• 제목/요약/키워드: Heat Transfer Experiment

검색결과 742건 처리시간 0.031초

공기식 흡수기를 이용한 5kW급 접시형 태양열 집열기의 열성능 해석 (Thermal Performance of Air Receiver filled with Porous Material for $5kW_t$ Dish Solar Collector)

  • 서주현;마대성;김용;서태범;강용혁;이상남;한귀영
    • 대한설비공학회:학술대회논문집
    • /
    • 대한설비공학회 2007년도 동계학술발표대회 논문집
    • /
    • pp.570-575
    • /
    • 2007
  • The thermal performance of the air receiver filled with porous material for 5kWt dish solar collector installed in Inha University, Korea, is experimentally investigated. The diameter of the parabolic dish is 3.2 m, and its focal length is 2 m. It consists of 10 small pieces of glasses which have their own curvatures, and the effective reflecting area is 5.9 m2. The reflectivity of the glass is 0.95, and the thermal capacity of the system is about 5 kW thermal. The aperture diameter of the cylindrical-shape receiver which is made of stainless steel is 100 mm, and the height is 210 mm. A quartz window is installed at the receiver aperture to minimize the convective heat loss and prevent air leakages. In order to increase the heat transfer area, porous material (nickel-alloy) is inserted into the receiver. Air flows into the upper part of the receiver, which is the opposite side of the aperture. After the air flows through the inside receiver, that goes out of the receiver through 3 exits which are located near the aperture. The volumetric flow rates of air are varied from 600 to 1200 L/min. The thermal efficiency of the receiver ranges from 82% - 92% depending upon the flow rate. The results show that the system efficiency and receiver efficiency increase as the volume flow rate increases as expected. These results from the experiment will be useful for the applications to air heating receivers and solar reactors.

  • PDF

Mn/sand 촉매를 활용한 폴리프로필렌 촉매 열분해 연구 (A Study on Catalytic Pyrolysis of Polypropylene with Mn/sand)

  • 김수현;백승훈;이루세;박상준;손정민
    • 청정기술
    • /
    • 제29권3호
    • /
    • pp.185-192
    • /
    • 2023
  • 본 연구는 '열매체 및 가스 순환형 열분해 시스템' 개발 목적으로 열분해 실험을 진행하기 전, 공정 모사용 기본 데이터 확보를 위해 수행되었다. 폐플라스틱 대체 물질로 폴리프로필렌(Polypropylene, PP)을 열분해 시료로 사용하였으며, 본 시스템에서 열전달 매체로 활용되는 유동사(이하 sand)를 사용하였다. 촉매 열분해 실험을 수행하기 위해 Mn계 물질(이하 Mn)을 촉매로 선택하였으며, sand에 담지하여 촉매 열분해 실험을 수행하였다. 열중량 분석기(Thermogravimetric analyzer, TGA)를 이용하여 PP의 기본 물성을 분석하였고, 질소 분위기 600℃ 조건에서 촉매 열분해를 통해 액상 오일을 생성하였다. 생성된 액상 오일은 GC/MS 분석을 통해 탄소 수 분포를 확인하였다. 본 연구에서는 Mn 담지 유무와 함량 변화에 따른 액상 오일 수율과 오일 내 탄화수소 분포에 미치는 영향을 조사하였다. Mn/sand를 이용하면 sand를 단독으로 활용한 열분해와 비교하여 잔여물이 감소하고 오일 수율이 증가하였다. 또한 Mn 함량 증가에 따라 액상 오일 내 C6~C9 범위 휘발유 비율이 점차 증가하였으며, 오일 내 C10보다 탄소 수가 큰 경유 및 heavy 오일 분포가 감소하는 것으로 확인되었다. 종합하면, Mn을 촉매로 활용하고 함량 변화를 통해 액상 오일 회수량을 증가시키고 생성물 내 휘발유 비율을 증가시킬 수 있을 것으로 판단하였다.

