• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.4
• /
• pp.641-650
• /
• 2017

In order to include the design capability for a compound rotorcraft in a helicopter conceptual design and optimization framework, relevant further improvement was planned and conducted. Previously, a certain conceptual design optimization framework was developed by the present authors to design a modern rotorcraft with single main and tail rotor. The previously developed framework was further improved to expand its capability for a compound rotorcraft. Specifically, its power estimation algorithm was upgraded by using a comprehensive rotorcraft analysis program, CAMRAD II. The presently improved conceptual design and optimization framework was validated using data of the XH-59A aircraft.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1385-1389
• /
• 2005

This paper describes the design, analysis and manufacture procedure of the composite blade for hingeless rotor system of unmanned helicopters. Helicopter rotor system is the key structural unit that produces thrust and control forces for intended flight conditions. In this work, a hingeless rotor system is adopted, and base on the design requirements for rotor system, composite blade section design and calculation of material properties were performed. In order to avoid the unstable state such as resonance, vibration characteristics of rotor system were analyzed. Finally, this paper describes the forming and manufacture of composite blade.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.1-7
• /
• 2002

This paper describes the analysis method about the dynamic characteristics and vibratory load through HDS(Helicopter Design Study). To analyze the dynamic characteristics of helicopter rotor blade, the natural frequencies and modes are calculated according to rotor operational speed(Ω). Generally the proximity of rotor natural frequency and N times of rotor operational speed is a dominant component to determine the helicopter vibration. Also we can predict the airframe vibration by calculating the airload of rotating blade exactly. We expect to establish the design procedure of rotor dynamics by describing the two major analysis methods necessary to rotor design.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.1
• /
• pp.74-85
• /
• 1990

The LQG and LQG/LTR compensators have the same structrues in dynamics. The only difference is the values of the design parameters in the two compensators. The design parameters of the LQG and LQG/LTR compensators are selected in the sense of the least-squares error minimi- zation and loop shaping, respectively. In this paper, the LQG and LQG/ LTR design methods are applied to the helicopter in hover which is modeled as a SISO fourth order system. The dynamic characteristics and the perfor- mance of the two control systems are analyzed by the computer simulation. It is found that the LQG/LTR design method is systematic and has good performance in comparision with the LQG design method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.612-619
• /
• 2010

In this paper, an elastomeric bearing for a helicopter rotor hub is designed using nonlinear finite element method. The elastomeric bearing is the main component of the helicopter rotor hub that acts as a hinge to three motions(flapping, lagging and pitching) of rotor blade. The elastomeric bearing consists of rubber and metal plates. The stiffness design of the elastomeric bearing is important because elastic deformation of rubber is served to hinge. Accordingly, the elastomeric bearing is designed to satisfy the stiffness requirements for rotor hub bearing. In this study, a FE model generation algorithm is developed and stiffness characteristic of a rubber plate is analyzed for an efficient design of the spherical elastomeric bearing. It is proven that the elastomeric bearing satisfies stiffness requirements of the spherical bearing for a helicopter rotor hub.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.5
• /
• pp.411-422
• /
• 2014

A helideck is a very valuable offshore structure for the take-off and landing of a helicopter. In order to design a helideck, the design parameters and various loads defined by the regulations related to the design of a helideck should be applied. In this study, a risk analysis was performed based on the helicopter accidents for seven years, and the frequency and possible reasons for accidents involving helidecks were investigated. In addition, a finite element analysis of a steel helideck mounted on the upper deck of a ship (shuttle tanker) was performed with the load that should be considered when designing a helideck. Based on the results, a parametric study of helideck was carried out by applying a variety of design parameters, and an improved helideck design was presented. This improved helideck reduced the steel used by up to 24% compared to the initial helideck design, and the results of a finite element analysis were analyzed and compared with those of the initial analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.159-164
• /
• 2016

This paper reports the load factor logic design for a fly-by-wire helicopter flight envelope protection. As a helicopter is very complex system with a rotor, fuselage, engine, etc., there are many constraints on the flight region. Because of these constraints, pilots should consider them carefully and have a heavy workload, which causes controllability degradation. In this respect, automatic logic is needed to free the pilot from these considerations. As one of these logics, the flight envelope protection logic for the load factor of a FBW helicopter was designed. The flight to exceed the load factor is caused by an abrupt pitch cyclic stick change. In this scheme, the load factor limit logic was added between the pilot stick command block and pitch attitude command block. From the current load value, the available attitude range was calculated dynamically and simulated on the helicopter simulator model to verify the performance. A comparison of the simulation results at the hovering and forward speed region with and without applying the load limiting logic showed that the load factor limit was exceeded more than 20% when the logic was not applied, whereas with the load factor limit logic the load factor was within the limit. In conclusion, a dynamically allocated limitation logic to helicopter FBW controller was verified by simulation.

• Journal of computational fluids engineering
• /
• v.11 no.3 s.34
• /
• pp.1-7
• /
• 2006

Euler and Navier-Stokes flow analyses for helicopter rotor in hover were performed as low and high fidelity analysis models respectively for the future multidisciplinary design optimization(MDO). These design-oriented analyses possess several attributes such as variable complexity, sensitivity-computation capability and modularity which analysis models involved in MDO are recommended to provide with. To realize PC-based analyses for both fidelity models, reduction of flow domain was made by appling farfield boundary condition based on 3-dimensional point sink with simple momentum theory and also periodic boundary condition in the azimuthal direction. Correlations of thrust, torque and their sensitivities between low and high complexity models were tried to evaluate the applicability of these analysis models in MDO process. It was found that the low-fidelity Euler analysis model predicted inaccurate sensitivity derivatives at relatively high angle of attack.

• Journal of the Korean Society of Systems Engineering
• /
• v.1 no.2
• /
• pp.56-62
• /
• 2005

In this study, we first define user requirements to fulfill the reconnaissance and the search missions, by analyzing the system characteristics and operation environment. By investigating the design technology level, the development and procurement costs, the strong system design concepts and possible alternatives will be proposed. To analyze the system requirements, the Quality Function Deployment of the systems engineering approach will be implemented. The promising design alternatives that satisfy the user requirements are extracted by constructing the Morphological Matrix, then the best design concept will be obtained using the Pugh Concept Selection Matrix and the TOPSIS(Technique of Order Preference by Similarity to Ideal Solution).

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.2
• /
• pp.203-210
• /
• 2010

For the development of a better product which fits to the target user population, physical workloads such as reach and visibility are evaluated using digital human simulation in the early stage of product development; however, ergonomic workload assessment mainly relies on visual observation of reach envelopes and view cones generated in a 3D graphic environment. The present study developed a quantitative assessment method of physical workload in a digital environment and applied to the evaluation of a Korean utility helicopter (KUH) cockpit design. The proposed assessment method quantified physical workloads for the target user population by applying a 3-step process and identified design features requiring improvement based on the quantified workload evaluation. The scores of physical workloads were quantified in terms of posture, reach, visibility, and clearance, and 5-point scales were defined for the evaluation measures by referring to existing studies. The postures of digital humanoids for a given task were estimated to have the minimal score of postural workload by finding all feasible postures that satisfy task constraints such as a contact between the tip of the index finger and a target point. The proposed assessment method was applied to evaluate the KUH cockpit design in the preliminary design stage and identified design features requiring improvement. The proposed assessment method can be utilized to ergonomic evaluation of product designs using digital human simulation.