• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.177-180
• /
• 2004

The development of a tilting train with construction of electric line on the conventional railway is required for speed-up on the conventional railway with many curving sections. For development of tilting train, the study and development of the tilting system and tilting bogie having the different mechanism with a general high speed train will play a main role for improving the technology in the field of Korean railway The study and development of the pantograph tilting mechanism in order to keep a good contact behavior between a pantograph and a contact wire by tilting a pantograph on the opposite direction of the vehicle tilting direction. In this study, we analyzed the aerodynamic characteristic of a developing pantograph on the tilting train and obtained the contact force with catenary by aerodynamic lift force by the aerodynamic analysis. We also performed the numerical analysis for design the device controlling lift force on a pantograph. From the aerodynamic simulation and parameter study for a device to control the lift force, we will suggest the various shape and the optimal shape of it corresponding to a developing tilting pantograph. The Fluent software is used for the calculation of flow profile in this study.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.65-72
• /
• 2012

Numerical simulations were performed to study the stall characteristics of turboprop aircraft. Stall characteristics were qualitatively investigated using the computational results of various configurations based on the combinations of propeller and high lift device. For the analysis of stall characteristics, three-dimensional Navier-Stokes solver with Spalart-Allmaras turbulence model was used and the relative motion between propeller and wing was simulated using sliding mesh technique. For the cruise configurations, major flow separation was occurred at the fuselage/wing fairing and the separation was reduced under propeller slipstream condition. For the high lift device configuration without propeller, major flow separation was occurred at the outboard side of nacelle. With rotating propeller, early stall onset due to low relative velocity and high effective angle of attack was observed on the outboard wing section. Regarding rotating direction of propeller, inboard-down direction was preferred due to the stall delay effect of propeller slipstream.

• Proceeding of EDISON Challenge
• /
• 2012.04a
• /
• pp.13-16
• /
• 2012

본 논문에서는 항공기의 제어 안정성(Control Stability)과 조종성(Controllability), 그리고 기계 하중을 줄여 구조와 공기역학적인 안정성을 향상시키기 위해 고양력장치(High-lift Device)인 플랩에 탭이 추가된 익형을 설계하였다. 이 과정에서 한정된 해석자원 때문에 많은 설계조건을 해석하는데 어려움이 있었다. 이를 해결 하기위해 얇은 익형 해석(Thin Airfoil Theory)을 이용하여 지정된 설계구속조건을 통해 시위선을 지정하고 이를 바탕으로 두께를 부여하여 최종적인 익형을 설계하였다. EDISON CFD 2.0 Solver를 이용해 최종 설계한 익형의 성능을 해석하였다. 이를 바탕으로 플랩만 존재하는 익형에 비해 양력손실률이 15%이하로 감소하고, 힌지 모멘트가 최소인 공기역학적 익형을 산출하였다.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.242-249
• /
• 2009

High-rise construction sites, especially those situated in spatially constrained urban areas, have difficulties in timely delivery of materials. Modern techniques such as Just-in-time delivery, and use of information technology such as Project Management Information System (PMIS), are targeted to improve the efficiency of the logistics. Such IT-driven management techniques can be further benefited from state-of-the-art devices such as Radio Frequency Identification (RFID) tags and Ubiquitous Sensor Networks (USN), which has resulted in notable achievements in automated logistics management at the construction sites. Based on those achievements, this research develops USN hardware toolkits for construction lifts, which aims to be automated the vertical material delivery by sensing the material information and routing it automatically to the right place. The gathered information from the sensors can also be used for monitoring the overall status. The developed system will be tested in the actual high-rise construction sites to assess the system's feasibility. The proposed system is being implemented using Zigbee communication modules and RFID sensor networks which will communicate with the intelligent palette system (previously developed by the authors). To support the system, a lift-mountable intelligent toolkit is under development. Its feasibility test will be conducted by applying the implemented system to a test bed and then analyzing efficiency of the system and the toolkit. The collected test data will be provided as a basis of autonomous vertical transport equipment development. From this research, efficient management of the material lift is expected with increased accuracy, as well as better management of overall construction schedule benefited from the system. Further research will be expected to develop a smart construction lift, which will eliminate the need for human supervision, thus enabling a real 'autonomous' operation of the system.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.6
• /
• pp.711-719
• /
• 2019