목분의 밀도변화에 따른 온도전이에 관한 실험적 연구 (Study on the Deep Stead Fire Spread Temperature by the Change of the Wood Flour Density)

  • 김진수;이동호
    • 한국화재소방학회논문지
    • /
    • 제29권3호
    • /
    • pp.1-5
    • /
    • 2015
  • 산업의 발달과 소득의 증가로 인해 목재와 같은 다공성 물질의 수요 및 생산은 지속적으로 증가하고 있다. 축산 농가를 비롯한 가공 산업 분야에서 목분의 활용이 증대됨에 따라 화재 위험도 높아지고 있다. 화재 발생시 목분은 깊이 방향으로 연소의 전이가 발생하며 내부 산화제의 소멸에 따라 화염이 없는 훈소로 진행되기도 한다. 훈소로 진행되는 경우는 화원의 위치 파악 곤란으로 초동진화에 실패하여 2차 피해를 키우는 직접적 원인으로 작용한다. 본 연구에서는 국 내외적으로 수요가 높은 뉴질랜드산 목분을 대상으로 자연대류 상태의 하향식 심부화재를 모사하였다. 본 실험에서는 실험용기 내의 목분의 체적 밀도(3%, 5%, 10%, 15%)를 변화시켜 깊이방향으로 전파되는 심부의 온도를 측정하여, 화원의 전이 속도를 실험적으로 규명하였다. 본 실험의 결과로 목분의 체적 밀도가 증가함에 따라 내부 온도는 감소하는 경향을 확인하였다. 그러나 목분 밀도체적 $0.2140g/cm^3$ (5%) 이상의 조건에서는 온도의 감소가 발생하지 않음을 실험적으로 규명하였으며 본 실험을 통하여 뉴질랜드산 소나무 목분의 온도 전이속도는 평균 0.249 mm/min의 속도 값을 가짐을 밝혔다.

MFC의 퍼지제어기 구현 (Implementation of Fuzzy Controller for MFC)

  • 이석기;이연정;이승하
    • 한국지능시스템학회논문지
    • /
    • 제14권5호
    • /
    • pp.648-654
    • /
    • 2004
  • 반도체 제조 장비에서 가스의 질량 흐름 제어기(Mass Flow Controller: MFC)가 차지하는 비중은 매우 크다. 가스의 흐름 제어가 곧 반도체 소자의 품질 및 수율을 결정하는 중요한 요소이기 때문이다. 따라서 MFC의 고속, 고정밀 제어를 구현하기 위한 요구가 높아지고 있다. MFC의 제어 알고리즘에 관한 연구 선례는 찾아보기가 매우 힘들다. 그러나 일반적으로 PID 제어 알고리즘을 사용되는 것으로 알려지고 있다. MFC 제어의 어려움은 열에 의해 흐름을 감지하는 시스템일 경우 느린 응답 특성과 비선형성을 포함한다는 데 있다. 본 논문에서는 기존의 PID 알고리즘 보다 더 우수한 성능을 보이는 MFC 제어 알고리즘을 제시하고 실험을 통해 그 우수성을 보인다. 비선형성과 느린 응답 특성을 보상하기 위하여 퍼지제어 알고리즘을 적용하였으며 그 성능을 현재 상용화된 제품과 비교하였다. 본 논문에서 제안한 알고리즘은 PC와 PC에 장착된 데이터 획득 보드를 통하여 제어루프를 형성하였고, PC상에서 LabWindows/CVI 프로그램으로 제어알고리즘을 구현하였다. 또한, 느린 응답 특성이 존재하는 센서출력으로부터 실제의 흐름을 추정하는 하나의 방법도 제시하였다. 실험결과 본 논문에서 제안하는 알고리즘이 기존의 제품보다 더 빠르고, 더 정확한 제어성능을 보였다.

