• Journal of the Korean Wood Science and Technology
• /
• 제23권4호
• /
• pp.33-38
• /
• 1995

The rates of fixation of CCA-Type B and CCFZ in blocks of radiata pine sapwood were compared at various temperatures and conditioning methods (drying and nondrying conditioning). Also the time required to proper fixation of preservative components in the treated wood was estimated. Fixation was monitored by the rates of depletion of free hexavalent chromium in the cell lumens in the teated blocks. The rate of preservative fixation in wood was highly temperature dependent. The fixation rate was considerably accelerated by means of heating and complete fixation of hexavalent chromium was achieved within about 12 hours by heating at $60^{\circ}C$. The moisture content of treated wood during fixation apparently played an important role in the fixation process. The fixation rate of treated wood conditioned in nondrying conditions was much more faster than that of treated wood conditioned in drying conditions. particularly when the moisture content of treated wood was below fiber saturation point. Time required to full fixation could be predicted successfully using the fixation temperatures applied since the correlation between the fixation temperature and the fixation time was excellent. regardless of conditioning methods.

• 센서학회지
• /
• 제25권1호
• /
• pp.8-12
• /
• 2016

A planar, light-weight, and low-cost notch filter structure is required for the KSTAR ECEI (Electron Cyclotron Emission Imaging) system to protect the mixer arrays from spurious plasma heating power. Without protection, this heating power can significantly degrade or damage the performance of the mixer array. To protect mixer arrays, a frequency selective surface (FSS) structure is the suitable choice as a notch filter to reject the spurious heating power. The FSS notch filter should be located between the lenses of the ECEI system. This paper presents a 170 GHz FSS notch filter for the KSTAR ECEI sensor application. The design of such an FSS notch filter is based on the single-sided square loop geometry, because that makes it relatively insensitive to the incident angle of incoming wave. The FSS notch filter exhibits high notch rejection with low pass-band insertion loss over a wide range of incident angles. This paper also reviews the simulated and measured results. The proposed FSS notch filter might be implemented in other millimeter-wave plasma devices.

• 한국세라믹학회지
• /
• 제33권12호
• /
• pp.1353-1364
• /
• 1996

Recently semiconductor doped glasses have attracted attention as nonlinear optical materials because of their large third order nonlinear optical properties. The transparent and homogeneous CdS-doped SiO2 glass thin films were obtained by the dip=coating process of the sol-gel method. Thin films were consisted of glasses containing CdS microcrystallites which were formed by dissolved Cd2+ and S2- ions in a SiO2 matrix solutions. A subsequent thermal treatment of this samples led the formation of colloidal agglomerates and finally of microcrystallites. The size of CdS microcrystallites was about 4 to 15 nm after thermal treatments at various heating conditions. From the optical absorption spectra of the CdS-doped SiO2 glass films it was found that the absorption edge was blue-shifted compared with that of the bulk CdS crystal(~2, 4 eV) and that the amount of energy shift was inversely proportional to the crystal size. And the band gap energy increased with the decrease in crystallite size indicating that the quantum size effects occured.

• 대한의용생체공학회:의공학회지
• /
• 제12권4호
• /
• pp.255-260
• /
• 1991

A system using a personal computer has been developed for Polymerase Chain Reaction, an amplifying process of specific DNA. This system is composed of software and hardware which contains a control system, a heating and cooling system, a multichannel A/D converter, and a personal computor. The software is programmed'in assembly'and basic language. The newly developed PCR system which is controlled by the program of the personnal computor can be applied 1.o the amplification of various DNA. This system was tested by using Mycobacterium tuberculosis DNA and showed the DNA band on the UV transilluminator.

• 한국산업융합학회 논문집
• /
• 제8권1호
• /
• pp.47-55
• /
• 2005

Infrared heating has been traditionally used in industrial applications for processes such as dehydration of food industrial. This heating method involves the application of radiation in the wavelength range of 2 to 50 micrometers. In this work, simultaneous heat balance equations were developed to simulate the infrared radiation heating of agricultural products. The equations assume that moisture diffuses to the outer boundaries of the material in liquid form and evaporation occurs at the surface of the agricultural products. Energy for moisture evaporation is supplied by the infrared radiant energy. The optimum temperature and drying time for the best drying conditions of changing the red peppers with the moisture content of 18% and the restore rate of 80~85% are $80^{\circ}C$ and 44 hours. The performance of radiation tubes coating with the radiation paint developed in this research has the energy of $2.27{\times}103W/m^2{\mu}m$, $150^{\circ}C$ within the scope of radiation wave length of $2{\sim}30{\mu}m$ and has the radiation 0.92~0.93, which is superior to the general radiation tubes. The extinction coefficient according to the band pass filter using the 4 flux theory ha higher dependability on wave length, accounting for $2{\sim}17{\mu}m$ and $5{\times}105{\sim}106m-1$. A comparison between the theoretical energy transfer whose figures are interpreted according to 4 flux theory and the experimental energy transfer of far infrared dryer leads to the findings of the agreement less than 5%.

• 한국ITS학회 논문지
• /
• 제10권1호
• /
• pp.42-48
• /
• 2011

본 논문에서는 GaN HEMT (Gallium Nitride High Electron Mobility Transistor) bare-chip을 이용하여 X-대역에서 수동로드 풀(Passive load-pull)을 수행하였다. 열로 인한 특성 변화가 최소화 된 동작 조건을 얻기 위해 드레인 바이어스 전압과 입력 RF 신호를 펄스로 인가하였다. 전자기장 시뮬레이션과 회로 시뮬레이션을 병행하여, 와이어 본딩 효과를 고려하여 드레인 경계면에서의 정확한 임피던스 정합 회로를 구현하였다. 임피던스를 변화시키기 위해 마이크로스트립 라인 스터브의 길이가 조절 가능한 회로를 설계하였다. 펄스 로드 풀 실험 결과 8.5 GHz에서 9.2 GHz 대역에서 최대 42.46 dBm의 출력 전력을 얻었으며, 58.7%의 드레인 효율 특성을 얻었다.

