• Agricultural and Biosystems Engineering
• /
• 제6권1호
• /
• pp.22-26
• /
• 2005

A wind-heat generation system was developed and the system consisted of an electric motor, a heat generation drum, a heat exchanger, two circulation pumps and a water storage tank. The heat generation drum is an essential element determining performance of the system. Frictional heat was generated by rotation of a rotor in the drum filled with a working fluid, and the heat stored in the fluid was used to increase water temperature through the heat exchanger. Effects of some factors such as rotor shape, kind and amount of working fluid, rotor rpm and water flow rate in the heat exchanger, affecting the system performance were investigated. Amounts of heat generated were varied, ranging from 126,000 to 32,760 kJ/hr, depending on combination of the factors. Statistical analysis using GLM procedure revealed that the most influential factor to decide the system performance was amount of the fluid in the drum. Experiments showed that the faster the speed of the rotor, the greater heat was obtained. The greatest efficiency of the heat generation system, electric power consumption rate vs gained heat amount of water, was about 70%. Though the heat amount was not enough for plant bed heating of a 0.1-ha greenhouse, the system would be promising if some supplementary heat source such as air- water heat pump is added.

• 천문학회보
• /
• 제36권2호
• /
• pp.88.1-88.1
• /
• 2011

Shocks are thought to be important in the dynamics and heating of the solar chromosphere. The observational determination of shock parameters, however, has been hardly done because of the difficulty of observation at a high spatial, temporal and spectral resolution, and the lack of an effective method of inferring physical parameters from spectral data. Our inversion of the spectral data of the $H{\alpha}$ and Ca II 854.2 nm lines simultaneously taken from an intranetwork area, produced temporal profiles of temperature as well as line-of-sight velocities, from which we infer that three-minute chromospheric oscillations prevailing in the upper chromosphere are in fact trains of strong shocks with a strength of about two and a propagation speed of 20 km s-1 that carry a mechanical energy flux of 500 W m-2 upward. Our result supports the notion that shocks dominate the heating of the upper chromosphere, and probably the corona as well, at least in intranetwork regions of the quiet sun.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.953-958
• /
• 2006

Perimeter zone has been reinforced by active systems, such as fan-coil units, because it causes an increase in heating and cooling loads, dew condensation in winter, or discomfort with cold-draft to residents in buildings, through poor insulation by light-weighed skin due to progressing multi-storied buildings and skyscrapers. However, because these active systems raise Its capacity so that fossil fuel is used as much as they are added, and ultimately, greenhouse effect is urged, we proposed BIPV system functioned as solar collector which can substitute active system. As an early stage, heat balance equation in steady-state by Fortran was used not only for pre-heating effect and electric power capacity during the day in winter, but also for electric power capacity during day in slimmer and sky radiation effect during night in summer. Especially, we should have considered shading on PV, since even a little bit of it makes the efficiency too low for the PV to work. Still, when the flux of pre-heated air was increased to make air-barrier, its temperature was not enough to make it because the speed of heat exchange was too fast to warm up the air, thus the capacity to meet the condition was evaluated, and electric power from PV was made used for it.

• 한국기계가공학회지
• /
• 제19권10호
• /
• pp.44-51
• /
• 2020

We studied the heating characteristics of a whirling spindle. This spindle is an important component of a whirling machine for turning a ball screw shaft. In the manufacturing process for a conventional ball screw shaft, a single tool is used to form a spiral in a lathe machine tool. Thereafter, a high-frequency heat treatment process is performed. Recently, a whirling-type cutting method has emerged. This method can perform hard turning in the rotating direction of the spiral portion of the ball screw shaft by rotating and mounting multiple tools. The whirling method can be applied to the heat-treated material. In this study, an experimental apparatus was constructed to analyze the whirling spindle. The experiment proceeded in four steps. The rotating speed of the whirling spindle was set to ISO random and sequential rising conditions. Cooling and non-cooling modes in the cooling jacket were tested. As a result of the above experiment, the heating characteristics of the whirling spindle were derived.

