• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.4
• /
• pp.165-174
• /
• 2004

This study is about a horizontal load test of buoyance anchor installed in the section where underground water level happens in the depth of 5m under the ground when the ground is excavated, because the section as a excavation section of high speed railway ${\bigcirc}{\bigcirc}$ station is near a rivers and because the section always has a reservoir of full water level on the left. Therefore, in this study we will appraise the long-term stability of the structure permanently being taken buoyance by the underground water level, through the spot test of the buoyance anchor installed in the section where underground water level happens. For that, Bar Type anchor is used, which can get enough pulling-out force by a method to resist buoyance by using friction force against the ground by high strength steel rod or steel wire. Anti-buoyance anchor is installed on the bottom slab of underground structure being taken horizontal force by the braking and accelerating of high speed train. And, It is aimed to analyze and grasp the review result of stability for the horizontal force that happens at the parking and stopping of high speed train, by executing horizontal load test for the grasping of the movements characteristic of buoyance anchor.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.4
• /
• pp.457-471
• /
• 2015

A domestic cutterhead with the diameter of 3.6 m was designed and manufactured in this study. Then, it was attached to an existing earth-pressure balanced shield TBM to excavate a cable tunnel with the length of 1,275 m. Especially, the procedures for TBM cutterhead design and its corresponding performance prediction were also summarized. From field data analyses of the refurbished shield TBM, its maximum advance rate was recorded as 14.4 m/day. Penetration depths of disc cutters were found to be approximately 4 mm/rev, which is equal to the maximum penetration depth designed for the strongest rock strength condition in the target tunnel. Every TBM operating thrust and cutter normal force during TBM driving was much smaller than their corresponding maximum capacities. When cutter acting forces recorded in the field were analyzed, their prediction errors by the CSM model were very high for weak rock conditions. In addition, rock strength showed very close relationships with cutter normal force and penetration depth.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.777-785
• /
• 2021

Many utility lines are buried underground to provide various functions of the city. Because historical records are not managed systematically, damage has occurred during excavation. In addition, the demand for an underground facility management system is increasing as the aerial underground project is progressing. By attaching an electronic recognition sensor to an underground facility, such as pipelines, the management history and site conditions can be carefully managed. Therefore, in this study, electronic recognition sensors, such as BLE Beacon, UHF RFID, geomagnetic sensor, and commercial marker, were tested to analyze the strengths, weaknesses, and field applicability through a pilot project. According to the limited research results collected through two pilot projects, the installation depth is most important to demonstrate the performance of the electronic reader. In addition, because it should be used in urban areas, the influence of environmental interference should be minimized, and there should be no performance degradation over time. In the case of the geomagnetic recognizer, the effect of environmental interference was large, and performance degradation occurred over time using the BLE Beacon. In the field situation, where the installation depth can be controlled to less than 40cm, the utility of the battery-free UHF RFID was the best.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.3
• /
• pp.261-275
• /
• 2020

When excavating a small cross-section tunnel in a fault fracture zone using the shield TBM method, there is a high possibility of excessive convergence and collapse. Appropriate ground reinforcement is required to minimize construction cost loss and trouble due to a fault fracture zone. In this study, the optimal reinforcement area was suggested and the surrounding ground behavior was investigated through numerical analysis using MIDAS GTS NX (Ver. 280). For the parameters, the width of the fault fracture zone, the existence of fault gouge, and the groundwater level and depth of cover were applied. As a result, when there is not fault gouge, the convergence and ground settlement are satisfied the standard when applying ground reinforcement by up to 0.5D. And, due to the high permeability coefficient, it is judged that it is necessary to apply 0.5D reinforcement. There is a fault gouge, it was possible to secure stability when applying ground reinforcement between the entire fault fracture zone from the top of the tunnel to 0.5D. And, because the groundwater discharge occurred within the standard value due to the fault gouge, reinforcement was unnecessary.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1161-1167
• /
• 2016

In this study, an attempt was made to conduct a case study on the development of ground expansive displacement due to lack of bearing capacity of original ground in spite of applying reinforcement treatments that intended to enhance the stability of big size high-speed rail tunnel in large fault zone. For the purpose of this, in-situ measurements made in the middle of excavation stage were analyzed in order to characterize ground responses and numerical analysis was performed to evaluate the effectiveness of reinforcement technique such as elephant foot method applied for this site via comparing with field monitoring measurements. In addition, further numerical studies were carried out to investigate the influence of leg pile installation angle and length, which is one of types of elephant foot method. The results revealed that the optimum condition for the leg pile installation is to maintain 45 degree of installation angle along with 6 meter of embedment depth.

