• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.358-364
• /
• 2009

This paper is to investigate the influence of driving patterns of slow and high speed vehicles on the performance of continuously regenerating diesel particulate filter(DPF) system matched with operating conditions in field application. The DPF performance test for field application was carried out for two identical DPFs installed to slow and high speed vehicles. A slow speed vehicle was selected among local buses which have driving patterns to repeat running and stop frequently, while a high speed vehicle was prepared to have long route of high speed over 60km/h like inter-city buses. In this test, the regeneration performance on the DPF of slow speed vehicle deteriorated because of high soot load index(SLI) in spite of same balance point temperature(BPT) distribution for high speed vehicle. The DPF of slow speed vehicle melted in the end because the rapid increase of back pressure caused high temperature over $1200^{\circ}C$ in the ceramic wall of DPF. The PM components like ash collected to the filter in the DPF were analyzed in order to investigate the cause of the defect and provide an operation performance of DPF system. In the result of the analysis, high levels of lubrication oil ash(Ca, Mg, P, Zn) were detected.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.6
• /
• pp.593-599
• /
• 2012

To analyze the effect of the track structure on the running performance of the railway vehicle, we studied on the vibration and ride characteristics of the high speed train. As results, vibration and ride level of high speed train on the concrete bed track is more reduced than on the ballast bed track. Peak-peak value of carbody vibration on the concrete bed track at 300km/h is half of the peak-peak value of carbody vibration on the ballast bed track. Ride level on the concrete bed track at 300km/h is same level as that on the ballast bed track at 250km/h. Thus, Vibration and ride performance of the high speed train on the concrete bed track is greatly improved compared with that on the ballast bed track.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1426-1428
• /
• 2000

A new block system - MAS (Moving Autoblock System) whose efficiency is higher than FAS(Fixed Autoblock System) in the loading capacity is required to accomodate the increasing transport volume. That MAS has higher efficiency has already been verified through various studies, especially in a line with different types of travelling trains. The efficiency of MAS for Korean high speed line with two different train model is analyzed by computer simulation. The results show that MAS is more efficient than FAS in the loading capacity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.81-87
• /
• 2017

This paper describes the dynamic behavior and enhancement of Korean high-speed trains. The tail vibration reduction method of the yaw damper installation method change, which was derived from previous research, was applied to the running test of high-speed train. In addition, the vibration reduction method for the entire vehicle was derived by a numerical method and its effect was confirmed by a running test. The improved design was applied to the double-deck high-speed train coaches and the commissioning proceeded without problems in dynamic behavior. Sensitivity analysis of the suspension parameters affecting the critical speed of Korean next-generation high-speed trains was performed and four design variables that greatly affected the critical speed were derived. These were in the order of the primary elastic joint x-directional stiffness, the secondary yaw damper series stiffness, the secondary lateral damper damping coefficient, and the carbody damper damping coefficient. By optimizing the design variables, the suspension parameter that improves the critical speed by 23.3% can be used in the commercial designs of Korean next-generation high-speed trains.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.1
• /
• pp.25-29
• /
• 2002

There is an increasing interest in high-speed signal processing in modern telecommunication and SC circuit, HDTV, ISDN. There are many methods of high-speed signal processing. This paper describes a design approach for the realization of high-frequency Op-amp in CMOS technology. A limiting factor in Op-amp based analog integrated circuits is the limited useful frequency range. this thesis will develop a CMOS op-amp architecture with improved gainband width product with this technique an op-amp will achieve up to 170MHz (CL=2pF) unity-gain frequency with a 1.2-micron design rule. This CMOS op-amp is particularly suitable for achieving wide and stable closed-loop band widths, such as required in high-frequency SC filters, high-speed analog circuits.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.14-20
• /
• 2015

A high-speed reduction transfer case is usually employed by an excavator, wheel loader, or bulldozer. When powerful torque is required in the case of climbing steep roads or towing heavy equipment, the high-speed reduction mode of the gearbox is used. Generally, a transfer case using a spur gear type with a speed reduction system has a speed reduction ratio of 1 to 1 or 2 to 1. However, the structure of a transfer case achieved at a high speed of 1 to 1 and a low speed of 4.5 or under 5.5 to 1 with the speed reduction by use of a planetary gear type with a speed reduction system was proposed in this study. By employing a planetary gear type with a speed reduction system, the compact structure of the transfer case was achieved, and the impact or the partial defect of gear teeth was eliminated.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.1
• /
• pp.18-27
• /
• 2002

