• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.76-83
• /
• 2013

This study investigated the effect of bonding temperature and holding time on microstructures and mechanical properties of diffusion bonded joint of Haynes230. The diffusion bonds were performed at the temperature of 950, 1050, and $1150^{\circ}C$ for holding times of 30, 60, 120 and 240 minutes at a pressure of 4MPa under high vacuum condition. The amount of non-bonded area and void observed in the bonded interface decreased with increasing bonding temperature and holding time. Cr-rich precipitates at the linear interface region restrained grain migration at $950^{\circ}C$ and $1050^{\circ}C$. However, the grain migration was observed in spite of short holding time due to the dissolution of precipitates to base metal in the interface region at $1150^{\circ}C$. Three types of the fracture surface were observed after tensile test. The region where the coalesce and migration of grain occurred much showed high fracture load because of base metal fracture whereas the region where those did less due to the precipitates demonstrated low fracture load because of interface fracture. The expected fracture load could be derived with the value of fracture area of base metal ($A_{BF}$) and interface ($A_{IF}$), $Load=201A_{BF}+153A_{IF}$. Based on this equation, strength of base metal and interface fracture were calculated as 201MPa and 153MPa, respectively.

• Composites Research
• /
• 제36권3호
• /
• pp.193-198
• /
• 2023

선박 경량화와 관련하여 기존 복합재료 및 3D 프린트 복합재료를 적용하는 연구가 활발히 진행되고 있다. 염수 환경에 대한 내부식성과 경량화 특성이 있는 복합재료와 우수한 생산성을 가지는 3D 프린팅 기술을 연계한 3D 프린트 복합재료의 선박 및 해양구조물 적용 가능성을 확인하기 위해 시험을 진행하였다. 본 논문에 사용된 3D 프린트 복합재료를 선박 및 해양구조물에 적용하기 위해서는 해양환경에서 노출될 수 있는 온도 환경 영향을 고려해야 한다. 따라서 해양 환경에서 노출될 수 있는 온도인 저온(-50℃), 상온(20℃), 고온(50℃) 환경에서 Carbon + Onyx, Carbon + Nylon, HSHT glass + Onyx, HSHT glass + Nylon 소재의 시편으로 인장시험을 진행하였다. 인장시험 결과, Carbon + onyx 시편이 가장 높은 인장강도를 보였고 HSHT glass + onyx 시편이 가장 높은 인장 변형률을 보였다. 또한 인장 시험 결과 시편을 분석하여 다양한 온도 환경에 노출된 3D 프린트 복합재료 시편의 파손 형상에 대해 분석하였다.

• 연구논문집
• /
• 통권33호
• /
• pp.167-174
• /
• 2003

Alloy 713LC was developed to improve the tensile strength and ductility by reducing the carbon content of Alloy 713C. As Alloy 713LC was designed to minimize the mechanical property change with process conditions, it is generally utilized in the parts which have thick and thin sections simultaneously. In the thick and the thin sections, quite different properties are required. Consequently it is essential to crucially control the local mechanical properties of a parts by optimizing the process condition and heat treatment. In this research, high temperature mechanical properties including creep-rupture and strain-control low cycle fatigue were investigated together with the microstructural variations with heat treatment. Failure mechanism was also analyzed by observing the fracture surface to correlate the variation of mechanical properties with the microstructural change.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 춘계학술대회 논문집
• /
• pp.282-288
• /
• 2001

This paper deals with determining the proper friction welding condition and analyzing various mechanical properties of friction welded joints of the bladepart heat resisting steel(STD11) for cold die punch to the shank part alloy steel(SCM440). And the in-process real-time weld quality evaluation technique by acoustic emission during friction welding of STD11 to SCM440 steels with higher confidence and reliability has been much required even though it might be the first trial approach for developing it. Also, the high temperature properties of STD11-SCM440 weld were considered in this paper.

• 한국주조공학회지
• /
• 제17권5호
• /
• pp.450-457
• /
• 1997

Effects of Ti addition and homogenizing heat treatment on the mechanical properties in Cu-Zn-Al alloy (high strength yellow brass) were investigated. Grain refinement was successfully achieved by Ti addition. The microstructure, which was composed of island or fine feather-like branched Ti compounds was changed to feather-like eutectic microstructure as the content of Ti increased. The highest hardness value was obtained for 0.5 wt.% Ti specimen and the second was Ti non-added specimen in as-cast condition. The highest tensile strength was obtained for 0.5 wt.% Ti specimen. Because of the presence of cast defects and worse castability, tensile strength decreased as the content of Ti increased. Elongation increased with increasing homogenizing time and temperature; remarkable increase was obtained for $400^{\circ}C$ homogenizing temperature in the 0.5 wt.% Ti specimen. For $500^{\circ}C$ and $600^{\circ}C$ homhgenizing, temperature, high elongation was obtained in 2 and 4 wt.% Ti specimen.

• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.3096-3103
• /
• 2000

High temperature material properties of a welded joint were experimentally studied. Tensile and creep properties were measured for each part of weld metal. HAZ(heat affected zone) and parent metal at 538$^{\circ}C$. HAZ metal was obtained by a simulated heat treatment. Results showed that the order of tensile strength is weld>HAZ> parent both at 24$^{\circ}C$ and at 538$^{\circ}C$. Creep resistance was also the highest for weld metal and lowest for parent metal. Creep rupture life curves were obtained and converted to Monkman-Grant relation which is useful for life assessment. Use of the data obtained in this study is discussed.

• 대한금속재료학회지
• /
• 제49권9호
• /
• pp.671-677
• /
• 2011

Steel columns used in steel buildings are inclined to lose their strength when exposed to severe fire conditions, so fire resistance is required in most countries to protect against loss of life and building collapses. In Korea, the fire resistance of columns can be obtained by the fire test defined in KS F 2257-1, 7. The fire resistance of a steel column should be evaluated in terms of the column's conditions, such as various section types (H-section, hollow-section), the column's length and boundary conditions, and whether it is fixed or hinged. However, fire testing of steel columns is usually conducted on one standard-sized H-section over 3,000 mm, and the result is used as the column's fire resistance. This is not a reasonable way to ensure that a building can withstand fire conditions. In this study, to evaluate the possibility of calculating the fire resistance of steel columns with material properties of high tensile strength of SS 400, both load-bearing fire tests and calculation of steel temperatures were carried out. The results of temperature calculation were very similar to those obtained by fire test.

• Journal of the Korean Wood Science and Technology
• /
• 제32권6호
• /
• pp.67-73
• /
• 2004

The influence of liquefied wood (LW) on the mechanical and thermal properties of liquefied wood-polymer composites (LWPC) was investigated in this study. The thermal behaviors of LWPC were characterized by means of thermogravimetric (TGA) and differential scanning calorimetric (DSC) analyses. LW showed significant effects on the mechanical strength properties. The increase of flexural MOE and Young's modulus was related to the increase of stiffness of LWPC. The effect of LW was also significant on the flexural and tensile MOR. The impact strength decreased with the increase of LW application level. With the increased stress concentration by the poor bonding between LW and polymer, the impact strength of LWPC decreased, compared with that of high-density polyethylene (HDPE). The thermal stability of LWPC decreased with the increase of LW content up to 40%. The melting temperature of HDPE decreased with the increase of LW loading level. Enthalpy of HDPE also decreased with the addition of LW. This study proves the thermal stability necessary for the consolidation of composition materials.

• 소성∙가공
• /
• 제30권2호
• /
• pp.91-98
• /
• 2021

The present study deals with the microstructure and mechanical properties of 700 MPa-grade high-strength seismic resistant reinforced steel bars fabricated by various TempCore process conditions. For the steel bars, in the surface region tempered martensite was formed by water cooling and subsequent self-tempering during TempCore process, while in the center region there was ferrite-pearlite or bainite microstructure. The steel bar fabricated by the highest water flow and the lowest equalizing temperature had the highest hardness in all regions due to the relatively fine microstructure of tempered martensite and bainite. In addition, the steel bar having finer microstructures as well as the high fraction of tempered martensite in the surface region showed the highest yield and tensile strengths. The presence of vanadium precipitates and the high fraction of ferrite contributed to the improvement of seismic resistance such as high tensile-to-yield strength ratio and high uniform elongation.

• 소성∙가공
• /
• 제31권2호
• /
• pp.73-80
• /
• 2022

In this study, a developed Mg-5Bi-2Al-0.4Mn (BAM520, wt%) alloy was successfully extruded at an extremely high speed of 70 m/min. Microstructural evolution during extrusion and the microstructural characteristics and tensile properties of the very-high-speed extruded BAM520 alloy were then investigated. The homogenized BAM520 billet contained only thermally stable Mg₃Bi₂ phase particles without any Mg₁₇Al₁₂ phase with a low melting temperature. Therefore, the BAM520 alloy exhibited excellent extrudability. The very-high-speed extruded BAM520 alloy had a completely recrystallized grain structure and a typical basal fiber texture. Despite the extremely high extrusion speed of 70 m/min, the extruded BAM520 alloy had a high ultimate tensile strength of 280 MPa due to combined strengthening effects of a small grain size, numerous fine Mg₃Bi₂ particles, and strong basal texture.