막 분리 공정을 이용한 1차 계통 실리카 제거에 관한 연구 (A Study on the Silica Removal in Primary System using the Membrane Process)

  • 김봉진;이상진;양호연;김경덕;정희철;조항래
    • 한국방사성폐기물학회:학술대회논문집
    • /
    • 한국방사성폐기물학회 2005년도 춘계 학술대회
    • /
    • pp.137-144
    • /
    • 2005
  • 원전 1차 계통내에 실리카는 알카리 토금속(Ca, Mg, Al 등)과 결합하여 원전 연료 피복재에 열전달을 방해하는 규석층(Zeolite)를 형성한다. 이렇게 형성된 규석층은 원전 피복재 손상의 원인이 된다. 이러한 원전 1차 계통내 실리카의 문제점들은 EPRI 보고서 등에 그 문제점이 꾸준히 제기되어 왔으며 이러한 문제점들을 해결하기 위하여 막분리 공정을 이용하고자 하였다. 먼저 실험실 규모의 실험을 통해 NF막의 실리카 제거율이 약 $60\;{\sim}\;70\%$, Boron 제거율이 약 $10\;{\sim}\;20\%$로 그 적용 가능성을 확인하였으며, FilmTec과 Osmonics 사 NF막 제품 4종에 대하여 현장 실험을 수행하였다. 현장 사용후연료 저장 붕산수 400L를 시료로 한 실험에서 운전압력 $10kg_{f}/cm^2$에서 FilmTec 사의 NF90-2540이 실리카 제거율이 약 $98\%$, Boron 제거율이 약 $43\%$로 확인되었으며 또한 NF270-2540이 실리카 제거율이 약 $38\%$, Boron 제거율이 약 $3.5\%$로 확인되었다. 이를 바탕으로 장기운전 특성 실험 등의 추가적인 연구를 통해 최적의 실리카 제거를 위한 막 분리공정을 설계 할 예정이다.

  • PDF

임계응력 하 거친 암석 균열의 Thermoshearing 수치모델링: 국제공동연구 DECOVALEX-2023 Task G (Numerical Modeling of Thermoshearing in Critically Stressed Rough Rock Fracture: DECOVALEX-2023 Task G)

  • 박정욱;박찬희;장리;윤정석;손장윤;이창수
    • 터널과지하공간
    • /
    • 제33권3호
    • /
    • pp.189-207
    • /
    • 2023
  • In the present study, the thermoshearing experiment on a rough rock fracture were modeled using a three-dimensional grain-based distinct element model (GBDEM). The experiment was conducted by the Korea Institute of Construction Technology to investigate the progressive shear failure of fracture under the influence of thermal stress in a critical stress state. The numerical model employs an assembly of multiple polyhedral grains and their interfaces to represent the rock sample, and calculates the coupled thermo-mechanical behavior of the grains (blocks) and the interfaces (contacts) using 3DEC, a DEM code. The primary focus was on simulating the temperature evolution, generation of thermal stress, and shear and normal displacements of the fracture. Two fracture models, namely the mated fracture model and the unmated fracture model, were constructed based on the degree of surface matedness, and their respective behaviors were compared and analyzed. By leveraging the advantage of the DEM, the contact area between the fracture surfaces was continuously monitored during the simulation, enabling an examination of its influence on shear behavior. The numerical results demonstrated distinct differences depending on the degree of the surface matedness at the initial stage. In the mated fracture model, where the surfaces were in almost full contact, the characteristic stages of peak stress and residual stress commonly observed in shear behavior of natural rock joints were reasonably replicated, despite exhibiting discrepancies with the experimental results. The analysis of contact area variation over time confirmed that our numerical model effectively simulated the abrupt normal dilation and shear slip, stress softening phenomenon, and transition to the residual state that occur during the peak stress stage. The unmated fracture model, which closely resembled the experimental specimen, showed qualitative agreement with the experimental observations, including heat transfer characteristics, the progressive shear failure process induced by heating, and the increase in thermal stress. However, there were some mismatches between the numerical and experimental results regarding the onset of fracture slip and the magnitudes of fracture stress and displacement. This research was conducted as part of DECOVALEX-2023 Task G, and we expect the numerical model to be enhanced through continued collaboration with other research teams and validated in further studies.

