• 농업과학연구
• /
• 제10권1호
• /
• pp.156-165
• /
• 1983

태양열(太陽熱)을 이용(利用)한 silica gel의 활용(活用)에 대(對)한 기초자료(基礎資料)를 얻고자, silica gel을 이용(利用)한 양파의 건조특성(乾燥特性)과, 공기(空氣)의 제습효과(除濕效果)를 구명(究明)하고, 건조제(乾燥劑)로서의 재사용(再使用)을 위(爲)하여 실험(實驗)한바, 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 외기온도(外氣溫度) $30^{\circ}C$, 상대습도(相對濕度) 55% 내외(內外)에서 포화(飽和)silica gel을 수분함량(水分含量) 8%까지 재생(再生)시키는데 14시간(時間) 소요(所要)되었다. 2. 집열기(集熱器)를 재순환(再循環)시켜 건조(乾燥)한 결과(結果), 노천건조(露天乾燥)보다 1/2정도(程度) 시간(時間)이 단축(短縮)되었다. 3. 실험기간중(實驗期間中) 집열기(集熱器)의 평균효율(平均效率)은 25%였다. 4. 건조실(乾燥室)을 이용(利用)한 송풍건조시(送風乾燥時), 갈변도(褐變度)가 1/2로 감소(減少)되었다.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.70-75
• /
• 2010

Compressed air represents an energy source and an force-transmission medium for brake systems on medium-heavy and heavy-duty commercial vehicles. However, one disadvantage is the tendency of air to absorb moisture in the form of water vapor. This water vapor condenses once the air, which is heated during compression, cools back to ambient temperature upon emerging from the air compressor. The resulting condensation assumes the form of moisture in pneumatic lines, air tanks, cylinders and valve assemblies and can have negative consequences for the brake system and vehicle safety. The pneumatic systems on today's vehicles are equipped with air dryers, in which the supplied air is dried according to the adsorption principle. In the systems, the compressed air flows through a granular desiccant with molecular sieves which captures the water molecules.

• 설비공학논문집
• /
• 제18권1호
• /
• pp.7-16
• /
• 2006

Both the computational and experimental analysis have been conducted in this study to develop the high efficiency agriculture products dryer by the uniform thermal flow distribution in the drying room. It has been developed based on the results of the computation and experiment in the conventional dryer to improve the thermal flow distribution in drying room. The developed dryer can be prevented the local concentration of the heated wind and achieved the uniform flow distribution using the installation of vertical branch ducts, ribs, guide vanes and porous plates. As a result, the developed dryer reduced the fuel consumption up to $15\%$ and the electricity consumption up to $31.5\%$ compared with the conventional dryer.

• 한국의류산업학회지
• /
• 제11권6호
• /
• pp.961-967
• /
• 2009

In order to examine the availability of heat treatment for color developing in persimmon dyeing, the rayon fabrics dyed with persimmon extract from unripe persimmon which was used after stock and fermentation. Dyed fabrics were heated at various temperature and time by contacting press heat and drying heat. Color developing results were influenced by the difference of heating method. Press heating method is more available than drying heat method. Effect of temperature and time on ${\Delta}Ea^*b^*$ and color values of dyed rayon fabrics was considerable. Considering the practical aspect, The temperature around $140{\sim}160^{\circ}C$ and the time no longer 40 minutes can be reach the region of the full color developing by press heating process. It was very shortened than any other method(drying air heat, xenon radiation, sunlight). The dyed rayon fabrics with heat treatment have darker and deeper red-yellow color than which by sunlight and xenon radiation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.278-284
• /
• 2000

The method of Impinging jet was applied lots of part in industrial field as a cooling of as gas turbine blade, a annealing of metal and plastic sheets, drying of textile, veneer paper, X-ray medical devices, laser weapons and electronic components. This study's main factor is reciprocating Jet impingement perpendicular to the heated Surface. We researched the effect of heat transfer and enhancement with pulsating air jet. The pulsating air jet has an improvement in pulsating Frequencies((f= 0.5, 1, 1.5, 3Hz) and nozzle-to-plate distances($l/d=\;2{\sim}4,\;6{\sim}8,\;4{\sim}6,\;8{\sim}10$).