• 열처리공학회지
• /
• 제36권4호
• /
• pp.206-214
• /
• 2023

Tungsten carbide has many industrial applications due to its high electrical and thermal conductivity, high melting temperature, high hardness and good chemical stability. Because tungsten carbide is difficult to sinter, it is sintered with nickel or cobalt as a binder and is currently used in nozzles, cutting tools, and molds. Alumina is reported to be a viable binder for tungsten carbide due to its higher oxidation resistance and lower cost than nickel and cobalt. The ultrafine tungsten carbide-graphene-alumina composites were rapidly sintered in a high frequency induction heating active sintering unit. The microstructure and mechanical properties (fracture toughness and hardness) of the composites were investigated and analyzed by Vickers hardness tester and electron microscope. Since the high-frequency induction heating sintering method enables high-speed sintering, ultrafine composites can be prepared by preventing grain growth. In the tungsten carbide-graphene-alumina composites, the grain size of tungsten carbide increased with the amount of alumina participation. The hardness and fracture toughness of the tungsten carbide-5% graphene- x% alumina (x = 0, 5, 10,15) composites were 5.1, 8.6, 8.6, and 8.4 MPa-m^1/2 and 2384, 2168, 2165, and 2102 kg/mm², respectively. The fracture toughness increased without a significant decrease in hardness. Sinterability was improved by adding alumina to tungsten carbide-graphene.

• ETRI Journal
• /
• 제26권6호
• /
• pp.575-582
• /
• 2004

Fully-depleted silicon-on-insulator (FD-SOI) devices with a 15 nm SOI layer thickness and 60 nm gate lengths for analog applications have been investigated. The Si selective epitaxial growth (SEG) process was well optimized. Both the single- raised (SR) and double-raised (DR) source/drain (S/D) processes have been studied to reduce parasitic series resistance and improve device performance. For the DR S/D process, the saturation currents of both NMOS and PMOS are improved by 8 and 18%, respectively, compared with the SR S/D process. The self-heating effect is evaluated for both body contact and body floating SOI devices. The body contact transistor shows a reduced self-heating ratio, compared with the body floating transistor. The static noise margin of an SOI device with a $1.1\;{\mu}m^2$ 6T-SRAM cell is 190 mV, and the ring oscillator speed is improved by 25 % compared with bulk devices. The DR S/D process shows a higher open loop voltage gain than the SR S/D process. A 15 nm ultra-thin body (UTB) SOI device with a DR S/D process shows the same level of noise characteristics at both the body contact and body floating transistors. Also, we observed that noise characteristics of a 15 nm UTB SOI device are comparable to those of bulk Si devices.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2008년도 추계학술논문발표회 논문집
• /
• pp.479-483
• /
• 2008

There are no International Standards or Criteria pertaining to fires inside tunnels at the moment, but there are some fire-related regulations in some advanced countries such as Germany and the Netherlands where some fire-related studies have been expedited. Germany has established regulations related to the safety of structures by stipulating Fire Curves of RABT and EBA Tunnels. Also, the Netherlands has established the resistance capacity of structures by stipulating RWS curve so that they can prevent the adjacent area from being damaged due to a tunnel collapse. Hydrocarbon Fire Curve is the standard assessing the behaviour of a structure in a serious fire, by increasing the heating speed and the maximum temperature of ISO 834 Curve, while MHC Fire Curve, which was established in France, realizes more serious fire conditions. In this study, we aimed to develop the basis of full-sized experiments, with which you can assess the fire-resisting capacity against the fire strength of concrete PC panel lining, through the realization of various tunnel fire curves as mentioned above, by developing the heating furnace suitable for the requirements of Fire-Resisting Standards, with which you can assess the fire damage of tunnel concrete lining. We have developed various conditions of the heating furnace and the method to install a thermo couple within the furnace based on EFNARC and KS F2257-1. We have also conducted a calibrating experiment in order to secure its reliability.

