• 한국농공학회지
• /
• 제35권2호
• /
• pp.43-56
• /
• 1993

The laboratory tests are performed on how the liquefaction potential of the sea dike structures on the saturated sand or silty sand seabed could be affected due to earthquake before and after construction results are given as follows ; 1. Earthquake damages to sea dike structures consist of lateral deformation, settlement, minor abnormality of the structures and differential settlement of embankments, etc. It is known that severe disasters due to this type of damages are not much documented. Because of its high relative cost of the preventive measures against this type of damages, the designing engineer has much freedom for the play of judgement and ingenuity in the selection of the construction methods, that is, by comparing the cost of the preventive design cost at a design stage to reconstruction cost after minor failure. 2. The factors controlling the liquefaction potential of the hydraulic fill structure are magnitude of earthquake(max. surface velocity), N-value(relative density), gradation, consistency(plastic limit), classification of soil(G & vs), ground water level, compaction method, volumetric shear stress and strain, effective confining stress, and primary consolidation. 3. The probability of liquefaction can be evaluated by the simple method based on SPT and CPT test results or the precise method based on laboratory test results. For sandy or silty sand seabed of the concerned area of this study, it is said that evaluation of liquefaction potential can be done by the one-dimensional analysis using some geotechnical parameters of soil such as Ip, Υt' gradation, N-value, OCR and classification of soils. 4. Based on above mentioned analysis, safety factor of liquefaction potential on the sea bed at the given site is Fs =0.84 when M = 5.23 or amax= 0.12g. With sea dike structures H = 42.5m and 35.5m on the same site Fs= 3.M~2.08 and Fs = 1.74~1.31 are obtained, respectively. local liquefaction can be expected at the toe of the sea dike constructed with hydraulic fill because of lack of constrained effective stress of the area.

• 방사성폐기물학회지
• /
• 제8권3호
• /
• pp.207-213
• /
• 2010

국산 칼슘 벤토나이트를 대상으로 온도가 팽윤압에 미치는 영향을 관찰하였다. 벤토나이트를 건조밀도 1.6 g/$cm^3$으로 압축하고, 0.69 MPa의 일정한 수압으로 증류수를 공급하여 팽윤압을 측정하였다. 온도 영향 실험은 $25^{\circ}C$, $30^{\circ}C$, $40^{\circ}C$, $50^{\circ}C$, $60^{\circ}C$, $70^{\circ}C$, respectively. The Ca-bentonite showed a sufficiently high swelling pressure of 5.3 MPa에서 승온조건과 감온조건으로 수행하였다. 압축 벤토나이트가 물과 접촉하여 상온에서 5.3 MPa의 충분히 높은 팽윤압이 작용하는 것을 실험적으로 확인하였다. 팽윤압은 온도가 높을수록 감소하는 것으로 나타났다. 승온조건과 감온조건에서의 온도에 따른 팽윤압 거동에 차이를 보이며, 승온조건에서 온도에 따른 변화가 심하게 나타났다. 향후 온도 조건 외에 벤토나이트의 압축밀도 변화, 지하수 조성에 따라 팽윤압 특성이 어떻게 변화하는지에 대해 평가한다면, 앞으로 국내 고준위 폐기물 처분장의 개념 설계에 유용하게 활용될 수 있을 것으로 본다.

• 지질공학
• /
• 제20권3호
• /
• pp.297-310
• /
• 2010

본 연구는 태안화력본부 회사장에 비회와 저회가 혼합되어 매립된 혼합회를 건설재료로 활용하기 위한 기초연구로서 대상 혼합회의 물리적 시험 및 역학적 시험을 실시하여 도로성토용 재료 및 구조물 뒤채움용 재료로 활용가능한지 판단하고자 공학적 특성을 검토하였다. 비중, 최대 최소밀도, 액 소성, 입도분석, XRD, 강열감량시험을 통해 물리 화학적 특성을 평가하였고 투수, 다짐, CBR, 삼축압축시험을 실시하여 역학적 특성을 평가하였다. 혼합회의 실험결과 비중은 2.18~2.20, 건조밀도는 $9.38{\sim}13.32\;kN/m^3$, 수정 CBR은 16.5~21%, 투수계수는 $1.32{\times}10^{-4}{\sim}1.89{\times}10^{-4}cm/sec$, 배수마찰각은 $36.43{\sim}41.39^{\circ}$로 나타났다. 물리 역학적 실험결과를 토대로 도로성토용 재료와 구조물 뒤채움용 재료로써의 품질기준과 비교해 본 결과 활용이 가능할 것으로 판단되었다. 그러나 비회의 함유율이 높은 혼합회는 일부 품질기준을 만족하지 못하므로 도로성토용 재료와 구조물 뒤채움용 재료로 활용하기 위해서는 저회와의 배합을 통한 품질개선이 필요할 것으로 판단되었다.

