• 한국건축시공학회지
• /
• 제7권1호
• /
• pp.71-77
• /
• 2007

This paper is to investigate the effect of the curing temperature on strength development of concrete incorporating cement kiln dust(CKD) and blast furnace slag (BS) quantitatively. Estimation of the compressive strength of the concrete was conducted using the equivalent age equation and the rate constant model proposed by Carino. Correction of Carino model was studied to secure the accuracy of strength development estimation by introducing correction factors regarding rate constant and age. An increasing curing temperature results in an increase in strength at early age, but with the elapse of age, strength development at high curing temperature decreases compared with that at low curing temperature. Especially, the use of BS has a remarkable strength development at early age and even at later age, high strength is maintained due to accelerated pozzolanic activity resulting from high temperature. Whereas, at low curing temperature, the use of BS leads to a decrease in compressive strength. Accordingly, much attention should be paid to prevent strength loss at low temperature. Based on the strength development estimation using equivalent age equation, good agreements between measured strength and calculated strength are obtained.

• Geomechanics and Engineering
• /
• 제35권1호
• /
• pp.95-108
• /
• 2023

Soft soil ground is a crucial factor limiting the development of the construction of transportation infrastructure in coastal areas. Soft soil is characterized by low strength, low permeability and high compressibility. However, the ordinary treatment method uses Portland cement to solidify the soft soil, which has low early strength and requires a long curing time. Microbially induced carbonate precipitation (MICP) is an emerging method to address geo-environmental problems associated with geotechnical materials. In this study, a method of bio-cementitious mortars consisting of MICP and cement was proposed to stabilize the soft soil. A series of laboratory tests were conducted on MICP-treated and cement-MICP-treated (C-MICP-treated) soft soils to improve mechanical properties. Microscale observations were also undertaken to reveal the underlying mechanism of cement-soil treated by MICP. The results showed that cohesion and internal friction angles of MICP-treated soft soil were greater than those of remolded soft soil. The UCS, elastic modulus and toughness of C-MICP-treated soft soil with high moisture content (50%, 60%, 70%, 80%) were improved compared to traditional cement-soil. A remarkable difference was observed that the MICP process mainly played a role in the early curing stage (i.e., within 14 days) while cement hydration continued during the whole process. Micro-characterization revealed that the calcium carbonate filling the pores enhanced the soft soil.

• Computers and Concrete
• /
• 제17권2호
• /
• pp.271-280
• /
• 2016

This study examined the mechanical properties and adiabatic temperature rise of low-heat concrete developed based on ternary blended cement using ASTM type IV (LHC) cement, ground fly ash (GFA) and limestone powder (LSP). To enhance reactivity of fly ash, especially at an early age, the grassy membrane was scratched through the additional vibrator milling process. The targeted 28-day strength of concrete was selected to be 42 MPa for application to high-strength mass concrete including nuclear plant structures. The concrete mixes prepared were cured under the isothermal conditions of $5^{\circ}C$, $20^{\circ}C$, and $40^{\circ}C$. Most concrete specimens gained a relatively high strength exceeding 10 MPa at an early age, achieving the targeted 28-day strength. All concrete specimens had higher moduli of elasticity and rupture than the predictions using ACI 318-11 equations, regardless of the curing temperature. The peak temperature rise and the ascending rate of the adiabatic temperature curve measured from the prepared concrete mixes were lower by 12% and 32%, respectively, in average than those of the control specimen made using 80% ordinary Portland cement and 20% conventional fly ash.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.75-78
• /
• 2005

This raper investigates the effect of curing temperature on strength development of concrete incorporating cement kiln dust(CKD) and blast furnace slag (BS) quantitatively. Estimation of compressive strength of concrete was conducted using equivalent age equation and rate constant model. An increasing curing temperature results in an increase in strength at early age, but with the elapse of age, strength development at high curing temperature decreases compared with that at low curing temperature. Especially, the use of 35 has a remarkable strength development at early age and even at later age, high strength is maintained due to accelerated pozzolanic activity resulting from high temperature. Whereas, at low curing temperature, the use of BS leads to a decrease in compressive strength. Accordingly, much attention should be paid to prevent strength loss at low temperature. Based on the strength development estimation using equivalent age equation, good agreements between measured strength and calculated strength are obtained.

• 한국농공학회지
• /
• 제13권4호
• /
• pp.2419-2425
• /
• 1971

한중(寒中)콘크리트 시공(施工)에 염화(鹽化)칼슘사용(使用)은 콘크리트의 초기강도(初期强度)를 최대한(最大限)으로 높여 동해(凍害)를 방지(防止)함과 경제적(經濟的인 구조물(構造物)을 만들고자 하는데 목적(目的)이 있으며 시험결과(試驗結果)로서 그의 범위(範圍)를 요약(要約)하면 다음과 같다. 1. 염화(鹽化)칼슘을 시멘트중량비(重量比) 1.5%를 TYPE I TYPE II에 혼합(混合)하면 초기강도(初期强度)를 최대한(最大限)으로 증진(增進)할 수 있고 구조물(構造物)의 안전(安全)을 위(爲)해서 1.5%내외(內外)가 적합(適合)하겠다. 2. 염화(鹽化)칼슘을 혼합(混合)하여 동결(凍結)의 위험(危險)을 방지(防止)하기 위한 콘크리트를 만들자면 w/c비(比)를 50% 내외(內外)로 정(定)해야 만이 한중(寒中)에 안전(安全)하겠다. 3. 포조란 초기강도(初期强度)는 떨어지나 후기강도(後期强度)가 점차(漸次)로 상승(上昇)한다. 4. 콘크리트의 초기강도(初期强度)의 증진(增進)으로 양생기간(養生期間)을 최대한(最大限)으로 단축(短縮)시킬 수 있으므로 콘크리트 구조물(構造物)의 끝손질을 조기(早期)에 실시(實施)해야 한다. 염화(鹽化)칼슘의 혼입(混入)은 시멘트응결(凝結)을 촉진(促進)시킬 수 있어 한중(寒中)에 있어서 동해(凍害)를 방지(防止)하고 공기(工期)를 최대한(最大限)으로 단축(短縮)시킬 목적(目的)으로 공사시공(工事施工) 현장(現場)에서는 유효히 사용(使用)될것으로 사료(思料)된다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2001년도 학술논문발표회
• /
• pp.82-87
• /
• 2001

