• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.330-336
• /
• 2001

Water heat transfer experiments were carried out in a uniformly heated annulus with a wide range of pressure conditions. The local heat transfer coefficients for saturated water flow boiling have been measured just before the occurrence of the critical heat flux (CHF) along the length of the heated section. The trends of the measured heat transfer coefficients were quite different from the conventional understanding for the heat transfer of saturated flow boiling. This discrepancy was explained from the nucleate boiling in the liquid film of annular flow under high heat flux conditions.

• 한국농공학회지
• /
• 제45권2호
• /
• pp.126-137
• /
• 2003

The feasibility study of UV-disinfection system was performed for disinfection of effluent from wastewater treatment plant. Three low-pressure UV lamps of 17, 25, and 41 W were examined with various flow rates. Low-pressure UV lamps of 17W were examined with various turbidity, DOM (dissolved organic matter), and SS (suspended solid). The pilot plant was a flow-through type UV-disinfection system, and the range of exposure time varied from 5 to 40 seconds, turbidity from 0 to 40 NTU, DOM from 0 to 30 mg/L, and SS from 10 to 40 mg/L. The 41W lamp demonstrated complete disinfection showing no survival ratio in all the experimental conditions, and generally 17W and 25W lamps also showed high removal ratio over 97%. For the same UV dose (UV intensity times exposure time), high intensity-short exposure conditions showed better disinfection efficiency than low intensity-long exposure conditions. While the effects of turbidity and DOM were not apparent, the effects of SS was significant on the disinfection efficiency which indicates that SS control before UV-disinfection appears to be necessary to increase removal efficiency. Considering characteristics of effluent from existing wastewater treatment plants, cost-effectiveness, stable performance, and minimum maintenance, the flow-through type UV-disinfection system with high intensity and low-pressure lamps was thought to be a competitive disinfection system for wastewater reclamation.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1998년도 제6회 하계 Workshop (98 한국막학회, 국립환경연구원 국제 Workshop, 수자원 보전과 막분리 공정)
• /
• pp.155-170
• /
• 1998

1. The flux for hydrophilic CA membrane is higher than that for hydrophobic PES membrane at any operating conditions. The difference in bpth fluxes becomes greater as the water recovery is lower. 2. Backwash pressure should be more than twice as high as filtration pressure in order to maintain the higher flux. Backwash frequency is independent of the flux when the UF is operated under the same water recovery. 3. The relatively lower crossflow velocity of around 0.1 m/s would be appropriate because of the lower energy consumption per treated water. 4. The membrane fouling occurring at high turbidity and high concentration of organic compounds in raw water can reduce the flux and increase the removal of the organic compounds. 5. It is confirmed by the pilot plant testing that the UF by using the CA membrane module was well applicable to the drinking water treatment.

• Journal of Biosystems Engineering
• /
• 제23권5호
• /
• pp.445-456
• /
• 1998

This study was carried out to evaluate the performance of a medium scale rice polisher of 2.5 t/h and to improve its performance for producing the clean rice with high quality. The maximum internal pressure, broken rice ratio. whiteness in the rice polisher were investigated, and the effects of outlet resistance, water spraying rate, shaft revolution speed and rice moisture content on the polishing performance were analyzed to find out proper operating conditions. The conclusions of this study were as follows: 1. In the performance evaluation of the polisher, the broken rice ratio increment of 0.1%, the max. internal pressure of about 11 N/${cm}^2$, and whiteness increment of 2.2~3.7 resulted at the conditions of 20 PS driving power, 950 rpm, 150 cc/min water spraying rate, 44.1 Nㆍcm outlet resistance and about 15% rice moisture content. 2. Though max. internal pressure and whiteness at the 17% rice moisture content were higher than those at the 15% moisture content under the same operating conditions of the polisher, but the broken rice rate at the 17% moisture content was absolutely low compared with that at 15% moisture content. The water spraying effect to reduce broken rice and to increase whiteness was much significant at the 15% moisture content not significant at 17% moisture content. 3. The main parameter of the performance was outlet resistance, and low resistance of about 44.1 Nㆍcm was recommended at the polisher. 4. The proper water spraying rate in the polisher was about 150 cc/min. 5. As the shaft revolution speed decreased from 950 rpm and 800 rpm to 650 rpm, the broken rice ratio increased and whiteness decreased. 6. As the driving power of the polisher increased from 20 PS to 30 PS, the max. internal pressure decreased by about 1~2.5 N/${cm}^2$ and whiteness increased by about 1~2, but the broken rice rate was not changed. 7. The proper operating conditions of the polisher seemed to be the revolution speed of 800-950 rpm, the water spraying rate of about 150 cc/min, the oulet resistance of about 44.1 N.cm and 30 PS driving power.

• 한국식품조리과학회지
• /
• 제24권2호
• /
• pp.188-197
• /
• 2008

This study was carried out to determine the optimal cooking conditions for various rice cultivars (Ilpoom, Saechucheong, Sindongjin, and Sura-top rice) using trial preparations with different soaking times (0, 30, and l20min) and cooking equipment (electric pressure cookers, electric cookers, gas pressure cookers, iron pots, and stone pots). In adddition, the texture and sensory characteristics of the rice prepared with the electric pressure cookers, gas pressure cookers, and stone pots were analyed. The results showed that the moisture, amylose and physicochemical compositions of the four rice varieties were similar. According to RVA, the Sura, cultivar had generally high viscosity, and the Ilpoom, cultivar presented the highest hot and peak viscosities. Saechucung had the highest initial gelatinizing temperature and Sindongjin showed the greatest setback. The optimal amounts of added water as well as heating conditons were dependent on the rice varieties, soaking times, and cooking equipment. A longer soaking time reduced the hardness of the cooked rice, amount of added water, and the heating time. The pressure cooking equipment provided the best cooked rice texture, reduced the affect of the soaking time, and decreased the heating time. In general, all the variaties of cooked rice had high overall acceptability, which tended to increase when the rice was soaked for 30min prior to cooking, had a 1.2-fold amount of water to rice added, and was cooked in the pressure equipment.