• 대한토목학회논문집
• /
• 제37권2호
• /
• pp.507-512
• /
• 2017

유인 행성 탐사를 위해 인류는 행성에서 반영구적으로 거주할 수 있는 기술을 개발하고 있으며, 이에 거주에 기본적인 3대 요소인 의식주(衣食住)는 건설 분야의 필수적인 기술의 뒷받침이 요구된다. 국제적으로 인프라 구축 기술을 개발하기 위해 현지 시멘트화, 황, 알루미늄 등의 다양한 재료와 방법으로 시도되고 있다. 본 연구에서는 폴리머를 이용한 건설 인프라 재료 기술을 개발하기 위해 유인 탐사에 요구되는 조건에 부합하는 폴리머 콘크리트 시공성 검증 기술을 제안하고자 한다. 하부에서 가열하는 방식으로 제작된 중량비 10%의 폴리머를 사용한 콘크리트 시험체는 가열 후 2시간이 지났을 때 안정화 되었으며, 상부 가열 방식에 비해 강도는 낮았지만 고착속도가 2배 빠른 것으로 나타났다. 이러한 결과는 향후 유인 탐사를 위한 달 시설물 의 건설에 적용할 수 있을 뿐만 아니라 먼지방지를 위한 도로나 제방과 같은 인프라 시설의 시공성 향상에도 활용 가능하다고 기대된다.

• 터널과지하공간
• /
• 제5권1호
• /
• pp.22-40
• /
• 1995

Thermomechanical characteristics of rocks such as thermal shock, thermal expansion, thermal cracking were experimentally investigaed using Iksan granite, Cheonan tonalite and Chung-ju dolomite to obtain the basic data for proper design and Chung-ju dolomite to obtain the basic data for proper design and stability analysis of underground structures subjected to temperature changes. The effect of thermal shock did not appear when the heating speed was under 3$^{\circ}C$/min. and there existed little difference between multi-staged cyclic heating and single-cycled heating. Thermal expansion of rocks was affected by mineral composition, crack porosity and the degree of thermal craking. In quartz-beraring multimineralic rocks such as Iksan granite and Cheonan tonalite, the thermal expansion coefficient increaseed continuously with temperature rise, but that of Chung-ju dolomite which was a monomineralic rock showed a constant value for the temperature above 250$^{\circ}C$, Chung-ju dolomite yielded the lowest critical threshold temperature(Tc) of 100$^{\circ}C$ and unstable thermal cracking was initiated above the new threshold temperature(Tc')of 300$^{\circ}C$. Above Tc' thermal cracks grew but they were not interconnected. Iksan granite showed closing of microcracks to the temperature of 100$^{\circ}C$, then expanded linearly to Tc of 200$^{\circ}C$. Above Tc, thermal cracking was initiated and progressed rapidly and almost all the grain boundaries were cracked at 600$^{\circ}C$. Cheonan tonalite also showed similar behavior to iksan granite except that Tc was 350$^{\circ}C$ and that thermal cracks propagated more rapidly. Thermal expansions calculated by Turner's equation were found to be valid in predicting the thermal expansion and cracking behavior of rocks.

• 한국항공우주학회지
• /
• 제43권1호
• /
• pp.33-39
• /
• 2015

본 논문은 램프의 수명저하 없이 $1,000^{\circ}C$이상의 초고온 급속가열 환경을 지속적으로 모사할 수 있고 기존 사용해온 열하중 부가장치 대비 내구성과 신뢰성이 향상된 열하중 부가장치를 개발하여 초고속 비행체 날개의 구조 건전성 평가에 적용, 그 활용가능성을 수록한 내용이다. 본 시험을 통하여 초고온의 운용환경에 노출되는 비행체 날개의 공력가열에 의한 강성저하를 정량적으로 예측할 수 있었으며, 향후 비약적인 증가추세에 있는 공력가열온도를 경험하게 되는 극초음속 비행체에 대한 고온환경에서의 구조 강도특성 평가가 가능해짐으로써 시험 신뢰성 향상과 함께 고온구조강도시험 수행능력을 한 단계 도약시킬 수 있는 계기가 되었다.