• 대한기계학회논문집A
• /
• 제20권4호
• /
• pp.2752-2759
• /
• 1996

This paper presents crack growth analysis approach on the basis of neural networks, a branch of cognitive science to high temperature low cycle fatigue that shows strong nonlinearity in material behavior. As the number of data patterns on crack growth increase, pattern classification occurs well and two point representation scheme with gradient of crack growth curve simulates crack growth rate better than one point representation scheme. Optimal number of learning data exists and excessive number of learning data increases estimated mean error with remarkable learning time J-da/dt relation predicted by neural networks shows that test condition with unlearned data is simulated well within estimated mean error(5%).

• 대한기계학회논문집A
• /
• 제25권5호
• /
• pp.772-778
• /
• 2001

In this study, corrosion fatigue characteristics of 12Cr alloy steel were investigated in 3.5wt.% NaCl solution of 150$^{\circ}C$ and 4.5bar. Behavior of corrosion fatigue cracks was measured by the indirect compliance method and compared with the results in distilled water and in air. 1) 12Cr alloy steel was susceptible to temperature. Its susceptibility was increased as the temperature was increased. 2) The crack growth characteristics of 12Cr alloy steel in distilled water were similar to 3.5wt.% NaCl solution. 3) The temperature of solution affects to the crack growth characteristics of 12Cr alloy steel. In corrosion solutions of 4.5bar, 150$^{\circ}C$, fracture surfaces of corrosion fatigue crack growth at a/W=0.3 was showed the trans-granular fracture suface. As the crack grew up, it was changed to inter-granular type. In condition of high temperature, The crack growth behaviors of 12Cr alloy steel were remarkable.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1453-1460
• /
• 2002

Creep-fatigue crack growth models have been proposed employing $(C_t)_{avg}$ as a crack tip parameter characterizing the time-dependent crack growth. The basic assumptions made in these previous models were ideal creep reversal conditions such as no creep reversal and complete creep reversal condition. Due to this assumption, the applicability of the models was limited since they did not consider partial creep reversal condition which is usually observed in many engineering metals at high temperature. In this paper the creep reversal parameter, Temperature;$C_R$, which was defined by Grover, is critically evaluated to quantity the extent of partial creep reversal at the crack tip. This approach does not rely on any simplifying assumptions regarding the extent of the amount of creep reversal during the unloading part of a trapezoidal fatigue cycles. It is shown that the $(C_t)_{avg}$ value calculated for 9Cr steel agrees well with the experimentally measured one. It is argued that the extent of improvement is not significant when the result is compared with that of the conventional model which has an assumption of full creep reversal behavior.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.156-162
• /
• 2000

Sensitized STS 304 stainless steel crack growth rate(CGR) in high temperature water was investigated under trapezoidal wave loading test using fracture mechanics techniques. The CGR, due to stress corrosion cracking(SCC), were systematically measured as a function of the stress intensity factor and stress. holding time under trapezoidal wave loading. In high temperature water, CGR was enhanced by a synergistic effects in combination with an aggressive environment and mechanical damage. The CGR, $(da/dN)_{env}$ was basically described as a summation of the environmentally assisted crack growth rate $(da/dN)_{SCC}$, $(da/dN)_{CF}$ and fatigue crack growth rate in air $(da/dN)air,. The CGR, $(da/dN)_{env}$, increased linearly with increasing stress holding time. The CGR, $(da/dN)_{SCC}$ decreased linearly with increasing stress holding time. Fracture surface mode varied from trans-granular cracking to inter-granular cracking with increasing stress holding time.

• 한국기계가공학회지
• /
• 제6권3호
• /
• pp.92-97
• /
• 2007

The overlay welding the automobile where the durability is demanded, it is used in the vessel engine valve, plant valve and pump parts. Cause of damage public opinion one what is thought is the fatigue load due to the opening and shutting operation right time repetition of the engine valve. The damage cause of the engine valve or explanation of destruction mechanism is very difficult. The research which it sees to make clear a overlay welding of Co-alloy by Plasma Transferred Arc Weld Surfacing Process reconsideration fatigue crack initiation and fatigue crack growth mechanism at high temperature.

• 한국추진공학회지
• /
• 제20권2호
• /
• pp.11-17
• /
• 2016

분말야금 니켈기 초내열합금은 항공기 터빈 엔진의 고온용 부품으로 사용되고 있다. 본 연구에서는 상온, $600^{\circ}C$ 및 $700^{\circ}C$에서 CT시편을 이용하여 피로균열진전거동이 평가되었다. ASTM E647에서 제시한 직류전위차법이 피로균열진전 동안에 균열 길이를 측정하기 위하여 사용되었다. 응력비 0.5에서 피로균열진전속도는 응력비 0.1에서와 비교하여 더 빠르게 나타났다. 피로균열진전속도는 응력비와 온도의 증가와 함께 증가하였다. 파단면 관찰은 파괴메커니즘 분석을 위해 수행하였다.

• 한국세라믹학회지
• /
• 제36권1호
• /
• pp.15-20
• /
• 1999

상압소결 질화규소에 대한 고온정피로 거동을 K-t(stress intensity/life test)법에 의해 조사하였다. 정피로 크랙성장속도는 온도의 증가와 함께 증가한다. 온도의 증가에 따라 크랙성장속도가 증가하는 이유는 온도 증가에 따라 파괴인성치가 감소하기 때문으로 판명되었다. 즉 정피로 크랙성장속도 da/dt를 da/dt=AK1m로 나타내면, 이 식의 정수 A는 파괴인성치의 파괴인성치의 함수이도, 지수 m은 온도나 파괴인성치에 관계없이 일정한 상수이다. 그러나 글래스상의 연화가 일어나는 고온의 경우 크랙성장속도는 이상의 관계로부터 벗어남을 발견하고, 그 이유에 대하여 고찰하였다.

• 한국주조공학회지
• /
• 제11권3호
• /
• pp.217-227
• /
• 1991

The present study was conducted to estimate the fatigue crack growth rate of the Mo-Ni alloyed ductile cast iron for the influence of austempering temperature and time. The fatigue crack growth rate was affected by retained austenite. Retained austenite volume were higher with the ductile cast irons which were austempered at $360^{\circ}C$ than austempered at $260^{\circ}C$, and the fatigue crack growth rate of the former was lower than that of the latter. Also, the fatigue growth rate of the former was the lowest at austempering for 1 hour and that of the latter was the lowest at austempering for 3 hours.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.308-313
• /
• 2004

Recently, the steel parts used for automobiles and trains are required to be used under higher stress than ever before in need of the weight down. In this study, high strength and superior toughness spring steels as the suspension material, used for automobile and railroad industries were utilized to carry out the following in vestigations; 1) To evaluate the characteristics of fatigue crack propagation, the experiments of fatigue crack growth were respectively carried out at the room temperature(RT), $100^{\circ}C$, $200^{\circ}C$ 2) Peening and unpeening materials at the each temperature were investigated for the effect on fracture toughness by compressive residual stress generated from the shot peeing.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.104-107
• /
• 2001

Creep-fatigue crack growth behavior at the heat affected zone of 1Cr-0.5Mo steel weldment has been experimentally studied. Load hold times of the tests for trapezoidal fatigue wave-shapes were varied among 0, 30, 300 and 3,600 seconds. Time-dependent crack growth rates were characterized by the $C_{t}$ estimated with the equation proposed by the previous finite element analysis work. It was concluded that the $C_{t}$ values calculated from the properties of parent metal were quite comparable to the accurate $C_{t}$ values calculated from both of weld and parent metals.etals.