• 한국농공학회지
• /
• 제20권1호
• /
• pp.4575-4591
• /
• 1978

In order to investigate the effects of grain size distribution, cement content, and molding pressure on the strength and durability of soil-cement mixtures, a laboratory test of soil cement mixtures was performed at four levels of cement content, five levels of molding pressure, and four levels of normal curing periods. The results are summarized as follows: 1. Optimum moisture contents in loam soil and maximum dry density in sand soil increased with the increase of cement content, but in others, both optimum moisture contents and maximum dry density were changed ununiformly. 2. When the specimens were molded with molding pressure, 50kg/$\textrm{cm}^2$, strength of soil cement mixture with cement content, 2 and 4 per cent, was lower than the strength of soil cement mixture without cement content by more than 40 to 50 per cent. 3. The strength of soil-cement molded with molding pressure, 100kg/$\textrm{cm}^2$, was higher than the strength of soil-cement molded with M.D.D. obtained from standard compaction test more than 40 per cent in sand loam cement and 50 per cent in loamy cement. 4. There was highly significant positive correlation among molding pressure, cement content and unconfined compressive strentgh and so the following multiple regression equations were obtained. Loam: fc=1.9693C+0.197P-0.84 Sandy loam: fc=2.9065C+0.235P-0.77 5. When the specimens were molded with molding pressure, 20 to 100kg/$\textrm{cm}^2$, the regression equation between the 28-day and 7-day strenght was obtained as follows. Loam : q28=1.1050q7+7.59(r=0.9147) Sandy loam : q28=1.3905q7+3.17 (r=0.9801) 6. At the cement contents of above 50 per cent, the weight losses by freeeze-thaw test were negligible. At the cement content of below 8 per cent the weight losses were singnificantly high under low molding pressure and remarkably decreased with the increase of molding pressure up to 80kg/$\textrm{cm}^2$. 7. Resistance to damage from water and to absorption of water were not improved by molding pressure alone, but when the soil was mixtured with cement above 6 per cent, damage seldoms occurred and absorbed less than 5 per cent of water. 8. There was highly significant inverse-corelationship between the compressive strength of soil cement mixtures and their freeze-thaw loss as well as water absorption. By the regression equation methods, the relationships between them were expessed as followed fc=-7.3206Wa+115.6(r=0.9871) log fc=-0.0174L+1.59(r=0.7709) where fc=unconfined compressive stregth after 28-days curing. kg/$\textrm{cm}^2$ Wa=water absorption, % L : freeze-thaw loss rate, %

• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.49-58
• /
• 2015

PURPOSES : The use of environmentally friendly construction methods has been recently encouraged to reduce fuel consumption and the effects of global warming. For this purpose, the roller compacted concrete pavement (RCCP) construction method has been developed. RCCP is more environmentally friendly and economically efficient than general concrete by reducing the amount of CO2 generated through the application of a smaller amount of cement. RCCP has a number of advantages such as an easy construction method, low cost, high structural hydration performance, and aggregate interlocking. However, mix design standards and construction guidelines of RCCP are required for domestic application. In addition, a study on aggregate selection, which has an effect on the characteristics of RCCP, is necessary owing to a limited number of researches. Thus, the aggregate effect on the performance of RCCP in securing the required strength and workability was evaluated in consideration of domestic construction. METHODS : Sand and coarse aggregates of both 19mm and 13mm in maximum size were used in this study. Four types of aggregate gradations (s/a = 30%, 58%, and 70% for the sand and coarse aggregate of 19mm in maximum size, and s/a = 50% for a combination of the three types of aggregates) were set up to investigate the effects of the PCA band on the RCC characteristics. The conditions of s/a = 30% and 70% were evaluated to check the gradation effect outside of the recommended band. The conditions of s/a = 58% and 50% were used because they are the optimum combination of the two and three types of aggregates, respectively. RCCP gradation band was suggested gradation with a proper construction method of RCCP by synthetically comparing and analyzing the correlation of optimum water content, maximum dry density, and strength of requirements through its consistency and compaction test. RESULTS : The lower and upper limit lines are insufficient to secure a relatively strong development and workability compared to an aggregate gradation in the RCCP gradation band region. On the other hand, the line in the RCCP gradation band and the 0.45 power curve in the RCCP gradation band region were satisfactory, ensuring the required strength and workability. CONCLUSIONS : The suitable aggregate gradation on RCCP process should meet the RCCP gradation band area; however, fine particles passing through a #60 sieve do not need to be within the recommended gradation band because the influence of this region on such fine particles is small.

