• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1837-1839
• /
• 2003

Recently deep interests have been paid on the effective generation of ozone, which has been widely used for water treatment, deoderization, color removal and chemical processing of exhausted smoke. The silent discharge reaction has been proposed as the most effective in the many ozone generation methods by electric discharge, because silent discharge excel others in the condition of high ozone generation yield and low power consumption. In this paper, ozone water generated system measure with silent discharge characteristics and pulsed power supply.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.271-278
• /
• 2011

This paper presents a LLC resonant controller IC for secondary side control without external active devices to achieve low profile and low cost LED back light units. A gate driving transformer is adopted to isolate the primary side and the secondary side instead of an opto-coupler. A new integrated dimming circuitry is proposed to improve the dynamic current control characteristic and the current density of a LED for the brightness modulation of a large screen LCD. A dual-slope clock generator is proposed to overcome the frequency error due to the under shoot in conventional approaches. This chip is fabricated using 0.35 ${\mu}m$ BCD technology and the die size is $2{\times}2\;mm^2$. The frequency range of the clock generator is from 50 kHz to 500 kHz and the range of the dead time is from 50 ns to 2.2 ${\mu}s$. The efficiency of the LED driving circuit is 97 % and the current consumption is 40 mA for a 100 kHz operation frequency from a 15 V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.8
• /
• pp.1606-1612
• /
• 2015

In this paper, a portable high efficiency nondispersive infrared(NDIR) $CO_2$ sensor module with a smart device interface is developed. For low power consumption design, an IR LED was used instead of tungsten lamp for light source and an optical waveguide optimized to the sensor module is designed. With the smart device interface, power of the sensor module is applied from the battery of smart phone. The measured data of the sensor module such as $CO_2$ concentration, temperature, and humidity are displayed on the smart phone using android application. From measured results, the developed sensor module shows ${\pm}60ppm$ tolerance error from 0 to 3,000ppm $CO_2$ concentration range among $-10^{\circ}C$ and $50^{\circ}C$ ranges.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.3
• /
• pp.558-566
• /
• 2015

LED, the next-generation light source, rapidly develops and has advantages of low power, high efficiency, and long life. Accordingly, an interest in lightings by using LED rises. If emotional lighting is implemented by using LED, all colors can be represented by using 3 primary colors of light, differently from the conventional single-color lighting. LED emotional lightings which can control human emotions continue to be developed thanks to these advantages. This study was conducted to design an algorithm for expressing LED emotional lighting in line with the situation and temperature by extracting colors for concentration and resting situations in indoor environment and mixing them with colors of the temperature felt by user. The LED emotional lighting designed with a neuro-fuzzy system was found to have effects on user's emotions during concentration and resting.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.1
• /
• pp.34-40
• /
• 2012

In this paper, voltage clamped tapped-inductor boost converter with high voltage conversion ratio is proposed. The conventional tapped-inductor boost converter has a serious drawback such as high voltage stresses across all power semiconductors due to the high resonant voltage caused by the leakage inductor of tapped inductor. Therefore, the dissipative snubber is essential for absorbing this resonant voltage, which could degrade the overall power conversion efficiency. To overcome these drawbacks, the proposed converter employs a voltage clamping capacitor instead of the dissipative snubber. Therefore, the voltage stresses of all power semiconductors are not only clamped as the output voltage but the power conversion efficiency can also be considerably improved. Moreover, since the energy stored in the clamp capacitor is transferred to the output side together with the input energy, the proposed converter can achieve the higher voltage conversion ratio than the conventional tapped-inductor boost converter. Therefore, the proposed converter is expected to be well suited to various applications demanding the high efficiency and high voltage conversion ratio. To confirm the validity of the proposed circuit, the theoretical analysis and experimental results of the proposed converter are presented.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.4
• /
• pp.511-519
• /
• 2014

This study is aimed to analyze the three-dimensional underwater irradiance using an optical simulation software and to clarify the propriety and operation method under considering luminous intensity distribution of the luring lamp and penetrability in the seawater, when we use the light diffuser type 300W high powered LED and the metal halide lamp (MHL) on a coastal squid jigging vessel in the 10-ton class, simultaneously. For their attenuation characteristics of each wavelength in relation to the sea, LED lamp was to be effective in the 1.9-fold at 50 m depth and 2.1-fold at 80 m for underwater irradiance more than MHL according to the power consumption. In addition, the underwater irradiance distribution using the LED and MHL combination was rather increased even when reducing total power usage up to 20% depending on the simulation with changing the configuration and lighting angle of the lamp. These results can be utilized as an evaluation method of the operation and performance of the LED lamp according to adjusting its arrangement and lighting angle.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.168.2-168.2
• /
• 2014