기상청(氣象廳) 지온(地溫) 측정(測定) 토양(土壤)의 물리적(物理的) 성질(性質)과 겉보기 열확산(熱擴散) 계수(係數) 산정(算定) (Physical Properties and Apparent Thermal Diffusivity of the Soils where Soil Temperature is Measured Regularly)

  • 송관철;정영상;김병찬;안윤수;엄기태
    • 한국토양비료학회지
    • /
    • 제25권3호
    • /
    • pp.220-230
    • /
    • 1992
  • 우리나라에서 토양(土壤) 온도(溫度)를 정규적으로 관측(觀測)하고 있는 기상청(氣象廳) 산하(傘下) 기상대(氣象臺) 및 관측소(觀測所) 관측(觀測) 노장(露長)의 토양시료(土壤試料)를 채취(採取)하여 토양(土壤)의 열전도(熱傳度) 특성(特性)과 관련이 깊은 토양(土壤)의 용적밀도(容積密度), 토성(土性), 유기물(有機物) 함량(含量) 등 물리적(物理的) 특질(特質)을 분석(分析)하였으며, 토양(土壤)의 열확산(熱擴散) 계수(係數)를 산출(算出)하였다. 기상청(氣象廳) 산하(傘下) 기상대(氣象臺) 및 관측소(觀測所) 토양(土壤)의 물리적(物理的) 특성(特性)을 조사한 결과(結果) 0-10cm의 표토(表土)는 52%가 사양토(砂壤土)였으며, 양토(壤土)와 미사질양토(微砂質壤土)가 38%, 그리고 식양토(埴壤土) 및 미사질식토(微砂質埴土)가 10%이었다. 이들 토양(土壤)의 열특성(熱特性)과 관계가 깊은 용적밀도(容積密度)는 사토(砂土)가 $1.41g/cm^3$, 양토(壤土)와 미사질양토(微砂質壤土)가 $1.33g/cm^3$, 그리고 식양토9埴壤土) 및 미사질식토(微砂質埴土)가 $1.21g/cm^3$로 토성(土性)이 미세할수록 낮은 값을 보였다. 열확산(熱擴散) 계수(係數)는 평균(平均) $3.53{\times}10^{-3}cm^3/sec$이었으며, $1.159-8.401{\times}10^{-3}cm^3/sec$의 범위에 있었다. 특히 유기물(有機物) 함량(含量)이 높고 용적밀도(容積密度)가 낮은 제주도(濟州道) 토양(土壤)의 열확산(熱擴散) 계수(係數)는 표토(表土)에서 $2{\times}10^{-3}cm^3/sec$으로 다른 지역의 토양(土壤)보다 현저히 낮았다. 토심(土深) 30cm 이하(以下) 토양(土壤)의 열확산(熱擴散) 계수(係數)는 평균(平均) $6.81{\times}10^{-3}cm^3/sec$$1.54-16.12{\times}10^{-3}cm^3/sec$의 범위를 보여 표토(表土)보다 높았다. 열확산(熱擴散) 계수(係數)로부터 계산(計算)된 표토(表土)의 일주간(日週期) 불역심(不易深)(damping depth)은 5.92-13.65cm였으며, 깊이 30cm이하의 연주기(年週期) 불역심(不易深)은 124-342cm이었다. 한편, 실험실내(實驗室內)에서 열선막대법에 의하여 측정(測定)된 열확산9熱擴散) 계수(係數)와 용적밀도(容積密度) 및 토양수분함량(土壤水分含量)과의 관계로부터 열확산(熱擴散) 계수(係數)를 추정(推定)할 수 있는 중회귀(重回歸) 모델을 이용하면 토양온도(土壤溫度)가 부족한 지점(地點)의 열확산(熱擴散) 계수(係數)를 추정(推定)할 수 있게 되었다.