• 동력기계공학회지
• /
• 제10권2호
• /
• pp.54-61
• /
• 2006

In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Generally, the drying method is various as to the property of material and use. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heating using hot air between sludge particles and heated gas. In this paper, we performed a numerical analysis of the inner air flow of the ANDRICH type dryer through the changing rotational speed from 3rpm to 10rpm. A PIV can be applied to research a inner flow of ANDRICH type dryer.

• Journal of Biosystems Engineering
• /
• 제2권2호
• /
• pp.37-45
• /
• 1977

Solar energy is a potential source of power that offers much promise being used for low-temperature applications like drying farm crops, space heating, and water heating for domestic uses. Already much of it are being used for those purpose in foreign countries. However, very little research has been done to determine the possibility of using the solar energy in Korea. This study was conducted to develop the general prediction equation of the total radiation on a horizontal surface in Daejeon area based on 5 years 91972, Jun.1-1976. Dec.31) meteorological data (bright sunshine hours, average total horizontal radiation), and to obtain experimentally the thermal efficiency of solar air and water collectors, which will be used as a basic data of designing flat-plate solar collector system.In addition to the thermal efficiency of the collectorsthe relationship among those factors affecting it such as weather condition, orientation factor, and tilted angle of collector was analyzed. The results of this study were as follows. 1. The general predicted equation of the total radiation on a horizontal surface in Daejeon area based on bright sunshine hours was developed as $H_{av} =(1.546\frac{n}{N}-0.582)H_o$. Predicting the total radiation on a horizontal surface by the above equation was thought to be possible because to values of 0.882 was smaller than any t values at above 0.05 level on the basis of two tailed test of the difference between the calculated and the recorded values. 2.It was observed that optimum tilt angle of the collector in the summer and the autumn drying season was 13 degrees and 51 degrees respectively, these values could be obtained by adding or substracting approximately 25 degrees from the latitude of this area $(36.3^{\circ}N)$ .The relationship between orientation factor and declination of sun at suitable tilt angle of 33 degrees $(s=0.9\O)$ was shown at Fig.4. 3.The thermal efficiency of solar wdter collector was shown 13.4-51. 6% on Aug. 15 (the minimum radiation recorded) and 43.8 ~537% Aug.20 (the maximum radiation recorded), and 13.8~ 46.6 and 44.3~ 49.7 were shown on each corresponding day. 4.The thermal efficiency of the collectors according to the weather condition was shown a big difference of about 10% between the day of the maximum radiation recorded and the minimum, but the differen of efficiency between the air and the water collector was at most 2 ~ 3%. 5. Even if the efficiency of the solar water collector was a little higher than the solar air collector, for drying farm products, the solar air collector was thought to be more effective because the air heated by collector could be directly used for drying them.

• 한국분말재료학회지
• /
• 제24권6호
• /
• pp.472-476
• /
• 2017

Porous W-10 wt% Ti alloys are prepared by freeze-drying a $WO_3-TiH_2$/camphene slurry, using a sintering process. X-ray diffraction analysis of the heat-treated powder in an argon atmosphere shows the $WO_3$ peak of the starting powder and reaction-phase peaks such as $WO_{2.9}$, $WO_2$, and $TiO_2$ peaks. In contrast, a powder mixture heated in a hydrogen atmosphere is composed of the W and TiW phases. The formation of reaction phases that are dependent on the atmosphere is explained by a thermodynamic consideration of the reduction behavior of $WO_3$ and the dehydrogenation reaction of $TiH_2$. To fabricate a porous W-Ti alloy, the camphene slurry is frozen at $-30^{\circ}C$, and pores are generated in the frozen specimens by the sublimation of camphene while drying in air. The green body is hydrogen-reduced and sintered at $1000^{\circ}C$ for 1 h. The sintered sample prepared by freeze-drying the camphene slurry shows large and aligned parallel pores in the camphene growth direction, and small pores in the internal walls of the large pores. The strut between large pores consists of very fine particles with partial necking between them.