• 한국농공학회지
• /
• 제37권3_4호
• /
• pp.61-71
• /
• 1995

Natural ground is a composite consisted of the three phases of water, air and soil paircies. Among the three components, water as a material is weU understood but soil particles are not in foundation engineering. Especially, weathered granite soil generally shows a large volumetric expansion when they freeze. And, the stability and durability of the soil have shown decreased with repetitive freezing and thawing processes. These unique charcteristics may cause various construction and management problems if the soil is used as a construction material and foundation layers. This project was initiated to investigate the soil's physical and engineering characteristics resulting from freezing and freezing-thawing processes. Research results may be used as a basic data in solving various problems related to the soil's unique characteristics. The following conclusions were obtained: The degree of decomposition of weathered granite soil in Kangwon-do was very different between the West and East sides of the divide of the Dae-Kwan Ryung. Soil particles distributed wide from very coarse to fine particles. Consistency could be predicted with a function of P200 as LL=0.8 P200+20. Permeability ranged from 10-2 to 10-4cm/sec, moisture content from 15 to 20% and maximum dry density from 1.55 to 1.73 g /cmΥ$^3$ By compaction, soil particles easily crushed, D50 of soil particles decreased and specific surface significantly increased. Shear characteristics varied wide depending on the disturbance of soil. Strain characteristics influenced the soil's dynamic behviour. Elastic failure mode was observed if strain was less than 1O-4/s and plastic failure mode was observed if strain was more than 10-2/s. The elastic wave velocity in the soil rapidly increased if dry density became larger than 1.5 g /cm$^3$ and these values were Vp=250, Vg= 150, respectively. Frost heave ratio was the highest around 0 $^{\circ}C$ and the maximum frost heave pressure was observed when deformation ratio was less than 10% which was the stability state of soil freezing. The state had no relation with frost depth. Over freezing process was observed when drainage or suction freezing process was undergone. Drainage freezing process was observed if freezing velocity was high under confined pressure and suction frost process was occurred if the velocity was low under the same confined process.

• 한국재료학회지
• /
• 제9권8호
• /
• pp.817-824
• /
• 1999

$Al_2$$O_3$-SiC 화합물 분말이 $SiO_2$, A1 그리고 C 분말들을 원료분말로 하여 SHS(self-propagating High-temperature Synthesis)법에 의해 제조되었다. 원료 분말에서의 몰비, 성형압력, 반응물의 초기온도의 영향이 생성물과 연소과정에 대해 연구되었다. $SiO_2$/A1/C계의 자전연소합성은 낮은 연소온도 때문에 $400^{\circ}C$ 이상으로 예열되어야 한다. 연소반응의 결과로서 최종생성물의 순도는 반응물의 순도보다 높았다. 이 계에서 $SiO_2$:Al:C의 적당한 몰비는 3.0:4.0:6.0이었고, free carbon은 30min 동안 $650^{\circ}C$에서 배소함으로써 제거되었다. 본 연구에서 상압소결은 $1700^{\circ}C$에서 powder bed를 사용한 표본의 분해를 제어하고 치밀한 소결체를 얻는데 매우 효과적이었다. hot-pressing으로 생성된 소결체는 이론비교밀도의 약 98%이었다.

