• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.5
• /
• pp.25-34
• /
• 1997

Relatively slow tuning speed of optical device causes the unwanted delay in high speed single-hop multiwavelength networks. To lessen the overhead, we present a channel access protocol with dynamjic message scheduling. Th eframe structure of proposed protocol adopts hybrid multiaccess scheme in which WDMA is used as a basic multiaccess technique and TDMA is used to provide subchannels within a wavelength band. This architecture has two merits : the network extention is not limited by available number of wavelengths, and the transmission delay caused by optical device tuning time can to minimize the number of tunings. It schedules messages that require same wavelength channels sequencely, so the total transmission delay is reduced by decreasement of wavelength changes. The performance of proposed protocol is evaluated through numerical analysis based on probability and queueing theory. The peformance of proposed protocol is evaluated through numerical analysis based on probability and queueing theory. The numeric results show that the peformance of proposed protocol is better than that of previous one.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.470-473
• /
• 2007

Geothermal heat exchanger(GHEX) is a major component of Geothermal heat pump system(GSHPs). In Common, We use the vertical type GHEX in Korea. But vertical type GHEX needs a high cost for installation, because of drilling the hole which has 200m depth at max. So, We suggest the use of horizontal type GHEX. When we construct buildins, We excavate the ground and we can install the horizontal type GHEX at the excavated underground. It's very cheap and convenient method compare to vertical type GHEX installation. This study is peformed to estimate the peformance of horizontal type GHEX and to analyze effects of heat exchanger types and undergroundwater. As the result, slinky type GHEX has a 66% efficiency compare to vertical type GHEX and mat type has a 201% efficiency at the undergroundwater zone.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.5
• /
• pp.365-376
• /
• 2002

An experimental study has been conducted to measure the local film-cooling effectiveness and the heat transfer coefficient for a single row of rectangular-shaped holes. four different cooling hole shapes such ai a straight rectangular hole, a rectangular hole with laterally expanded exit, a circular hole and a two-dimensional slot are tested. A technique using thermochromic liquid crystals determine adiabatic film cooling effectiveness values and heat transfer coefficients on the test surface. Both film cooling effectiveness and heat transfer coefficient are measured for various blowing rates and compared with the results of the cylindrical ho1es and the two-dimensional slot. The flow patterns downstream of holes are calculated numerically using a cummercial package. The results show that the rectangular hopes provide better peformance than the cylindrical holes. For the rectangular holes with expanded exit, the penetration is reduced significantly, and the higher and more uniform cooling Peformance is obtained even at relatively high blowing rates.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.36-41
• /
• 1995

Recently, as the problems according to the deteriorated structure were gathering sterength, there were required the advent of the high peformance for polymer ceme at compostie in building constrution devision. The polymer cement mortar was developed for improvements of the various problems in ordinary cement mortar. finishing method using the super flowing polymer-based self levelling mortar for concrete slab and floor.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.9
• /
• pp.28-35
• /
• 1997

A novel high-Q vertical jinductor for MMICs is proposed and characterized in a wide range of frequencies (DC~10 GHz) using the numerical methods such as the PeEC(partial equivalent element circuit), the FDM (finite difference method) and the MoM (method of moments). Electrical superiority of the vertical inductor to the horizontal is observed in terms of the magnetic flux linkage and the ground screening effect. The veritcal bondwire inductor is designed in consideration of the wire bonding feasibility and the optimum electrical peformance. This structure is also analyzed using the equivalent circuit and compared with the conventional spiral inductors From the calculated results, high Q-factor, inductance, and cut-off frequency are observed to be inherent characteristics of the veritcal bondwire inductor.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.5A
• /
• pp.521-526
• /
• 2004

OFDM is a very attractive technique for achieving high-bit-rate data transmission and high spectrum efficiency. However, one of disadvantages of OFDM signal is the high PAPR characteristic when multi-carriers are added up coherently. In this Paper, we propose-scrambling scheme using correlator for PAPR reduction and reducing the amount of PAPR calculations. The simulation results show that this scheme has less computational complexity and reasonable PAPR reduction capability compared to PTS technique.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.5
• /
• pp.5-14
• /
• 2003

Tracking control schemes on the precise mechanical system in presence of nonlinear dynamic friction is proposed. A nonlinear dynamic friction is regarded as the bristle friction model to compensate fer effects of friction. The conventional SMC method often shows poor tracking performance in high-precision position tracking application since it cannot completely compensate for the friction effect below a certain precision level. Thus to improve the precise position tracking performance, we propose the SMC method combined with the disturbance observer having tunable transient performance. Then this control scheme has the high precise tracking peformance as well as a good transient response when it is compared with the conventional SMC method and the similar types of observers, The experiment on the XY ball-screw drive system with the nonlinear dynamic friction confirms the feasibility of the proposed control scheme.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 2006.04a
• /
• pp.80-85
• /
• 2006

HSS (high strength steel) is widely applied to reduce the weight but improve the strength in automobiles. This research has been peformed to secure a methodology to accurately predict the springback of HSS for successful tool and process designs in sheet stamping operations. We first peformed U-draw bending test to evaluate the springback characteristic. We then evaluated forming and springback processes using the 1-row model of the finite element method. Based on the peformance measure and parameters selected, extensive analyses of the factor effects on the springback have been made using experimental design concepts. We specifically selected Taguchi's orthogonal array, $L_{18}(2^1{\times}3^7)$, and the optimal level combination of the factors have been drawn from the analysis.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.44-49
• /
• 2000

Recently, PM-high speed steel(PM-HSS) has reportedly been a good alternative material for rolling mill because of its superior peformance to conventional HSS. This paper has been aimed to investigate the possibility for application to rolling contact element for PM-HSS by X-ray diffraction technique. The X-ray elastic constant for PM-HSS has been found by X-ray diffraction during the four-point bending test. Residual stress and half-value breadth on the contact surface during rolling contact fatigue process by X-ray diffraction have also been measured. The result of this study shows that the application of X-ray diffraction technique to PM-HSS could be as possible alternative material as conventional HSS. Half-value breadth on rolling contact surface by X-ray diffraction is not changed during rolling contact fatigue process. On the other hand, the residual stress is changed. This suggests that dislocation reaction has been hardly occurred in rolling contact, depending on supersaturated carbon in PM-HSS.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.5
• /
• pp.367-376
• /
• 1987

In this paper we have disigned and implemented a real time ALE (adaptive line enhancer) using a high speed digital processor,NEC 7720. For the ALE system, we have employed an adaptive LMS(least mean square) algorithm proposed by Widrow and Hoff and a 32-order FIR(finite impulse response) filter. Extensive computer simulations have been performed to investigate the peformance of the ALE and to determine necessary parameters for hardware design. The developed software for an NEC 7720 was tested in real time operation using an NEC7720 hardware emulator. The ALE has been tested by sinusoidal waves and real CW (continuous wave) signals. It was found that the experimental results were well agreed with the computer simulation results. Thus it can be concluded that the ALE is useful for detection and enhancement of a sinusoidal signal which is corrupted by an additive Gaussian noise.