  • PDF

염(鹽)의 종류(種類)에 따른 격염구(隔鹽灸)의 열전달(熱傳達) 특성(特性)에 관한 실험적(實驗的) 연구(硏究) (The Experimental Study of Various Salts on the Characteristics of Heat Transfer in Indirect Moxibustion with Salt)

  • 이건목;이건휘;서은미
    • Journal of Acupuncture Research
    • /
    • 제21권1호
    • /
    • pp.119-135
    • /
    • 2004
  • Objective: The purpose of this study is to investigate the mechanism and effect of moxibustion with salt objectively, to be used as the quantitative data through the measurement of temperature, and to grasp the thermodynamic characteristics of moxibustion with salt. Methods: We have selected of the moxibustion with salt of indirect moxibustion. We make a comparative study of the thermodynamic characteristics of moxibustion with salt as a kind of the 4 salt. We examined combustion times, temperatures, temperature gradients in each period during a combustion of moxa. Results: 1. We make out that it is not significantly change the time of thermal conduction of moxibustion with salt as a kind of 4 salt. 2. The heating period of Refined Salt was long and that of Sun-dried Salt was a short time respectively. The heating period of maximum tamperature is high Sun-dried Salt, Mechanical Salt and Refined Salt orderly. Maximun heating speed in the heating period was $0.151{\sim}0.184^{\circ}C/sec$ and at the same tendency of the maximum temperature in the heating period. 3. The retaining period was shorter than the heating period respectively, that is 15~24% of the combustion time of in the heating period. We make out that it is not significantly different the time of the retaining period as a kind of 4 salt. The mean temperature of retaining period was $43.2{\sim}48.1^{\circ}C$, that was extraordinarily high temperature. 4. We make out that it is not significantly different the time of the cooling period as a kind of 4 salt. The cooling period was measured 223~233sec. Beacuse the same density and size of moxa combustion was made an experiment. 5. The effective combustion time of Refined Salt is longer(259sec) than that of Sun-dried Salt(173sec). It is significantly different the time of the combustion time as a kind of 4 salt. 6. It is significantly different the Sample deviation of the combustion time as a kind of 4 salt because of the water content of the 4 salt individually. Conclusions: As the base on this study, we obtained the conclusion as the follows. The salt of moxibustion with salt was fitted for Sun-dried Salt due to making to Mechanical Salt recently. The Refined Salt is composition rate to another and small size comparatively. So It was fitted for the salt of moxibustion with salt. It is necessary to study continuously about the more suitable moxibustion with salt and quantitative analysis about the moxibustion with salt.

  • PDF

동결농축(凍結濃縮)의 개선(改善)을 위한 기초적연구(基礎的硏究) -II. 빙결정(氷結晶)의 성장속도(成長速度)와 입경분포(粒徑分布)- (Basic Studies in Improvement of Freeze Concentration -(II) The Growth Rate and the Variety in Diameters of Ice Crystals-)