• 한국조경학회지
• /
• 제26권2호
• /
• pp.54-61
• /
• 1998

The subsurface environment of the root zone area can set the stae for "do or die" of the turfgrass plant. The good condition of the greens is verified by their physical properties. Therefore, this study was carried to evaluate on the existing green of Hwasan C.C. by undisturbed soil Core Anaysis. We completed the ISTRC SYSTEM BenchMarking of the undisturbed core samples taken from Green #1, Green #5, Green #9-"Best" area, and Green #9-"Stressed" area for the Hwasan C.C.. It was also our understanding that the greens were in "good" to "very good" conditioni. THe exception might be Green #9-"Stress" area, which was the stressed area. The stressed area was confined to a ridge across Green #9. The organic content test results comfirmed the development of organic layering in depth 0-2.5cm. For the amount of compaction in the upper root zones and te development of the green's respective organic layers, the infiltration rates were high in Green #1, Green #5, and Green #9 "Stressed" area. The depicted aerificaton hole might be the probable cause of the relatively high infiltraton rate. Green #9-"Best" area had a tested infiltration rate of 18.75cm/hr. Either this area had not been aerified, or the undisturbed sample did not contain a aerification cavity. The water retention capacity of the undisturbed samples was good. When the greens were first constructed, the original root zone mix had been relatively low water retention properties. And the bulk density and the porosity of the undisturbed samples were good. In the result, all the greens were similar except for the infiltration. Thus, we supposed that Green #9-"Stressed" area might be ainly influenced by the amount of irrigation water and the configuration of the green's surface. There had been a reduction in the amount of irrigation water as the water retention capacity in the greens was promoted. Especially, it had gradually become more of a problem as the green had matured in Green #9-"Stressed" area. Because Green #9-"Stressed" area was a ridge area. The reduction in the amount of irrigation water might be the probable cause of the stress in Green #9-"Stressed" area. Our final observation related to the soil texture and the particle size distribution of the sand. Though and sand contant of all the tested greens were good, the gravel content of them exceeded ISTRC Guidelines. In particle size distribution of the sand, the very coarse and the coarse content of all the tested greens exceeded, but the rest was insufficient. The stability is a function of the material retained on the 0.25mm mesh screen. But, the content of all the tested greens was very insufficient. Though all the greens was serviceable, the coarse root zone sands, such as the sand in the tested greens, tended to be "unstable". Thus, we recommend using a topdressing/aerification sand which should be more in line with ISTRC/USGA Guidelines.;unstable". Thus, we recommend using a topdressing/aerification sand which should be more in line with ISTRC/USGA Guidelines.ines.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.46-49
• /
• 2003

Cu have been widely used as signal transmission materials for electrical electronic components owing to its high electrical conductivity. However, it's size have been limited to small ones due to its poor mechanical properties, Until now, strengthening of the copper at toy was obtained either by the solid solution and precipitation hardening by adding alloy elements or the work hardening by deformation process. Adding the at toy elements lead to reduction of electrical conductivity. In this aspect, if carbon nanofiber is used as reinforcement which have outstanding mechanical strength and electric conductivity, it is possible to develope Cu matrix nanocomposite having almost no loss of electric conductivity. It is expected to be innovative in electric conduct ing material market. The unidirectional alignment of carbon nanofiber is the most challenging task developing the copper matrix composites of high strength and electric conductivity In this study, the unidirectional alignment of carbon nanofibers which is used reinforced material are controlled by drawing process in order to manufacture the intermediary materials for the carbon nanofiber reinforced Cu matrix nanocomposite and align mechanism as well as optimized drawing process parameters are verified via experiments and numerical analysis. The materials used in this study were pure copper and the nanofibers of 150nm in diameter and of $10~20\mu\textrm{m}$ In length. The materials have been tested and the tensile strength was 75MPa with the elongation of 44% for the copper it is assumed that carbon nanofiber behave like porous elasto-plastic materials. Compaction test was conducted to obtain constitutive properties of carbon nanofiber. Optimal parameter for drawing process was obtained by experiments and numerical analysis considering the various drawing angles, reduction areas, friction coefficient, etc Lower reduction areas provides the less rupture of cu tube is not iced during the drawing process. Optimal die angle was between 5 degree and 12 degree. Relative density of carbon nanofiber embedded in the copper tube is higher as drawing diameter decrease and compressive residual stress is occurred in the copper tube. Carbon nanofibers are moved to the reverse drawing direct ion via shear force caused by deformation of the copper tube and alined to the drawing direction.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3250-3259
• /
• 2022

A new approach to the use of rice straw as a difficult-to-recycle agricultural waste was proposed. Potassium aluminosilicate was obtained by spark plasma sintering as an effective material for subsequent immobilization of ¹³⁷Cs into a solid-state matrix. The sorption properties of potassium aluminosilicate to ¹³⁷Cs from aqueous solutions were studied. The effect of the synthesis temperature on the phase composition, microstructure, and rate of cesium leaching from samples obtained at 800-1000 ℃ and a pressure of 25 MPa was investigated. It was shown that the positive dynamics of compaction was characteristic of glass ceramics throughout the sintering. Glass ceramics RS-(K,Cs)AlSi₃O₈ obtained by the SPS method at 1000 ℃ for 5 min was characterized by a high density of ~2.62 g/cm³, Vickers hardness ~ 2.1 GPa, compressive strength ~231.3 MPa and the rate of cesium ions leaching of ~1.37 × 10^-7 g cm^-2·day^-1. The proposed approach makes it possible to safe dispose of rice straw and reduce emissions into the atmosphere of microdisperse amorphous silica, which is formed during its combustion and causes respiratory diseases, including cancer. In addition, the obtained is perspective to solve the problem of recycling long-lived ¹³⁷Cs radionuclides formed during the operation of nuclear power plants into solid-state matrices.