• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.583-588
• /
• 2005

Indium tin oxide (ITO) is a commonly used conducting transparent oxide film (CTO) used in flat panel display applications. Direct write laser ablation is sometimes employed for ITO patterning and it is important that the substrate material and remaining ITO be affected as little as possible by the laser ablation. In this investigation, femtosecond laser ablation of ITO was studied to identify laser processing parameters which cleanly ablated ITO with a minimum of damage to a glass substrate and surrounding ITO. The Ti:Sapphire chirp pulse amplified femtosecond laser used for the experiments had a wavelength of 775nm and produced pulses with a duration of 150fs at a rate of 2 kHz. Ablation was carried out at a sufficiently high panel scanning speed that single ablation spots could be studied. The pulse energy was adjusted to determine feasible spot diameters and depths which could be ablated into the ITO without damaging the glass substrate. Next, ablation of lines without glass damage was also demonstrated. Experiments were also performed with a high repetition rate (100kHz) femtosecond laser.

• 대한조선학회지
• /
• 제9권2호
• /
• pp.43-48
• /
• 1972

Inertia friction welding, a relatively recent innovation in the art of joining materials, is a forge-welding process that releases kinetic energy stored in the flywheel as frictional heat when two parts are rubbed together under the right conditions. In a comparatively short time, the process has become a reliable method for joining ferrous, and dissimilar metals. The process is based on thrusting one part, attached to a flywheel and rotating at a relatively high speed, against a stationary part. The contacting surfaces, heated to plastic temperatures, are forged together to produce a reliable, high-strength weld. Welds are made with little or no workpiece preparation and without filler metal or fluxes. However, In order to obtain a good weld, the determination of the optimum weld parameters is an important problem. Especially, because the amount of the flywheel mass will be determined according to the initial rotating velocity values at the constant thrust load, the initial rotating velocity is an important factor to affect a weld character of the inertia-welded IN713C-SAE8630, which is used for the wheel-shafts of turbine rotors or turbochargers, exhausting valves, etc. In this paper, the effects of initial rotational velocity on a weld character of inertia-welded IN713C-SAE8630 was studied through considerations of weld parameters determination, micro-structural observations and tensile tests. The results are as the following: 1) As initial rotating velocity was reduced to 267 FPM, cracks and carbide stringers were completely eliminated in the micro-structure of welded zone. 2) As initial rotating velocity was reduced and flywheel mass was increased correspondingly, the maximum welding temperatures were decreased and the plastic working in the weld zone was increased. 3) As initial rotating velocity was progressively decreased and carbides were decreased, the tensile strengths were increased. 4) And also the fracture location moved out of the weld zone and the tensile tests produced, the failures only in the cast superalloy IN713C which do not extend into the weld area. 5) The proper initial rotating velocity could be determined as about 250 thru 350 FPM for the better weld character.

• Tribology and Lubricants
• /
• 제29권2호
• /
• pp.105-110
• /
• 2013

Refrigeration and air-conditioning compressors used in home appliances, including refrigerators and air conditioners, are typically hermetic-type reciprocating compressors. Because the shell is sealed by welding, it should be designed to have a semi-permanent life. The energy consumption of a hermetic-type reciprocating compressor is low, but because it operates continuously to maintain a constant temperature inside the refrigerator, it has a certain base load. In this type of compressor, the driving motor operates at a high speed (about 3,000 - 3,600 rpm), which causes valve damage, friction, wear, and high-frequency noise. Many studies have been conducted to solve these problems. To enhance the reliability and efficiency of the reciprocating compressor, the design conditions and operating environment of journal bearings should be considered. Dynamic behavior analysis should be carried out in terms of the discharge pressure. The results showed that the load (discharge pressure) increases in the forward lookup zone and decreases in the backward lookup zone. When the revolution speed is increased, the maximum load decreases in the region where the maximum load operates.

• 비파괴검사학회지
• /
• 제20권6호
• /
• pp.562-567
• /
• 2000

발전 및 산업설비에 사용되는 많은 압력용기는 저합금강을 사용하여 제작되고 있다. 압력용기의 내면은 부식이 미치는 영향을 최소화하기 위하여 오스테나이트계 스테인리스강으로 덧살용접을 하고 있으나, 용접층간의 계면에서 발생하고 있는 박리균열은 압력용기의 신뢰성에 중요한 변수가 되고 있다. 본 연구에서는 DSP를 사용하여 오버레이 용접부를 고속으로 검사할 수 있는 C-scan 시스템을 개발하였다. 본 시스템은 신호 처리부 (오실로스코프, 펄서/리시버, 디지타이저, DSP), 스캐너, 프로그램 및 위치 제어부로 구성되어 있다. 개발된 시스템을 사용하여 실제 오버레이 용접부에 대한 초음파검사를 실시한 결과 고속으로 신뢰성 높은 검사결과를 얻을 수 있었다.

• 한국산학기술학회논문지
• /
• 제15권10호
• /
• pp.5933-5938
• /
• 2014

본 연구에서는 Atos 60의 시험편에 혼합가스의 변화에 따른 FCA용접을 하였고, 용접특성 분석 위하여 용접공정상의 실시간 모니터링 시스템과 용접 후 기계적 성질을 평가 하였다. Ar 80%+$CO_2$ 20% 혼합하고 낮은 속도로 용접한 경우 가장 미려한 비드와 스패터 발생이 적게 나타났으며, 반면 $CO_2$ 100%인 경우 스패터가 많이 발생하는 것을 확인하였다. 정상단락이 발생하는 저전류 영역으로 혼합가스의 사용에 대한 스패터 발생을 확인 할수 있는 조건이며, $CO_2$ 100%인 경우 각층의 단락율은 약 2배 이상 높았고, Peak의 분포가 많은 아크의 불안정 상태로 나타났다. 인장시험결과 Ar 80%+$CO_2$ 20%, Ar 90%+$CO_2$ 10%, $CO_2$ 100%의 항복강도는 각각 511MPa, 507MPa, 469MPa 이었으며, $CO_2$ 100%의 항복강도 보다 각각 약 8.9% 8.1% 향상되었다. 인장강도는 각각 622MPa, 609MPa, 581MPa로 $CO_2$ 100%의 인장강도 보다 각각 약 7.0%, 4.8% 향상되었다.