This paper presents an implementation of digital high-performance speed sensorless control system of an induction motor drives with Direct Torque Control(DTC). The system consists of closed loop stator flux and torque observer, speed and torque estimators, two hysteresis controllers, an optimal switching look-up table, IGBT voltage source inverter, and TMS320C31 DSP controller board. The stator flux observer is based on the combined current and voltage model with stator flux feedback adaptive control for wide speed range. The speed estimator is using the model reference adaptive system(MRAS) with rotor flux linkages for speed turning signal estimation. In order to prove the suggested speed sensorless control algorithm, and to obtain a high-dynamic robust adaptive performance, we have some simulations and actual experiments at low(20rpm) and high(1000rpm) speed areas. The developed speed sensorless system are shown a good speed control response characteristic, and high performance features using 2.2[kW] general purposed induction motor.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2203-2205
• /
• 2003

In this thesis, it is a purpose to carry out speed control of DC servo motor without using encoder and the resolver which are speed sensor of DC servo motor and it should use estimate algorithm or observer and must assume a speed in order to control speed sensorless. Therefore, high gain observer was designed to estimate rotor speed of DC servo motor and it carries out speed control from the feedback of the speed that assumed done in the thesis. Also, implementation used easy PI controller in speed-controller of DC motor though it was simple. It is compared estimate performance of Luenberger and high gain observer in a way of computer simulation in order to verify performance of the high gain observer which proposed in this thesis, and proved excellency of the high gain observer. And the thesis proved that smooth speed sensorless control of DC servo motor was implemented in invariable driving.

• Journal of ILASS-Korea
• /
• v.16 no.3
• /
• pp.126-133
• /
• 2011

In HCCI Engine, combustion is affected by change of compression speed corresponding to engine speed. The purpose of this study is to investigate the mechanism of influence of engine speed on HCCI combustion characteristics by using numerical analysis. At first, the influence of engine speed was shown. And then, in order to clarify the mechanism of influence of engine speed, results of kinetics computations were analyzed to investigate the elementary reaction path for heat release at transient temperatures by using contribution matrix. In results, as engine speed increased, in-cylinder gas temperature and pressure at ignition start increased. And ignition start timing was retarded and combustion duration was lengthened on crank angle basis. On time basis, ignition start timing was advanced and combustion duration was shortened. High engine speed showed higher robustness to change of initial temperature than low engine speed. Because of its high robustness, selecting high engine speed was efficient for keeping stable operation in real engine which include variation of initial temperature by various factors. The variation of engine speed did not change the reaction path. But, as engine speed increased, the temperature that each elementary reaction would be active became high and reaction speed quicken. Rising the in-cylinder gas temperature of combustion start was caused by these gaps of temperature.

• Journal of the Korean Society for Railway
• /
• v.7 no.4
• /
• pp.332-338
• /
• 2004

The two projects about the high speed train have been performed in Korea, one project is the commercial run of high speed train(KTX) from Seoul to Busan and the other is the development of original high speed train(HSR 350x). As the successful results, the service run of KTX had been launched on the 1st of April, 2004 and HSR 350x had been fabricated in June, 2002 and has been tested in the Kyoungbu line and Honam line since then. The railway has the track irregularities which cause vibrations, such as rail joints, turnout, level crossing, transition curves and super-elevation ramps, and variations in the track level(z-axis) and the gauge(y-axis). Generally, the ride comfort for railway is evaluated by using the vibrations. In this paper, the ride comfort indices according to mc 513R and ISO 10056 have been reviewed when the high-speed trains are operated on both Kyoungbu line and Honam line. Also, the ride characteristics for KTX and HSR 350x on the high speed line and the conventional line have been analyzed and evaluated. The results show that the high-speed train has no problem from the viewpoint of the comfort ride on the high speed line and the conventional line and the ride index for HSR 350x is same as that for KTX in the high speed(300 km/h).