• 대한공업교육학회지
• /
• v.41 no.1
• /
• pp.68-87
• /
• 2016

This research conducted a survey for total 166 teachers of schools so as to analyze validity and satisfaction for performance objectives of SMB administration subsidy the HRDP and the CEP in Specialized High School. The results of research are as follows. First, teachers recognize that purpose of HRDP is to expand employment of specialized high school and provide human resource of SMB. And, they recognize that HRDP is important to improve school outcomes and makes a positive effect on the improvement of school outcomes. Second, teachers recognize that objectives of HRDP are improvement of student's understanding for SMB, improvement of teacher's understanding for SMB, improvement of SMB's understanding of school, cultivation of student's occupational view, systematization of career guiding program based on employment process, strengthening of industry-academia cooperation education, improvement of the level of student's skill, fulfillment of workplace experience and practice focusing workplace learning, training of customized human resource for SMB, improvement of student's adaptation to the workplace, improvement of employment rate for SMB, expansion of job opportunities for students with SMB, preparation of the base of connection between school and SMB, publicity of school, expansion of opportunities to cooperate between SMB and school, establishment of cooperative system among industrial association and school, introduction and operation of the employment connective model for joint education and employment, strengthening of field professionalism of teachers. However, satisfaction for the achievement of objectives of HRDP except for strengthening of industry-academia cooperation education and improvement of employment rate for SMB is relatively lower than the validity. Third, teachers in charge of human resource training business of middle and small sized company's specialized high school recognize that objectives of CEP are expansion of job opportunities for students with SMB, excavation of good-quality SMB, expansion of opportunities to cooperate between SMB and school, fulfillment of workplace learning, improvement of student's major foundation and in-depth skill, improvement of literacy, math, teamwork and communication abilities for students' job performance, improvement of student's working attitude and student's proper career exploration decision. However, satisfaction for achievement of objectives of CEP is relatively lower than the validity.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.2
• /
• pp.27-40
• /
• 2021

This study was carried out for the description of the conflicts on the measurement of the root collar diameter of the landscape trees that are currently being produced, distributed, and planted in S. Korea, and for determination of the standard for root collar diameter measurement. The difference in consciousness of appropriate measurement of root collar diameter among different ages of landscape practitioners was statistically significant at p<0.05 level. It seemed to be due to the difference in the amount of field experiences among different age groups. On "the ambiguity of measuring the root collar diameter' of landscape trees", the consciousness was significantly different at p<0.05 level among job positions. On "Improvement of measurement criteria for landscape trees," it was significantly different at p<0.05 level among job types. This was thought to be due to the disagreement between the client and the contractor. On "prevention of topsoil removal" when excavating landscape trees, the consciousness was significantly different at p<0.001 level among different age groups, and different at p<0.01 level among different occupations, and different at p<0.05 level among different working area. The consciousness on "removing top soil when excavating landscape trees and rooting after transplantation" was not significantly different. The consciousness on the conflict caused by "ambiguity in root collar diameter measurement criteria" was high with an average of 3.85 for job type, occupation, jop position, and work experience. It was higher for landscape contractors than public institutions. The higher job positions and more experiences, the more conflicts. The consciousness on the appropriate position of root collar diameter measurement for landscape trees revealed that measuring at above-ground part (66.5%) was prefered to the underground part (33.0%). During the excavation of landscape trees for transplant, topsoil removal up to average depth of -2cm to -4cm was favored by 84.0%, and the purpose of removing topsoil was recognized as 'to increase the size and unit cost' by 59.7%.