• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.274-280
• /
• 2000

To analyze the resistance of the bottom trawl which is composed with 6 seams net, the field experiment was carried out on the sea near Kokunsan Is., western sea of Korea. The resistance was respectively measured in the otter board and the net according to the change of warp length and towing speed. The results obtained are summarized as follows : 1. Total resistance of the test trawl gear are slightly increased according to the length of warp. 2. The resistance of net is increasing a little according to the length of warp, but it is expressed. $$ R_n/=10 \frac{d}{\ell}$representatively. 3. The resistance of otter board can be expressed $Rb=1810_{\upsilon}^0.8.$ 4. Comparing with the value of measuring resistance and Koyama formula resistance by the length of warp respectively, the resistance of test trawl gear is high in the slow towing speed, and the resistance of Koyama formula is high in the fast towing speed, and that the cross-point of the both line between the resistance of the test net and Koyama formula is moved to high according to the increment of warp length.

• Proceedings of the KAIS Fall Conference
• /
• 2001.11a
• /
• pp.99-103
• /
• 2001

Though the research and the development in the field of machine tool was focused on high precision and high speed machine these days, traditional gear reduction device has been used to increase the cutting force which was transmitted from power source, motor In this study, analysis of 2 step gear reducer used in machining center spindle was carried out by using APM WinMachine which is commercial software for the analysis of machine element and system. For the analysis of this device, first of all, the analysis of power source and the transmitting of it were carried out. Then, machine elements like gear, shaft, bearing, and the forth, was analyzed in the view point of life time, static strength, stiffness, fatigue failure, etc. Consequently, we can estimate them and introduce new idea of the design modification of reduction device by this study.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2769-2772
• /
• 2003

This paper presents results of the development of the Turbo-generator system with structure which is HSG(High Speed Generator) installed to high speed gas-turbine engine directly. Turbo-generator with high speed motor-generator directly has many advantages aspects of weight, size, lubrication system and complexity of the system compared of conventional turbo-generator system with gear-box. But because of direct high speed operation of the high speed generator, we have to need stable high speed motor driving algorithm for perfect engine ignition when gas turbine starting. Also we have to need design of the PCU(Power Conditioning Unit) for converting high speed AC output power to conventional AC power or needed DC power.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.406-408
• /
• 1996

This paper describes the BLDC motor which is applicated for a top front loading domestic washing machine. This motor is adopted direct drive washing machine without gear-belt-pulley system. Because gear box is removed, machine volume and noise are reduced. Moreover mechanical troubles in gear box are removed. Realization of variable speed region through of PWM control and high speed is able to efficient washing and spinning.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.508-511
• /
• 2008

The most landing gear use oleo-pneumatic shock strut to absorb the impact energy during touchdown. The shock strut is composed of the oil damper and the gas spring, especially the oil damper provides resistance force which is proportional to the square of landing speed. In case of high landing speed, the abnormal peak load can be occurred and transferred to the airframe structure. To prevent this, the pressure-relief valve is used to limit the damping force under the specific level. In this paper, it is presented the design process to find optimal damping and analysis results using pressure-relief valve.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.70-75
• /
• 2011

Nowadays, modern gearboxes are characterized by high torque load demands, low running noise and compact design. Also durability of gearbox is specially a major issue for the industry. For the gearbox which used in wind turbine, gear transmission error(T.E.) is the excitation that leads the tonal noise known as gear whine, and radiated gear whine is also the dominant source of noise in the whole gearbox. In this paper, tooth modification for the high speed stage is used to compensate for the deformation of the teeth due to load and to ensure a proper meshing to achieve an optimized tooth contact pattern. The gearbox is firstly modeled in Romax software, and then the various combination analysis of the tooth modification is presented by using Windows LDP software, and the prediction of transmission error under the loaded torque for the helical gear pair is investigated, the transmission error, contact stress, root stress and load distribution are also calculated and compared before and after tooth modification under one torque condition. The simulation result shows that the transmission error and stress under the loads can be minimized by the appropriate tooth modification.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.5
• /
• pp.363-369
• /
• 2004

Vibration/noise analysis as well as strength of gear teeth, roller bearing life. joural bearing design are considered in order to develop the high-speed machine centrifugal pump which had a speed increaser. A Campbell diagram, in which the excitation sources caused by the mass unbalance of the rotors and the transmitted errors of the gearing are considered. shows that. at the operating speed. there are not the critical speed. A high-speed machine centrifugal pump was made in order to evaluate developed speed increaser. Also, strict API standard were introduced for reliability evaluation of developed speed increaser, and performance evaluation were carried out. The result that evaluation items about bearing vibration, shaft vibration, noise, and lubrication temperature were selected, and were tested. a high-speed machine centrifugal pump were able to know what were satisfied with API standard all.

• Journal of Energy Engineering
• /
• v.24 no.1
• /
• pp.88-96
• /
• 2015

Gear pump has a simple structure high reliability, easy operation and maintenance, widely used as a source of hydraulic system of hydraulic. In general, the gear pump was designed using variety of variables, the variables through the analysis of the mass flow rate and efficiency. In this paper, three-dimensional flow of the gear pump, in order to produce the optimal design of product, analysis was performed by using commercial software ANSYS v15.0 CFX. And then, combination of design parameters selected by ANSYS was carried out to confirm the simulation result. The efficiency and mass flow rate of the gear pump were studied by varying its rotational speed and the clearance between the gear tip and the housing. In the simulation results, as the rotational speed were increased, the average mass flow rate and efficiency increased. Furthermore, as the clearance between the gear tip and the housing was increased, the average mass flow rate and efficiency decreased.

• Journal of Institute of Convergence Technology
• /
• v.4 no.2
• /
• pp.11-15
• /
• 2014

Magnet gear transfers a high speed torque of the driving side to a low speed following side. Of course, the torque is amplified as much as a ratio between pole number of magnet gears constituting both sides through ferromagnet modulator. However, the parameters of the overall magnetic system influence the transmitting torque strongly. They include a pole number of permanent magnet, magnet thickness, reducing ratio, harmonic modulator thickness, and open ratio etc. In this paper, the influences of the parameters are analyzed using finite element method tool. By comparison, a desirable design specification is proposed, including a recommended modulator pattern.

• Journal of Power System Engineering
• /
• v.11 no.4
• /
• pp.65-71
• /
• 2007

According to the survey, abnormal condition of the system is the main source for interrupting an elevator service, especially faults in worm gears used for the traction machine. Worm gear is popularly used in traction machine for middle and low speed elevators. Elevators need high reliability and stability, because they are closely related to human life. Usually, traction machine is applied to drive the elevators that have height about 35 m and it is an important mechanical unit for riding quality in elevators. There are some research results about types of vibration fault for worm gear in International Association Elevator Engineers (IAEE). But this study concerns with diagnosis of various faults in elevator worm gear using vibration signal. The analysis of fault characteristics is compared with previous researches in traction machine.