• 한국어병학회지
• /
• 제10권1호
• /
• pp.31-38
• /
• 1997

잉어로부터 분리한 Aeromonas hydrophila는 세포 밖으로 여러 종류의 proteases를 생산한다. A. hydrophila의 배양 상층액을 이용한 inhibitor assay를 통하여, 주된 활성을 나타내는 metallopretease와 약한 활성을 나타내는 serine protease가 있음을 알게 되었다. Gelatin SDS-PAGE를 통하여 두 개의 활성 band가 관찰되었으며, 이 들 중 넓게 퍼진 band는 metalloprotease에 특이하게 작용하는 inhibitor인 EDTA에 의해 활성이 상실되었고 따라서 metalloprotease임을 알 수 있었다. 다른 하나는 serine protease에 특이하게 반응하는 inhibitor인 PMSF에 의해 저해되어 serine protease임을 알 수 있었다. 이러한 두 extracellular protease의 활성은 $75^{\circ}C$에서 30 분간 열을 가한 후에도 Gelatin SDS-PAGE상에 남아있었다. 그런데, 주된 metalloprotease는 Sephadex G-75를 이용한 column chromatography를 거친 후 Gelatin Gel상에서 두 개의 band로 분리되었다.

• 한국식품과학회지
• /
• 제20권1호
• /
• pp.34-39
• /
• 1988

여러가지 육가공품(肉加工品)중 특정 단백질 원료의 첨가여부를 판정하여 변조식품(變造食品)을 검출하는 한 방법으로서, 각종 육류단백질, non-meat protein, 어육(魚肉)가공품을 대상으로 disc SDS-Poly acrylamide gel electrophoresis의 사용 가능성을 실험하였다. Total protein fraction에 대한 전기영동 결과 복잡하고 많은 band를 보여 각 시료에 고유한 특성을 찾아보기 어려웠다. Low salt-soluble protein fraction에서는 total protein fraction 에서 보다 band 수가 상당히 감소함을 보였고 각 단백질 원료에 대하여 보다 고유한 band pattern을 나타내었다. Acetone-insoluble protein fraction 에서는 non-meat protein의 경우 육류단백질과 상당히 다른 경향을 나타내었고. 소세지 원료의 가열처리에 의하여 단백질의 band수와 양이 감소하였다. 따라서 적당한 단백질 추출조건(抽出條件)을 설정하여 전기영동을 실시하면, 특정(特定) 단백질을 첨가한 변조식품의 검출이 가능해질 것으로 생각된다.

• Journal of the Korean Wood Science and Technology
• /
• 제42권3호
• /
• pp.339-345
• /
• 2014

집성재의 생산성 향상을 위한 고주파 가열 경화기술에 대해 연구하였다. 고주파가 유전체에 가해지면 내부에서 에너지 손실에 의한 발열이 발생한다. 집성재를 구성하는 라미나와 접착제는 유전체이므로 집성재에 고주파를 주사하면 내부에서 발열이 발생한다. 집성재 제조에 이용되는 대부분의 상온 경화형 접착제는 고온에서 빠른 경화가 이루어지므로 고주파 가열 기술을 이용하면 집성재 내부 접착층의 온도를 상승시킴으로써 빠른 경화를 유도할 수 있다. 본 연구에서는 낙엽송재와 phenol-resorcinol-formaldehyde (PRF) 접착제의 유전 특성을 평가하고, 집성재 내부의 접착층의 빠른 경화를 유도하는 고주파 가열 경화 기작을 이론적으로 분석하였다. 연구 결과, 온도상승인자인 PRF 접착제의 상대손실계수가 낙엽송재의 상대손실계수에 비해 높았으나, 온도상승저해인자인 밀도와 비열도 높았다. 그러나 상대손실계수의 비율이 온도상승저해인자의 비율보다 높기 때문에 고주파 가열에 의한 발열량은 접착제에서 더 높을 것으로 예상된다. 이러한 실험 결과를 이용한 이론적 접근을 바탕으로, 접착층이 목표온도까지 상승하기 위한 ISM 영역의 고주파 주파수 별 전기장의 상대 세기를 추정하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.142-147
• /
• 2009

COMS (Communication, Ocean and Meteorological Satellite) is a geostationary satellite and has been developing by KARI for communication, ocean and meteorological observations. It will be tested under vacuum condition and very low temperature in order to verify thermal design of COMS. The test will be performed by using KARI large thermal vacuum chamber, which was developed by KARI, and the COMS will be the first flight satellite tested in this chamber. The purposes of thermal balance test are to correlate analytical model used for design evaluation and predicting temperatures, and to verify and adjust thermal control concept. KARI has plan to use heating plates to simulate space hot condition especially for radiator panels such as north and south panels. They will be controlled from 90K to 273K by circulating GN2 and LN2 alternatively according to the test phases, while the shroud of the vacuum chamber will be under constant temperature, 90K, during all thermal balance test. This paper presents thermal modelling including test chamber, heating plates and the satellite without solar array wing and Ka-band reflectors and discusses temperature prediction during thermal balance test.