At present, wind power is the fastest growing technology in the world. The domestic market depends heavily on imports for wind tower lift. so it manage through the overseas maker. The lift manufacture, establishment and maintenance utility is increasing, localization development of one wind tower lift is necessary with domestic fundamental base technique. In this paper, we will study the components necessary for the development of onshore offshore wind tower elevators, which are currently dependent on total imports, in line with the high growth of the wind market and the enlargement of the wind power generators. First of all, endless winders and cabins, which are the core components of the offshore wind tower lift, were examined for the components that affect the structural safety. Structural analysis was performed on Sheave, which is responsible for most of the lift lifting loads, and Block Stop, a safety device that prevents the cabin from falling in an emergency. The structural suitability was evaluated by comparing with the safety factor. In addition, the on-board control panel combines the control panel of the elevator and the drive motor driving the endless winder for efficient control of the offshore wind tower lift. The addition of features improves ride comfort at departure.

• Journal of computational fluids engineering
• /
• v.21 no.4
• /
• pp.85-89
• /
• 2016

Wing is the most important part of aircraft which produces lift. In general when aircraft takes off or lands, high lift is required and additional devices are adopted in front and aft-side of wing, which constitute so-called multi element airfoils. The objective of this research is to develop a specialized grid generation program to help engineers in reducing human labor and eliminating time-consuming process for mesh regeneration by deforming the initially-given grid system with efficient deforming method. This paper describes briefly about the mesh deformation methods, and provides some results to verify the quality of deformed mesh and eventually correctness of current approach.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.6 s.237
• /
• pp.755-762
• /
• 2005

To evaluate the aerodynamic efficiency of TR-S2 configuration designed by SUDC, wind tunnel tests of $40\%$ scaled model were done in KARI LSWT. The aerodynamic characteristics of plain and Semi-Slotted Flaperon were compared, and vortex generators were installed to improve flow pattern along the wing surface. Effects of the control surface such as elevator, rudder, aileron, and incidence angle of horizontal tail are measured for various testing conditions. Test results showed that Semi-Slotted Flaperon produced more favorable lift, lift/drag, and stall margins and application of vortex generator would be best choice to enhance wing performance. Longitudinal, lateral and directional characteristics of TR-S2 were found to be stable for the pitch and yaw motions.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.101-104
• /
• 2004

CFD simulation is peformed for 2D and 3D frisbees flying at 10m/s. For convenience of simulation, rotation of 3D model is not considered. CFD results show that pitching moment makes the nose down and holes at the leading and trailing edges improve the lift characteristics of the frisbee.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.78-83
• /
• 2010

Since a tower crane is too high for a worker to ascend and by the wind in the high altitude, the possibility of a safety accident is very high, a lift assist is used. In this study, the hydraulic fall prevention device using the pressure generation device by Seok, et al. was developed. For this, the effects on the fall prevention performances of factors such as gear clearance, oil viscosity, rotative velocity and so on were evaluated by the analysis of fluid flow using FEM and the prototype was producted and a function test was performed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.260-261
• /
• 2017

The objective of this study is to propose the basic design plan of system by comparing and analyzing application environment of lift and elevator group control system, as preliminary study for the application of group control system to lifts for high-rise construction. The basic design plan is suggested in terms of group control algorithm, hall call system type, operation information recording device, information communication method, and operation method. The results of this study can be used as basic data for software and hardware design for application of group control technology of lifts for super tall building construction and ultimately contribute to improve the operation efficiency of lift for high-rise construction.