  • 공재열
    • 한국식품영양과학회지
    • /
    • 제14권4호
    • /
    • pp.359-364
    • /
    • 1985
  • 본(本) 연구(硏究)에서는 3종(種)의 잎담배 추출액(抽出液)을 시료(試料)로 하여 동결농축(凍結濃縮)에 관(關)한 기초적(基礎的) 실험(實驗)과 검토(檢討)를 행(行)하였으며, 자작(自作)한 과냉각액(過冷却液) 공급형(供給形) 연속(連續) 교반조(攪拌槽)을 써서 빙결정(氷結晶) 성장속도(成長速度)와 과냉각도(過冷却度) 및 빙결정(氷結晶)의 입경분포(粒徑分布)를 측정(測定)한 결과(結果) 다음과 같은 결론(結論)을 얻었다. 1. 공급(供給) 과냉각액(過冷却液)의 과냉각도(過冷却度) $0.2{\sim}0.6^{\circ}C$에서 빙결정(氷結晶)의 평균입경(平均粒徑)은 $0.04{\sim}0.1cm$였다. 2. 순수(純水) 및 시료용액(試料溶液)에서 생성(生成)된 빙결정(氷結晶)의 α축방향성장속도(軸方向成長速度) v는 과냉각도(過冷却度) $0.1^{\circ}C$ 이하에서 과냉각도(過冷却度)에 비례했다. 즉, v=0.058 ${\Delta}t_b$였다. 또한 농도(濃度) 20%까지의 비례상수는 농도(濃度)에 의존(依存)하지 않았다. 3. 빙결정(氷結晶) 성장속도(成長速度)는 입경(粒徑)에 의존(依存)하지 않았다. 4. 빙결정(氷結晶)의 성장속도(成長速度)는 확산(擴散)과 전열(傳熱)의 율속과정(律速過程)뿐만 아니라 결정화(結晶化) 과정(過程)도 고려하지 않으면 안된다. 5. 핵발생속도(核發生速度)는 Huige et al의 결과(結果)에 비해 현저하게 작았다. 그 원인은 조내(槽內)의 빙결정농도(氷結晶濃度)와 교반속도(攪拌速度)가 Huige et al의 실험(實驗)에 비해 매우 작았기 때문이다.

  • PDF

도로 융설체 개발을 위한 탄소나노튜브-시멘트 복합체 특성에 관한 실험적 연구 (A Feasibility Study on Developing Snow Melting Systems using CNT-Cement Composite)

  • 허진녕;박범진;김태형
    • 한국도로학회논문집
    • /
    • 제15권2호
    • /
    • pp.29-37
    • /
    • 2013
  • PURPOSES : This study aims to review the possibility of developing a road snow-melting system that can prevent slip accidents by maintaining a constant temperature of the winter roads and enhance performance of structures, including improvement of compressive strength by mixing carbon nanotube (hereafter referred to as CNT) with cement paste, the basic material. METHODS : To achieve the above purpose, an experiment was conducted by mixing power-type CNT and wrap-type CNT up to cement paste formulation by weight of 0.0wt%~4.1wt% in accordance with "KS L ISO 679(of cement strength test method)", and compressive strength was measured at 28 days of curing. In addition, the volume resistivity of the specimen was measured to test thermal and electrical characteristics, and the rate of temperature changes in specimen surface by power consumption was measured by passing electricity through the cross-sections of the specimen. Meanwhile, the criteria for checking the performance as a road snow-melting system was determined as volume resistivity of $100{\Omega}{\cdot}cm$ or less. RESULTS : A comparative analysis between specimen with 0wt% CNT content in plain status and specimen containing various types of CNTs was carried out. From its results, it was found that compressive strength increased approximately 19%, showing the highest rate when 0.2wt% of wrap-type CNT was contained, but volume resistivity of $100{\Omega}{\cdot}cm$ or less appeared only in specimens containing more than 0.2wt% CNT. In addition, it was observed that the surface temperature increased by $4.62^{\circ}C$ per minute on average in specimens containing 3.2wt% CNT. CONCLUSIONS : In this study, CNT was examined as an underlying material for a road snow-melting system, and the possibility of developing the road now-melting system was reviewed by conducting various experiments using CNT-Cement composites. From the experimental results, the specimens were found to have a superior performance when compared to the existing road snow-melting systems that place the heat transfer medium such as copper on the road. However, satisfactory strength performance were not obtained from the specimen containing CNT(2.0% or more) that functions as a heating element, which leads to the need for reviewing methods to increase the strength by using plasticizer or admixture.