• The Journal of the Korean Society for Microbiology
• /
• v.21 no.1
• /
• pp.73-95
• /
• 1986

A total of 5,462 isolates suspicious of Salmonella, Shigella and E. coli which were isolated during 1983 to 1985 by 12 City Hygine Laboratories and General Hospital Laboratories were received and identified at the National Salmonella Center, Seoul, Korea. The result of identification of these strains were summarized as follows: 1. It was confirmed that the total organisms broke down into 2,014 strains of Salmonella 1,294 of which were S. typhi, 887 strains of Shigella and 2,561 strains of E. coli. 2. For seasonal distribution of enteric pathogens, July was the month with the highest out breaks of salmonellosis, May was the month of Shigellosis, and April was of the highest month it in the case of E. coli. 3. Salmonella typhi with the highest incidence of isolation was shown to belong to various phage types, especially with the strains detected in Seoul. M1 type was widely distributed all over the country, but the majority was E1 type in 1983. 4. For age distribution of patients, the 20-29 age group had the highest incidence of salmonellosis whileas the 1 to 9 age group had the highest incidence of Shigellosis. 5. For sexuly distribution of Salmonella and Shigella infections seemed to be relatively higher in the female than in the male. However, E. coli. had no relationship to both sex. 6. The antibiotic sensitivity patterns of S. typhi cultures showed a tendancy to be resistant to colistin, gentamycin, neomycin, tetracycline and streptomycin. 7. The isolates of S. paratyphi-A, S. typhimurium and S. enteritidis seemed to have a tendency of multiple drug resistance. 8. 93.9 percent of 1,568 E. coli strains showed negative reactions to the antisera of enteropathogenic E. coli and 15.6 percent of them produced a heat-labile enterotoxin, but positive reaction to the antisera was 6.1 percent and 11.6 percent of them producled the enterotoxin.

• Fire Science and Engineering
• /
• v.26 no.3
• /
• pp.106-111
• /
• 2012

In this study, EIFS (Exterior insulation finish system) of exterior cladding was applied Cone calorimeter test to confirm the effect of flame retardant. As a results, the initial ignition points in accordance with the coated form and concentration of the flame retardant was delayed. But flame resistant treatment of EIFS cladding to control the fire will not affect confirmed that. In addition, EIFS that uses high-density and low-density due to difference in the density of the impact of the fire was no difference. The exterior of the ignition experiment occurred before and after 40 seconds, heat release rate to 100 seconds appears to occur about 90 % compared with the other exterior wall materials, the initial fire spread very fast was confirmed. EIFS cladding in order to prevent the spread of fire in the application of EIFS legally use is limited by the use of the building. And flame spread can be prevented, such as a vertical outer wall compartment measures are urgently needed.

• Korean Journal of Microbiology
• /
• v.39 no.4
• /
• pp.242-247
• /
• 2003

Murine encephalomyocarditis virus (EMCV) has been used as a surrogate for hepatitis A virus (HAV) for the validation of virus removal and/or inactivation during the manufacturing process of biopharmaceuticals. Recently international regulation for the validation of HAV safety has been reinforced because of the reported cases of HAV transmission to hemophiliac patients who had received ntihemophilic factors prepared from human plasma. The purpose of the present study was to compare the resistance of HAV and EMCV to various viral inactivation processes and then to standardize the HAV validation method. HAV was more resistant than EMCV to pasteurization (60oC heat treatment for 10 hr), low pH incubation (pH 3.9 at 25oC for 14 days), 0.1 M NaOH treatment, and lyophilization. EMCV was completely inactivated to undetectable levels within 2 hr of pasteurization, however, HAV was completely inactivated to undetectable levels after 5 hr treatment. EMCV was completely inactivated to undetectable levels within 15 min of 0.1 M NaOH treatment, however, residual infectivity of HAV still remained even after 120 min of treatment. The log reduction factors achieved during low pH incubation were 1.63 for HAV and 3.84 for EMCV. Also the log reduction factors achieved during a lyophilization process of antihemophilic factor VIII were 1.21 for HAV and 4.57 for EMCV. These results indicate that HAV rather than EMCV should be used for the virus validation study and the validation results obtained using EMCV should be precisely reviewed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.4
• /
• pp.352-362
• /
• 2016

In this paper, a disposal maneuver which complies the space debris mitigation guideline was analysed for KOMPSAT-2 as an example of LEO satellite. Definition of disposal altitude which comply the '25 year rule', re-entry survivability analysis of KOMPSAT-2 parts inside and casualty area analysis were performed using STK and ESA's DRAMA. Finally, assuming that there were several survival objects during uncontrolled re-entry stage, the re-entry initial orbit elements which show the low casualty probability were found even if there were various uncertainties about the initial orbit. As a result, KOMPSAT-2 should be descended its altitude at least 43km or up to 105km to comply '25 year rule' and there were heavy or heat resistant survival objects which generated $4.3141m^2$ casualty area. And if RAAN of re-entry initial orbit was 129 degree, total casualty probability was lower than standard value of space debris mitigation guideline even if there were uncertainties about the initial orbit.

