• Journal of Bio-Environment Control
• /
• 제22권3호
• /
• pp.270-278
• /
• 2013

The objective of the present study is to provide data needed to decide covering method to be able to increase the thermal insulation and light transmittance efficiency of commercial greenhouse. The thermal insulation effect, PPF transmittance and quantity of condensation water were estimated in experimental tomato greenhouses covered with three types of coverings of single layer, air inflated and conventional double layers covering. The overall heat flow of air inflated double layers greenhouse was similar to that of conventional double layers greenhouse, but the temperature between covering material and thermal screen in air inflated double layers greenhouse was lower than that in conventional double layers greenhouse at the same outside temperature condition due to air leakage through the gap of roof vent. The overall heat transfer coefficients acquired by experiment that was performed in single layer and conventional double layers greenhouses were close to those obtained from model experiment. Even though the PPF transmittance of air inflated double layers greenhouse was lower than that of single layer greenhouse, which was greater than that of conventional double layers greenhouse. The quantity of condensation water on covering surface of single layer greenhouse was greater than that of air inflated double layers greenhouse due to lower covering surface temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제35권5호
• /
• pp.473-480
• /
• 2011

The proton exchange membrane (PEM) fuel cell system is critically dependent on the humidity, which should be properly maintained over the entire operating range. A membrane humidifier is used for the water management in the PEMFC because of the membrane humidifier's reliable performance and zero parasitic power loss. In the PEMFC system, the membrane humidifier is required to provide appropriate humidity for the design point of the fuel cell. Although the performance of the fuel cell depends on the performance of the humidifier, few studies have provided a systematic analysis of the humidifier. We carry out an experimental analysis of the membrane humidifier using a vapor condensation bottle. The dry air pressure, water flow temperature, and air flow rate were chosen as the operating parameters. The results show that the time constant for the dynamic response of the membrane humidifier is relatively short, but additional analysis should be carried out.

• Journal of KIISE:Computer Systems and Theory
• /
• 제36권6호
• /
• pp.532-542
• /
• 2009

Dynamic Thermal Management (DTM) technique is generally used for reducing the peak temperature (hotspot) in the microprocessors. Despite the advantages of lower cooling cost and improved stability, the DTM technique inevitably suffers from performance loss. This paper proposes the DualFloating-Point Adders Architecture to minimize the performance loss due to thermal problem when the floating-point applications are executed. During running floating-point applications, only one of two floating-point adders is used selectively in the proposed architecture, leading to reduced peak temperature in the processor. We also propose a new floorplan technique, which creates Space for Heat Transfer Delay in the processor for solving the thermal problem due to heat transfer between adjacent hot units. As a result, the peak temperature drops by $5.3^{\circ}C$ on the average (maximum $10.8^{\circ}C$ for the processor where the DTM is adopted, consequently giving a solution to the thermal problem. Moreover, the processor performance is improved by 41% on the average by reducing the stall time due to the DTM.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제18권3호
• /
• pp.122-126
• /
• 2017

The aim of this study was to develop a device for solving the heating problem of living space using heated air, utilizing a simple air heater type collector for solar energy. At the present time, this study assessed the possibility of a development system through theoretical calculations for the amount of available energy according to the size change of the air-heated solar energy collector. To produce and supply hot water using the heat energy of the sun, hot water at $100^{\circ}C$ or less was produced using a flat or vacuum tube type collector. The purpose of this study was to research the air heating type solar collector that utilizes heating energy with heating air above $75^{\circ}C$, by designing and manufacturing an air piping type solar collector that is a simpler type than a conventional solar collector system. The analysis results were obtained for the generated air temperature ($^{\circ}C$) and the production of air (kg/h) to determine the performance of air heating by an air-heated solar collector according to the heat transfer characteristics in the collector of the model when a specified amount of heat flux was dropped into a solar collector of a certain size using PHOENICS, which is a heat flow analysis program applying the Finite Volume Method. From the analysis result, the temperature of the air obtained was approximately $40.5^{\circ}C$, which could be heated using an air heating tube with an inner diameter of 0.1m made of aluminum in a collector with a size of $1.2m{\times}1.1m{\times}0.19m$. The production of air was approximately 161 m3/h. This device can be applied to maintain a suitable environment for human activity using the heat energy of the sun.

