IPMSM using AFLC-FNN and estimation of speed using ANN controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The proposed control algorithm is applied to IPMSM drive system controlled AFLC-FNN controller, the operating characteristics controlled by efficiency optimization control are examined in detail.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.2
• /
• pp.89-97
• /
• 2006

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications, due to their excellent power to weight ratio. The paper is proposed maximum torque control of IPMSM drive using learning mechanism-fuzzy neural network(LM-FNN) controller and artificial neural network(ANN). The control method is applicable over the entire speed range and considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal d-axis current $i_{d}$ for maximum torque operation is derived. This paper considers the design and implementation of novel technique of high performance speed control for IPMSM using LM-FNN controller and ANN controller. The hybrid combination of neural network and fuzzy control will produce a powerful representation flexibility and numerical processing capability. Also, this paper is proposed speed control of IPMSM using LM-FNN and estimation of speed using ANN controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The proposed control algorithm is applied to IPMSM drive system controlled LM-FNN and ANN controller, the operating characteristics controlled by maximum torque control are examined in detail. Also, this paper is proposed the analysis results to verify the effectiveness of the LM-FNN and ANN controller.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.4
• /
• pp.239-247
• /
• 2015

Recently, various research studies on frontal collision and rear-ender which occur more frequently compared to others are underway as the public interest on them is growing. This study analyzes scientifically the relationship between effective impact speed and injury incidence for vehicle crash accident reconstruction and presents a relevant model formula. Because real vehicle experiments have certain limitations such as possible injuries, this study efforts to collect and analyze as many materials as possible to substitute real vehicle experiments, including data from various collision tests and human experiments. As a result, this study present a threshold in which head-on collisions and rear impacts do not cause injuries under 7 km/h of effective impact speed, and suggests a model formula showing that injury extent is linearly proportional to effective impact speed through collision speed and amount of plastic deformation. In conclusion, a model formula for estimating effective impact speed and injury incidence newly proposed in this study is expected to be used as a minimum standard of judgment in disputes on the injury extent of passenger in head-on collisions and rear impacts. Furthermore its availability in terms of technological analysis in legal arguments is expected to be very high if this study will be enhanced by referring to scientific analyses of various real accidents so as to apply it in various types of collision accidents.