반사방지막 코팅(Anti-reflection coating)은 태양전지(Solar cell), 발광다이오드(LED) 등의 반사율을 낮추어 효율을 증대시키기 위하여 사용되고 있다. 본 실험에서는 유리 기판 위에 실리콘 타겟을 이용한 반응성 high power impulse magnetron sputtering (HIPIMS) 장비를 활용하여, 높은 공정 압력(High-pressure)에서 펄스폭(Pulse width)을 조절하여 $SiO_2$ 반사방지막 코팅층을 형성하였다. 또한, 기공이 더 많은 박막을 제작하기 위해 빗각증착(Oblique-angle deposition)을 적용하여 더 좋은 광학 특성을 갖는 반사방지막 코팅층을 형성하였다. UV-Vis spectrometer를 이용하여, 380~800 nm 파장에서 투과율(Transmittance)을 측정하여 비교, 분석하였다. Ellipsometer를 이용하여 $SiO_2$ 박막층의 굴절률(Refractive index)을 측정한 결과, 반사방지막 코팅층 내부 기공에 따라 다양한 굴절률을 가지는 것을 확인할 수 있었다. 또한, 코팅층 내부 기공의 형상을 확인하기 위해 SEM(Secondary electron microscopy)을 활용하여 코팅층 단면(Cross section)을 측정하였다. 이를 활용하여 낮은 굴절률을 갖는 반사방지용 $SiO_2$ 코팅층을 형성하여 태양전지의 광 변환 효율을 상승 시킬 수 있고, 발광다이오드의 광 추출 효율을 증가시킬 있을 것으로 여겨진다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.169-180
• /
• 2018

White light-emitting diodes (LEDs) are more economical than fluorescent lights, and provide high brightness, a high lifetime expectancy, and greater durability. As LEDs are closely connected with people's daily lives, dimming control of LED is an important component in providing energy savings and improving quality of life. In visible light communications systems using these LEDs, multiple input multiple output (MIMO) technology has attracted a lot of attention, in that it can attain the channel capacity in proportion to the number of antennas. This paper analyzes the power performance of three kinds of modulation in visible light communications (VLC) systems applied space-time block code (STBC) techniques. The modulation schemes are return-to-zero on-off keying (RZ-OOK), variable pulse position modulation (VPPM), and overlapping pulse position modulation (OPPM), and dimming control was applied. The power requirements and power consumption were used as metrics to compare the power efficiency in $2{\times}2$ STBC-VLC environments under the three kinds of modulation. We confirm that dimming control affects the communications performance of each modulation scheme. VPPM showed greater consumption among the three modulations, and OPPM showed energy savings comparable to VPPM.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.91-101
• /
• 2017

In this study, we conducted the preliminary research for high speed laser cutting of LED module. In particular, the feasibility of ultra-high speed laser cutting of 100 mm/s which exceeds the cutting speed of conventional dicing saw was examined. For this, copper/ceramic and silicone/ceramic hybrid substrates, which are the components of the LED module, were fabricated, and the surface morphology, surface roughness and flexural strength of the laser-cut samples were investigate and compared with the dicing-cut samples. To investigate optimal laser cutting conditions for hybrid substrates, the effects of various laser cutting conditions on cutting surface characteristics were studied using single ceramic and copper substrate. Optimal laser cutting conditions of the hybrid substrates were the use of Ar assist gas, high laser power and high assist gas pressure. Comparing the cutting surface of the hybrid substrates, the surface characteristics of the laser-cut samples are slightly inferior to those of the dicing-cut samples. The average surface roughness of the laser-cut samples was about $9{\mu}m$, and that of the dicing-cut samples was about $4{\mu}m$. However, considering very low cutting speed (3 mm/s) of the dicing saw, the surface morphology of the laser-cut sample was relatively uniform, and the surface roughness was not much different from that of the dicing-cut sample. The flexural strength of the laser-cut samples was equivalent to or slightly inferior to the flexural strength of dicing-cut samples. However, if the laser processing conditions are sufficiently optimized, the ultra-high speed laser cutting of the LED module will be possible.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.104-110
• /
• 2015

LED has added value as a lighting source in the illuminating industry because of its high efficiency and low power consumption. In LED production processes, the chip cutting process, which mainly uses a scribing process with a laser has an effect on quality and productivity of LED. This scribing process causes problems like heat deformation, decreasing strength. The inner laser method, which makes a void in wafer and induces self-cracking, can overcome these problems. In this paper, cutting sapphire wafer for fabricating LED chip using the inner laser scribing process is proposed and evaluated. The aim is to settle basic experiment conditions, determine parameters of cutting, and analyze the characteristics of cutting by means of experimentation.