The purpose of this study is for the active use of the fly ash, which is a by-product of the combustion pulverizes coal thermal power plants, to compensate for the lack of landfill and for conservation of energy, by using fly ash as the supplementary cementitious material, and to prove its possibility as the related products of the cement. First of all, the ordinary fly ash is grinded in a special method and its fineness is controlled from 6000$\textrm{cm}^2$/g to 8000$\textrm{cm}^2$/g, then replaced it with the 10% to 80% of the cement mortar in order to test physics characteristics. The first experiment conducts on the strength development in fly ash replacing content and fineness. and the changes of the flow values, incorporating fly ash into cement. The second one is about the slow development of the strength of the fly ash mortar in early ages, and improves its strength with the activator $Na_{2}SO_{4}$, using high volume fly ash.

• 한국건축시공학회지
• /
• 제6권3호
• /
• pp.99-105
• /
• 2006

In this paper, the estimation of compressive strength of concrete incorporating fly ash subjected to high temperature is discussed. Ordinary Portland cement and fly ash cement(30% of fly ash) were used, respectively. Water to binder ration ranging from 30% to 60% and curing temperature ranging from $20^{\circ}C{\sim}65^{\circ}C$ were also adopted for the experimental parameters. According to results, at the high temperature, FAC had higher strength development at early age than OPC concrete and it kept its high strength development at later age due to accelerated pozzolanic reaction subjected to high temperature. For strength estimation, Logistic model based on maturity equation and Carino model based on equivalent age were applied to verify the availability of estimation model. It shows that fair agreements between calculated values and measured values were obtained evaluating compressive strength with logistic curve. The application of logistic model at high temperature had remarkable deviations in the same maturity. Whereas, the application of Carino model showed good agreements between calculated values and measured ones regardless of type of cement and W/B. However, some correction factors should be considered to enhance the accuracy of strength estimation of concrete.

• 한국환경과학회지
• /
• 제16권3호
• /
• pp.347-355
• /
• 2007

In this paper, estimation of the compressive strength of the concrete incorporating blast furnace slag subjected to high temperature was discussed. Ordinary Portland cement and blast furnace slag cement (BSC;30% of blast furnace slag) were used, respectively. Water to binder ratio ranging from 30% to 60% and curing temperature ranging from $20^{\circ}C{\sim}65^{\circ}C$ were also chosen for the experimental parameters, respectively. At the high temperature, BSC had higher strength development at early age than OPC concrete and it kept its high strength development at later age due to accelerated latent hydration reaction subjected to high temperature. For the strength estimation, the Logistic model based on maturity equation and the Carino model based on equivalent age were applied to verify the availability of estimation model. It was found that fair agreements between calculated values and measured values were obtained evaluating compressive strength with logistic curve. The application of logistic model at high temperature had remarkable deviations in the same maturity. Whereas, the application of Carino model showed good agreements between calculated values and measured ones regardless of type of cement and W/B. However, some correction factors should be considered to enhance the accuracy of strength estimation of concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.45-48
• /
• 2005

This study is basic experiment for estimating influence of strength by curing temperature of concrete's heat of hydration and estimate relationship of compressive strength development by initial curing temperature factor, and then asume temperature factor which influence compressive strength development and for showing basic document of qualify control. According to the result of cement mortar by the curing temperature factor high-curing temperature shows high strength on 3 day compare with low curing-temperature, shows higher strength than the piece of high curing temperature.

• 콘크리트학회논문집
• /
• 제13권2호
• /
• pp.139-145
• /
• 2001

보통강도의 한중콘크리트에 있어서 동해는 일반적으로 콘크리트의 공기량 및 양생방법 등에 의해 억제시킬 수 있는 것으로 알려져 있으며, 고강도콘크리트는 낮은 물결합재비로 인하여 동결융해저항성이 우수한 것으로 알려져 있지만, 한중콘크리트 타설 및 초기양생에 있어서 발생될 수 있는 초기동해에 관한 연구는 아직 미흡한 실정이다. 따라서 본 연구에서는 동절기에 고강도콘크리트를 타설할 경우 초기동해에 의해 발생되는 인장응력의 영향을 고려하여 인장강도비를 검토하고, 초기동해를 입은 경우 장기재령에 의한 강도회복성을 검토하여 동절기 고강도콘크리트의 현장적용을 위한 기초적 자료로서 제시하고자 한다. 본 연구의 결과 초기동해를 입은 고강도콘크리트의 내동해성은 동해를 받은 시점이 빠를수록 공기량이 적을수록 저하하는 것으로 나타났으며, 내동해성을 확보하기 위해서는 공기량 4% 이상을 확보해야 할 것으로 사료되며, 동해를 받은 후 양생에 의한 압축강도의 회복성능은 W/C가 낮을수록 초기동해를 받기 전 양생기간이 증가할수록 향상되는 것으로 나타났다. 또한 향 후 고강도콘크리트의 동절기 시공에 있어서 초기동해에 대한 내동해성을 지니기 위해서는 인장강도 5kgf/$\textrm{cm}^2$ 이상을 확보해 야 할 것으로 사료된다.