• Applied Chemistry for Engineering
• /
• v.28 no.1
• /
• pp.1-7
• /
• 2017

Polydimethylsiloxane (PDMS) can be deposited on various substrates using chemical vapor deposition process, which results in the formation of PDMS thin films with thickness below 5 nm. PDMS layers can be evenly deposited on surfaces of nanoparticles composed of various chemical compositions such as $SiO_2$, $TiO_2$, ZnO, C, Ni, and NiO, and the PDMS-coated surface becomes completely hydrophobic. These hydrophobic layers are highly resistant towards degradation under acidic and basic environments and UV-exposures. Nanoparticles coated with PDMS can be used in various environmental applications: hydrophobic silica nanoparticles can selectively interact with oil from oil/water mixture, suppressing fast diffusion of spill-oil on water and allowing more facile physical separation of spill-oil from the water. Upon heat-treatments of PDMS-coated $TiO_2$ under vacuum conditions, $TiO_2$ surface becomes completely hydrophilic, accompanying formation oxygen vacancies responsible for visible-light absorption. The post-annealed $PDMS-TiO_2$ shows enhanced photocatalytic activity with respect to the bare $TiO_2$ for decomposition of organic dyes in water under visible light illumination. We show that the simple PDMS-coating process presented here can be useful in a variety of field of environmental science and technology.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.64-68
• /
• 2020

In this study, metal copper clad laminate can be prepared using epoxy composite filled with thermally conductive fillers. In order to improve the thermal conductivity of epoxy composites, it is important factor to form conductive networks through appropriate packing of conductive fillers in epoxy composite matrix and to decrease the amount of thermally resistant junctions involving a epoxy composite matrix layer between adjacent filler units. This is because epoxy has a thermal conductivity of only 0.2-0.3W, so in order to maintain high thermal conductivity, thermally conductive fillers are connected to each other, so that the gap between particles can be reduced to reduce thermal resistance. The purpose of this study is to find way to achieve highly thermally conductive in the epoxy composite matrix filled with Al₂O₃ and Boron Nitride(BN) filler by filler loading and uniform dispersion. As a results, the use of Al₂O₃/BN hybrid filler in epoxy matrix was found to be effective in increasing thermal conductivity of epoxy composite matrix due to the enhanced connectivity offered by more continuous thermally conductive pathways and uniform dispersion without interfacial voids in epoxy composite matrix. In addition, surface treatmented s-BN improves the filler dispersion and adhesion between the filler and the epoxy matrix, which can significantly decrease the interfacial thermal resistance and increase the thermal conductivity of epoxy composite matrix.

• Journal of Dairy Science and Biotechnology
• /
• v.17 no.1
• /
• pp.1-10
• /
• 1999

A bacteriocin produced by Lab. acidophilus GP4A isolated from fecal contents of pig was characterized. Lab. acidophilus GP4A produced a heat-stable and pH-resistant bacteriocin, which was hydrolyzed by trypsin and pepsin and active against various microorganisms. Lab. acidophilus GP4A produced bacteriocin at maximum rate when grown in MRS broth(pH 6.5${\sim}$7.5) at$37^{\cric}C$ or $40^{\cric}C$. The bacteriocin produced by Lab. acidophilus GP4A inhibited the growth of Lactobacillus delbrueckii subsp. lactis 4794 in early logarithmic phase. The bacteriocin was purified by ammonium sulfate precipitation and Octyl sepharose CL-4B column chromatography. The purification resulted in a final yield of 21.7% and a 13.6-fold increase in the specific activity.

• Journal of the Korean Chemical Society
• /
• v.18 no.5
• /
• pp.381-388
• /
• 1974

When mixture of p-phenylenediamine (PPD) and m-aminophenol (MAP) were reacted with formaldehyde (F) varying their amounts under $N_2$ stream at the temperature of -5∼0$^{\circ}$, addition condensation reaction occurred and brown colored resins(in some cases orange colored) were formed immediately. All resins thus formed were insoluble in most ordinary organic solvents and did not melt up to 300$^{\circ}$. When the resins were treated with dilute(7 %) aqueous sodium hydroxide solution, the adsorptivity of methylene blue on them showed marked improvement reaching as much as 80 mg of methylene blue on 1 g of the resin. On the other hand, in the case of bromophenol blue, its amount of adsorption appeared 250 mg per 1 g of the resin. The TGA under $N_2$ atmosphere indicated that the resin formed in molar ratio of 1 : 3 : 8 (PPD : MAP : F) showed the best heat-resistant property among others. About 40 % weight loss was observed for this resin at 900$^{\circ}$ with heating rate of 2$^{\circ}$ per minute.