• Nuclear Engineering and Technology
• /
• 제50권7호
• /
• pp.1173-1183
• /
• 2018

Transient fluid velocity and pressure fields in a pressurized water reactor (PWR) steam generator (SG) secondary side during the blowdown period of a feedwater line break (FWLB) accident were numerically simulated employing the saturated water flashing model. This model is based on the assumption that compressed water in the SG is saturated at the beginning and decompresses into the two-phase region where saturated vapor forms, creating a mixture of steam bubbles in water by bulk boiling. The numerical calculations were performed for two cases of which the outflow boundary conditions are different from each other; one is specified as the direct blowdown discharge to the atmosphere and the other is specified as the blowdown discharge to an extended calculation domain with atmospheric pressure on its boundary. The present simulation results obtained using the two different outflow boundary conditions were discussed through a comparison with the predictions using a simple non-flashing model neglecting the effects of phase change. In addition, the applicability of each of the non-flashing water discharge and saturated water flashing models for the confirmatory assessments of new SG designs was examined.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.169-174
• /
• 2006

본 연구는 재생냉각형 고압 축소형 연소기 설계에 관한 것으로 이 연소기를 제작하기 전에 열유속측정을 위한 물냉각 고압 축소형 연소기를 제작하였다. 물냉각 고압 축소형 연소기의 연소시험결과 높은 연소성능 및 냉각성능이 검증된 설계 조건을 얻었고 이를 바탕으로 재생냉각형 고압 축소형 연소기의 형상을 설계하였다. 설계된 연소기의 형상은 제작이 완료된 후 연소시험을 수행하여 실용성을 검증 할 예정이다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.144-145
• /
• 2021

This study analyzed the cases of cracks in piles due to the use of followers under construction conditions where water exists inside the piles, and confirmed whether the piles were cracked through a field test simulating the construction conditions in which water pressure inside the piles was generated by a hammer. According to the construction case, under the construction condition where the pile length is 20% to 30% shorter than the drilled length, about 80% cracks occur, so there is a high possibility of cracking due to water inside the pile. A field test was conducted to confirm the type of pile failure due to hammer under the construction condition in which water exists inside the pile. The pile head was not destroyed by the compressive load, and one or more longitudinal cracks occurred along the PC steel wire. The closed end pile generates water pressure by hammer. the follower and cushion(compression plywood) must be drilled at least 0.4D. It is expected that improved quality control will be possible as the water pressure inside the pile is reduced.

• 대한환경공학회지
• /
• 제22권7호
• /
• pp.1183-1191
• /
• 2000

UF를 이용한 용존성 유기물질 제거시 파울링을 저감할 수 있는 운전인자를 알아보기 위하여 pilot plant 규모의 중공사형 UF막을 다양한 실험조건에서 운전하였다. 연구결과 유입압력이 높으면 막표면에 생성된 케익의 압밀화화 흡착이 증대되어 막간차압의 증가폭과 투과플럭스 감소폭이 커졌다. 역세효과는 역세압을 높여서 유효압을 증가시키거나 역세빈도를 짧게 할수록 좋았다. 유효압이 증가할수록 역세후 막표면의 오염물질이 감소하고 역세빈도가 짧을수록 재순환수의 오염물질농도가 감소하기 때문이다. 파울링과 상관성이 높은 운전인자는 역세압, 유입압력, 회수율, 누적투과플럭스, 투과플럭스였다. 이 중 역세압력이 파울링과 가장 밀접한 관계가 있었고 유입압력이 두 번째로 상관성이 높았다. 이것으로 보아 막표면의 케익층 압밀화와 흡착의 원인이 되는 압력이 파울링과 밀접한 관계가 있는 것으로 생각된다.

• 한국산학기술학회논문지
• /
• 제10권11호
• /
• pp.3287-3295
• /
• 2009

본 연구는 강우재현장치를 제작하고, 화강암질 풍화토로 조성된 모형사면에 강우 및 사면조건에 따라 모형실험과 수치해석을 실시하였다. 모형실험에서 계측된 체적함수비와 간극수압의 변화특성을 분석하였으며 또한 수치해석 결과와 비교하였다. 체적함수비는 강우강도가 크고 사면경사가 급할수록 한계값에 도달하는데 짧은 시간이 소요되는 반면 강우강도가 작고 사면경사가 완만할수록 많은 시간이 소요되는 것으로 나타났다. 강우강도가 작고 강우지속시간이 짧을수록 더 큰 부의 간극수압을 나타내고 회복하는 시간도 짧은 것으로 나타났다. 이와 반면 강우강도가 크고 강우지속시간이 길수록 부의 간극수압을 회복하는데 오랜 시간이 소요되는 것으로 나타났다. 강우재현 모형실험과 수치해석을 수행한 결과 체적함수비와 간극수압의 분포경향이 유사하게 나타났다. 그러나 체적함수비는 최대 5% 정도, 간극수압은 최대 3kPa 정도의 차이를 보였다.