• 마이크로전자및패키징학회지
• /
• 제24권1호
• /
• pp.83-90
• /
• 2017

본 연구에서는 미세피치 패키지 적용을 위한 기초 실험으로 thin ENEPIG(Electroless Nickel Electroless Palladium Immersion Gold) 도금층을 형성하여 솔더링 특성을 평가하였다. 먼저, Sn-3.0Ag-0.5Cu (SAC305) 솔더합금에 대한 thin ENEPIG 도금층의 젖음 특성이 평가되었으며, 순차적인 솔더와의 반응에 대한 계면반응 및 솔더볼 접합 후 고속 전단 시험을 통한 접합부 기계적 신뢰성이 평가되었다. 젖음성 시험에서 침지 시간이 증가함에 따라 최대 젖음력은 증가하였으며, 5초의 침지 시간 이후에는 최대 젖음력이 일정하게 유지되었다. 초기 계면 반응 동안에는 $(Cu,Ni)_6Sn_5$ 금속간화합물과 P-rich Ni 층이 SAC305/ENEPIG 계면에서 관찰되었다. 연장된 계면반응 후에는 P-rich Ni 층이 파괴 되었으며, 파괴된 P-rich Ni 층 아래에는 $(Cu,Ni)_3Sn$ 금속간화합물이 생성되었다. 고속 전단 시험의 경우, 전단속도가 증가함에 따라 취성 파괴율이 증가하였다.

• 한국기계가공학회지
• /
• 제14권6호
• /
• pp.57-62
• /
• 2015

A large variety of pipe flanges are required in the marine and construction industry. Pipe flanges are usually welded or screwed to the pipe end and are connected with bolts. This approach is very simple and has been widely used for a long time; however, it results in high development costs and low productivity, and the products made through this approach usually have safety problems in the welding area. In this research, a new approach for forming pipe flanges based on cold forging and the floating die concept is presented. This innovative approach increases the effectiveness of the material usage and saves time and costs compared with the conventional welding method. To ensure the dimensional accuracy of the final product, finite element analysis (FEA) was carried out to simulate the process of cold forging, and orthogonal experiment methods were used to investigate the influence of four manufacturing factors (stroke of distance, pin die angle, forming of pipe diameter, and speed of the die) and predict the best combination of them. The manufacturing factors were obtained through numerical and experimental studies, which show that the approach is very useful and effective for the forming of pipe flanges and could be widely used in the future.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.54-61
• /
• 2015

In this study, effect of laser power on hardness and microstructure of SKD61 Hot Die steel of which surface was melted and hardened with Yb:YAG disk laser was investigated. Beam speed was fixed at 70 mm/sec and distance between them was 0.8 mm about Laser surface melting. The only thing that was changed laser power. Laser powers were 2.0, 2.4 and 2.8 kW. No defect was found under all conditions. As the laser power increased, the penetration depth were deepened and the bead width was also widened. There was no hardness deviation of fusion zone at same laser power and it was higher than that of heat affected zone. In addition, the more laser power increased, the more hardness in fusion zone decreased. Fusion zone was macroscopically dendrite structure. However, core matric in dendrite was lath martensite of 100 nm size. There were $M_{23}C_6$ of 500 nm and the VC and $Mo_2C$ of a nano meters on boundary of dendrite.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.107-115
• /
• 1999

The objective of this research was to study the formation of the thick hardened layer with the addition of metal powder(Cu) and ceramics powders(TiC) on the aluminum 5083 alloys by plasma transferred arc process(PTA process) and to characterize the effect of overlaying conditions on the overlaid layer formation. This was followed by investigating the microstructures of the overlaid layers and mechanical properties such as hardness and wear resistance. The overlaid layer containing copper powder was alloyed and intermetallic compound($CuAl_2$) was formed. The overlaid layers with high melting point TiC powders, however, did not react with base metal. Wear resistance of the alloyed layer was remarkably improved by the formation of $CuAl_2$, precipitate phase, which prevented wear of base aluminum alloys and at higher wear speed, accelerated sliding of the counter part. Wear resistance of the composite layer was also remarkably improved because TiC powder act as a load barring element and Fe debris fragments detached from the counter part act as a solid lubricant on the contact surface.

• 대한금속재료학회지
• /
• 제47권7호
• /
• pp.447-453
• /
• 2009

Isotropic conductive adhesives (ICAs) have been used or considered as an interconnect material for radio frequency identification (RFID) inlays or other flip chip assemblies due to the advantages of having a low temperature and high-speed bonding. In this work, the curing properties of commercial ICAs for the RFID tag application and the signal transmission in conductive lines that contained the ICA joints were evaluated as a function of the degree of cure at 900 MHz frequency range. The ICAs showed adequate signal transmission only after the curing process passed over the critical time. It was also found that the insertion loss of signal was more dependent on the contact states of Ag fillers in the bondline in preference to the electrical resistance of the ICA itself.