• Nuclear Engineering and Technology
• /
• v.47 no.6
• /
• pp.678-699
• /
• 2015

Although the harsh space environment imposes many severe challenges to space pioneers, space exploration is a realistic and profitable goal for long-term humanity survival. One of the viable and promising options to overcome the harsh environment of space is nuclear propulsion. Particularly, the Nuclear Thermal Rocket (NTR) is a leading candidate for nearterm human missions to Mars and beyond due to its relatively high thrust and efficiency. Traditional NTR designs use typically high power reactors with fast or epithermal neutron spectrums to simplify core design and to maximize thrust. In parallel there are a series of new NTR designs with lower thrust and higher efficiency, designed to enhance mission versatility and safety through the use of redundant engines (when used in a clustered engine arrangement) for future commercialization. This paper proposes a new NTR design of the second design philosophy, Korea Advanced NUclear Thermal Engine Rocket (KANUTER), for future space applications. The KANUTER consists of an Extremely High Temperature Gas cooled Reactor (EHTGR) utilizing hydrogen propellant, a propulsion system, and an optional electricity generation system to provide propulsion as well as electricity generation. The innovatively small engine has the characteristics of high efficiency, being compact and lightweight, and bimodal capability. The notable characteristics result from the moderated EHTGR design, uniquely utilizing the integrated fuel element with an ultra heat-resistant carbide fuel, an efficient metal hydride moderator, protectively cooling channels and an individual pressure tube in an all-in-one package. The EHTGR can be bimodally operated in a propulsion mode of $100MW_{th}$ and an electricity generation mode of $100MW_{th}$, equipped with a dynamic energy conversion system. To investigate the design features of the new reactor and to estimate referential engine performance, a preliminary design study in terms of neutronics and thermohydraulics was carried out. The result indicates that the innovative design has great potential for high propellant efficiency and thrust-to-weight of engine ratio, compared with the existing NTR designs. However, the build-up of fission products in fuel has a significant impact on the bimodal operation of the moderated reactor such as xenon-induced dead time. This issue can be overcome by building in excess reactivity and control margin for the reactor design.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.7 no.4
• /
• pp.8-16
• /
• 2004

The industrialization of central Europe more than 100 ago marked the beginning of densely concentrated buildings in quickly growing cities. A cheap type of roofing material of that time was tar. But it was dangerous because it was high inflammable. Then some roofer had a splendid idea. They used sandy material as a final layer atop the impermeable tar layer. These roofs were much more fire resistant than the typical roofs. In this sandy layer some plant species began to grow spontaneously. This was the beginning of the green roof history of modern Europe. A number of these green roofs survived both world wars. In the early 80's in Berlin alone, 50 such buildings existed and they continued to be waterproof until the present day. Since the 1992 Earth Summit of 1992 in Rio de Janeiro(http://www.johannesburgsummit.org/html/basic_info/unced.html) the term "sustainable development" became of central interest of urban designers. In city regions green roofs had become synonymous with this term. With a small investment, long-lasting roofs can be created. Further back in history, more exciting examples of green roofs can be found. The hanging gardens of antiquity are well-known. There are also green roofs built as insulation against cold and heat all over the world. For over 20 years, roof greening in central Europe has been closely examined for various reasons. Roof greening touches several different disciplines. Of primary interest is the durability of the roofs. But ecologists are also interested in green roofs, for instance in biodiversity research. The beneficial effect of greening on water proofing was also proven. For some time, the issue of fire protection was investigated. According to tests, green roofs received a harsh careful rating. Their fire protective property is considered similar to that of tile roofs. Another recent impulse for the green roof movement in Germany has come from the evident improvement of storm water retention and the reduced burden on the sewer system. The question of whether and how much energy green roofs can save has become an urgent question. The state of the research and also various open questions from a central European point of view will be discussed in the context of international collaboration. Apart from academic considerations, those who involve themselves in this issue take a predominantly positive view of the numerous existing green roofs in Germany. In some cities, green roofs are the typical construction technique for new buildings. A few outstanding examples will conclude this review. In Germany, about 20 companies, some of which operate internationally, specialize in green roof consulting. Learning from each other in an open-ended way with respect to different construction techniques and applications in various climatic regions can only be accomplished through such international collaboration as is taking place here.