• 농업과학연구
• /
• 제9권1호
• /
• pp.357-370
• /
• 1982

태양열(太陽熱)을 이용(利用)한 곡물(穀物)의 건조(乾燥)와 저장(貯藏)을 겸할 수 있는 농가용(農家用) 태양열(太陽熱) 저장고(貯藏庫)의 개발(開發)에 필요(必要)한 기초자료(基礎資料)를 얻기 위(爲)하여 구조(構造)가 간단(簡單)하고 가격(價格)이 저렴한 콘크리트 벽체의 저장고(貯藏庫)와 그 지붕을 대신(代身)한 태양열집열기(太陽熱集熱器)를 설계(設計) 제작(製作)하여 집열기(集熱器)의 성능(性能)을 실험(實驗)에 의(依)하여 구(求)하였으며 집열기(集熱器)에서 가열(加熱)된 공기(空氣)와 상온통풍(常溫通風)에 의(依)한 벼의 건조특성(乾操特性)을 비교(比較) 분석(分析)하였다. 건조(乾操)된 곡물(穀物)의 저장시(貯藏時)에 그 온도(溫度)를 예측(豫測)할 수 있는 simulation model을 개발(開發)하여 그 적합성(適合性)을 검정(檢定)하고 저장곡물(貯藏殺物)의 각(各) 부위(部位)에 대(對)한 온도(溫度)의 변화(變化)를 분석(分析)한 결과(結果)들을 요약(要約)하면 다음과 같다. 1. 본(本) 실험(實驗)에 설계(設計) 제작(製作)된 태양열집열기(太陽熱集熱器)의 효율(效率)은 평균(平均) 26%였으며 총열전달계수(總熱傳達係數)는 약(約) $25kJ/hr.m^2\;^{\circ}K$였다. 2. 태양열(太陽熱)을 이용(利用)한 건조(乾燥)에서는 공시(供試)벼의 함수율(含水率) 23.5%에서 15.0%까지 건조(乾燥)시키는데 7일(日)이 소요(所要)되었으며 상온통풍건조(常溫通風乾燥)에서는 함수율(含水率) 20.0%에서 15.5%까지 건조(乾燥)시키는데 12일(日)이 소요(所要)되었다. 3. 건조소요시간(乾燥所要時間)은 태양열(太陽熱)을 이용(利用)한 건조(乾燥)가 배(倍) 정도(程度) 빠르나 하층부(下層部)의 곡물(穀物)의 과건현상(過乾現象)의 방지책(防止策)이 철저히 구명(究明)되어야 할 것이다. 4. 저장곡물(貯藏殺物)의 온도(溫度)를 예측(豫測)할 수 있는 simulation model을 finite difference method에 의(依)해 개발(開發)하였으며 검정(檢定) 결과(結果) 실측치(實測値)와 잘 일치(一致)되었다. 5. 저장곡물(貯藏殺物)의 온도(溫度) 변화(變化)는 벽체와 접촉(接觸)하고 있는 부위(部位)에서 컸으며 곡물(穀物)의 손상(損傷)도 이곳에서 심(甚)할 것으로 사료(思料)된다.

• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.253-257
• /
• 2013

Freeze drying for porous Mo was accomplished by using $MoO_3$ powder as the source and camphor-naphthalene eutectic system as the sublimable material. Eutectic composition of camphor-naphthalene slurries with the initial $MoO_3$ content of 5 vol%, prepared by milling at $55^{\circ}C$ with a small amount of oligomeric dispersant, was frozen at $-25^{\circ}C$. The addition of dispersant showed improvement of dispersion stability in slurries. Pores were generated subsequently by sublimation of the camphor-naphthalene during drying in air for 48 h. To convert the $MoO_3$ to metallic Mo, the green body was hydrogen-reduced at $750^{\circ}C$, and sintered at $1100^{\circ}C$ for 2 h. The sintered samples, frozen by heated Teflon cylinder, showed large pores with the size of about 40 ${\mu}m$ which were aligned parallel to the sublimable vehicles growth direction. The formation of unidirectionally aligned pores is explained by the rejection and accumulation of solid particles in the serrated solid-liquid interface.