• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.37-38
• /
• 2010

For MHz-class high frequency inverter in wireless power transfer applications, the voltage/current surges can be occurred in power stage when driving on the inverter. And also, the high-frequency oscillations can be produced at a high switching frequency due to the parasitic elements. The voltage and current stresses of the switching devices lead to the switching losses. The efficiency of the high frequency inverter will be reduced. And the inverter circuit with the sudden voltage and current fluctuations also generates the noise such as the EMI. Zero voltage, zero current switching technique can be used to reduce the switching loss and the noise. The high power density and high efficiency can be obtained. In this paper, the high-frequency inverter for short-range wireless power transfer applications was discussed. The feasible inverter circuit is analyzed in the circuit operating characteristics and the results are verified by the simulation.

• Communications for Statistical Applications and Methods
• /
• v.23 no.5
• /
• pp.411-421
• /
• 2016

Large frequency limiting distributions of two errors in realized covariance are investigated under noisy and non-synchronous high frequency sampling situations. The first distribution characterizes increased variance of the realized covariance due to noise for large frequency and the second distribution characterizes decreased variance of the realized covariance due to discretization for large frequency. The distribution of the combined error enables us to determine the sampling frequency which depends on a nuisance parameter. A consistent estimator of the nuisance parameter is proposed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.992-995
• /
• 2006

In this Paper the noise characteristics of KTX are analyzed in order to study the interior noise mechanism of KTX in slab tracks, which has become an issue since the commercial operating in 2004. The analysis of the interior noise of KTX in tunnel with concrete track shows sharply increased noise level in the range of 80Hz that is the natural frequency of the KIX carbody. The frequency characteristics of noise and acceleration levels of KTX in tunnels are compared to understand the interrelation between the noise inside the vehicle and outside the vehicle in the slat track tunnel. As a noise abatement method, the mud-flap was modified with intend to reduce the noise outside gangway and the interior noise inside the passenger compartment ultimately. The effect of this mud-flap modification on the interior noise is introduced and discussed.

• Journal of the Korean Society for Railway
• /
• v.12 no.4
• /
• pp.465-471
• /
• 2009

In this paper, a relationship between the noise and vibration of a high-speed train's wheelset is examined by using time-varying frequency analysis with random data analysis which together contributes to a reduction in the number of experimental running. The noise and vibration of the wheelset is mainly caused by an interaction between the wheel and railway which shows in non-stationary characteristics. For the analysis, they are measured by some microphones and accelerometers, and those signals are post-processed by time-varying frequency analysis with random data analysis. From the analysis, their methods are useful for analyzing the noise and vibration of high-speed train's wheelset.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1735-1740
• /
• 2000

The aim of this study is to analyze the sound insulation performance of windows depending on the sound source types and to propose the noise control method in the apartment house. The regions where apartment houses are constructed are varied in the dominant noise sources such as aircraft noise, railway noise and road traffic noise. For the experiment, nine noise sources including pink noise were selected and recorded, which was used in the experiment by reproducing. As a result of this study, the sound insulation performance of window was found that when the frequency contents of the noise were high level in all frequency bands the difference of sound insulation performance was negligible, but when the frequency contents were low level at particular frequency band the difference of sound insulation performance was shown very differently.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.5
• /
• pp.431-437
• /
• 2013

Measured acoustic signal from operating high speed train contains frequency change called doppler shift due to its motion. To avoid this doppler shift wind tunnel test is required. But scaledown of model can cause change of source characteristics. And measurements using some part of train cannot reproduce real flow condition. The best way to recognize real noise source characteristics is measurement from operating high speed train but doppler shift makes it hard. So, we developed simple dedopplerization technique for one microphone and applied to field test data of high speed train. Through this, we could capture real frequency of noise from operating high speed train.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1285-1289
• /
• 2006

In a large diameter piping system, high frequency energy can produce excessive noise, high vibration, and failures of thermo-well, instrumentation, and attached small-bore piping. High frequency energy is generated by flow induced vibration like vortex shedding in orifices and valves. Once this energy is generated, amplification may occur from acoustical and/or structural resonances, resulting in high amplitude vibration and noise. At low frequencies, pipe vibration occurs laterally along the pipe's length, but at higher frequencies, the pipe shell wall vibrates radially across its cross-section. The simple beam analogy which is based on the beam mode vibration can not be applied to evaluate shell mode vibration. ASME OM3 recommends that the stress be measured directly by strain gauge and be evaluated according to the fatigue curves of the piping material. This Paper discusses the excitation and amplification mechanism relevant to high frequency energy generation in piping system, the monitoring method of the shell mode vibration in ASME OM3, the evaluation method generally used in the industry. Finally this paper presents the stress evaluation of the cavitating venturi down stream piping, where high frequency shell mode vibrations were observed during the operation.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.4
• /
• pp.242-247
• /
• 2018

The automotive industry is making various efforts to cope with ever-increasing exhaust emissions and fuel economy regulations. However, this often results in degraded NVH (Noise, Vibration, and Harshness) performance. For example, we proposed the causes and improvements for the noise generated by the high-pressure pump noise of a gasoline engine, the change of acceleration noise due to dual injection of MPI (Multi-Point Injection) and GDI (Gasoline Direct Injection), the noise of a gasoline turbocharger, and the combustion noise deteriorated due to the injection parameters calibration in a diesel engine. Since these noises are caused by the high frequency noise, and the driver feels the rough sound quality, efforts to reduce them with proper NVH measures are indispensable.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.319-322
• /
• 1998

A 20 GHz 2-stage MMIC (Monolithic Microwave Integrated Circuits) LNA(Low Noise Amplifiers) has been designed. The pHEMT with gate length of 1.15 um has been used to provide ultra low noise and high gain amplification. Series and Shunt feedback circuits were interted to ensured high stability over frequency range of DC to 60 GHz. The size of designed MMIC LNA is 2285um x 2000um(4.57mm2). The simulated noise figure of MMIC LNA is less than 1.7 dB over frequency range of 20 GHz to 21 GHz.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1187-1190
• /
• 2009

CURVE SQUEAL NOISE IS THE INTENSE HIGH FREQUENCY TONAL THAT CAN OCCUR WHEN A RAILWAY VEHICLE TRAVERSES A CURVE OR A SWITCH. THE HIGH NOISE LEVEL CAUSES ANNOYANCE FOR PEOPLE WHO LIVE IN THE NEIGHBOURHOOD OF THE SQUEALING RAILWAY TRACK AS WELL AS FOR THE PASSENGERS IN CARS WITH CURVES. THIS PAPER EXAMINES THE SPECTRAL SOUND DISTRIBUTION IN CURVES FOR KTX TRAIN. THE FREQUENCY RANGE IS FROM AROUND 4,000 TO ALMOST 16,000Hz, WITH NOISE LEVELS UP TO 92dB IN CURVE R400.