• Journal of electromagnetic engineering and science
• /
• 제5권3호
• /
• pp.126-131
• /
• 2005

To increase the efficiency of an applicator during microwave hyperthermia therapy, first, the length from the antenna end to a slot is varied to get the optimal matching of the characteristic impedance at the frequency of 2.45 GHz. Using the electric and thermal constants of biological tissue, we compose a phantom to calculate temperature increment as well as the resonance characteristics and the SAR distributions. The proposed 3-slot sleeve antenna inserted in an applicator plays an effective role in increasing the therapy size in the view of heating performance as electromagnetic energy tends to concentrate on not feed point direction but treatment area. The SAR is then used in combination with a finite difference heat transfer equation to determine the temperature distribution. Also, in order to shorten treatment time and increase therapy size, a square-array structure is suggested and analyzed.

• Journal of Hydrogen and New Energy
• /
• 제16권3호
• /
• pp.209-218
• /
• 2005

To find a suitable metal component in oxygen carrier particles for chemical-looping hydrogen generation system(CLH), oxygen transfer capacities of metal components were compared and Ni has been selected as the best metal component. The proper operating conditions to achieve high hydrogen generation rate have been investigated based on the chemical-equilibrium composition analysis for water splitting reactor. Moreover, suitable compositions of syngas from gasifier of heavy residue to achieve high energy efficiency have been investigated by calculation of heat of reaction. Based on the selected operating conditions, the best configuration of two interconnected fluidized beds system for the chemical-looping hydrogen generator has been investigated as well.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.309-310
• /
• 2002

A minimal quantity lubrication (MQL) machining is able to achieve both functions of cooling and lubrication with an extremely low quantity of a cutting fluid and a large amount of air blow. Using a biodegradable ester oil, turning tests were carried out to evaluate the effectiveness of the MQL system. It was found that the performance of MQL cutting was equivalent to, or better than, that of conventional cutting, because the MQL system tends to prevent the heat damage of the tool tip and, if an effective lubricant such as a particular polyol ester is applied to the system, it can avoid the extensive transfer of workpiece materials on to the tool surface.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.541-543
• /
• 2004

An optimal soot blowing system has been developed for an optimal operation of power utility boilers by both minimization of the use of steam and the number of soot blowers worked during soot blowing. Traditionally, the soot blowing system has been operated manually by operators. However, it causes the reduction of power and thermal performance degradation because all soot blowers installed in the plant should be worked simultaneously even there are lots of tubes those are not contaminated by slagging or fouling. Heat transfer area is divided into four groups, furnace, convection area including superheater, reheater and economizer, and air preheater in the present study. The condition of cleanness of the tubes is calculated by several parameters obtained by sensors. Then, a part of soot blowers works automatically where boiler tubes are contaminated. This system has been applied in a practical power plant. Therefore, comparison has been done between this system and manual operation and the results are discussed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• 제15권12호
• /
• pp.1043-1048
• /
• 2003

An experimental investigation was executed to determine the capacity degradation due to non-uniform refrigerant distribution in a multi-path evaporator. In addition, the possibility of recovering the capacity reduction by controlling the refrigerant distribution among refrigerant paths was assessed. The finned-tube evaporator, which had a three-path and three-depth-row, was tested by controlling inlet quality, exit pressure, and exit superheat for each refrigerant path. The capacity reduction due to superheat unbalance between each path was as much as 30%, even when the overall evaporator superheat was kept at a target value of 5.6$^{\circ}C$. It may indicate that the internal heat transfer within the evaporator assembly caused the partial capacity drop. For the evaporator having air mal-distributions, the maximum capacity reduction was found to be 8.7%. A 4.5% capacity recovery was obtained by controlling refrigerant distribution to obtain the target superheat at the outlet of each path.

• Proceedings of the KSME Conference
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1592-1597
• /
• 2004

Experimental studies were carried out to confirm the turbulent enhancement of the cooling system of nuclear reactor by large scale vortex generation in nuclear fuel rod bundle. The large scale vortex motions were generated by rearranging the inclination angles of mixing vanes to the coordinate directions. Experimental studies were carried out at Reynolds Number 60,000 with hydraulic condition. Normal variations of mean velocity and turbulent intensity in the rod bundle subchannel were measured by the 2-color LDV measurement system. The turbulence generated by split mixing vanes has small length scales so that they maintain only about 10DH after the spacer grid. On the other hand, the turbulences generated by the large scale vortex continue more and remain up $25D_{H}$ after the spacer grid.