• Korean journal of applied entomology
• /
• v.60 no.2
• /
• pp.193-199
• /
• 2021

Solenopsis japonica, which is belonging to Formicidae in Hymenoptera, is a native ant species in Korea. However, it had not been studied for cold hardiness of S. japonica to understand on its overwintering mechanisms in field so far. Cold tolerance on developmental stages was measured at different cold temperature with various exposure times. Workers showed more survival at 5℃ and 10℃ compared with other stages and elevated cold tolerance when workers were exposed at 15℃ for more than 12h incubation as a rapid cold hardening (RCH) condition. RCH treatment not only increased survival of workers at cold temperatures, but also decreased supercooling point (SCP) and freezing point (FP). RCH group increased the survival rate by 44% at 10℃ compared with Non-RCH group. SCP and FP were depressed from -10.0 to -14.2℃ and from -11.3 to -15.3℃, respectively, after RCH treatment. Cold temperature increased expression level of cold- and stress-related genes such as glycerol kinase and heat shock protein. These results indicate unacclimated cold tolerance of S. japonica and its acclimation to low temperature by RCH.

• The Plant Pathology Journal
• /
• v.23 no.3
• /
• pp.174-179
• /
• 2007

Seedlot disinfection techniques to control mung bean sprout rot caused by Colletoricum acutatum and C. gloeosporioides were evaluated for commercial production scheme. Soaking seedlots in propolis (100 X) and ethanol (20% for 30 min) appeared promising with control values of 85.5 and 80.8 respectively, but still resulted in up to 20% rot incidence. None of the C. acutatum conidia survived through hot water immersion treatment (HWT) for 10 min at temperatures of 55, 60 and $65^{\circ}C$, whereas the effective range of the dry heat treatment (DHT) was $60-65^{\circ}C$. Tolerance of mung bean seedlot, as estimated by hypocotyl elongation and root growth, was lower for HWT than for DHT. Germination and growth of sprouts were excellent over the range of $55-65^{\circ}C\;at\;5^{\circ}C$ intervals, except for HWT at $65^{\circ}C$ for 5 min. At this marginal condition, heat damage appeared so that approximately 2% of seeds failed to sprout to normal germling and retarded sprouts were less than 5% with coarse wrinkled hypocotyls. These results suggested that DHT would be more feasible to disinfect mung bean seedlots for commercial sprout production. Heat treatment at above ranges was highly effective in eliminating the epiphytic bacterial strains associated with marketed sprout rot samples. HWT of seedlot at 55 and $60^{\circ}C$ for 5 min resulted in successful control of mung bean sprout rot incidence with marketable sprout quality. DHT at 60 and $65^{\circ}C$ for 30 min also gave good results through the small-scale sprouting system. Therefore, we optimized DHT scheme at 60 and $65^{\circ}C$ for 30 min, considering the practical value of seedlot disinfection with high precision and accuracy. This was further proved to be a feasible and reliable method against anthracnose incidence and those bacterial strains associated with marketed sprout rot samples as well, through factory scale mung bean sprout production system.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.1
• /
• pp.1-18
• /
• 2013

The elements that determine the success of development projects on goats and the prerequisites for ensuring this are discussed in the context of the bewildering diversity of goat genetic resources, production systems, multifunctionality, and opportunities for responding to constraints for productivity enhancement. Key determinants for the success of pro-poor projects are the imperatives of realistic project design, resolution of priorities and positive impacts to increase investments and spur agricultural growth, and appropriate policy. Throughout the developing world, there exist 97% of the total world population of 921 million goats across all agroecological zones (AEZs), including 570 breeds and 64% share of the breeds. They occupy a very important biological and socioeconomic niche in farming systems making significant multifunctional contributions especially to food, nutrition and financial security, stability of farm households, and survival of the poor in the rural areas. Definitions are given of successful and failed projects. The analyses highlighted in successful projects the value of strong participatory efforts with farmers and climate change. Climate change effects on goats are inevitable and are mediated through heat stress, type of AEZ, water availability, quantity and quality of the available feed resources and type of production system. Within the prevailing production systems, improved integrated tree crops - ruminant systems are underestimated and are an important pathway to enhance C sequestration. Key development strategies and opportunities for research and development (R and D) are enormous, and include inter alia defining a policy framework, resolution of priority constraints using systems perspectives and community-based participatory activities, application of yield-enhancing technologies, intensification, scaling up, and impacts. The priority for development concerns the rainfed areas with large concentrations of ruminants in which goats, with a capacity to cope with heat tolerance, can be the entry point for development. Networks and networking are very important for the diffusion of information and can add value to R and D. Well formulated projects with clear priority setting and participatory R and D ensure success and the realisation of food security, improved livelihoods and self-reliance in the future.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.9 s.186
• /
• pp.54-60
• /
• 2006

Fitting process carried out in automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that heats gear to a suitable range under the tempering temperature and squeezes it toward the outer diameter of shaft. Its stress depends on the yield strength of gear. Press fitting is a method that generally squeezes gear toward that of shaft at room temperature by press. Another method heats warmly gear and safely squeezes it toward that of shaft. Warm shrink fitting process for automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by this process produced dimensional changes of gear profile in both radial and circumferential directions. So that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of warm shrink fitting process, in which design parameters are involved; contact pressure according to fitting interference between outer diameter of shaft and inner diameter of gear, fitting temperature, and profile tolerance of gear. In this study, an closed form equation to predict contact pressure and fitting load was proposed in order to develop optimization technique of warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, that is, thermal-structural coupled field analysis. Actual loads measured in the field have a good agreement with the results obtained by theoretical and finite element analysis and also the expanded amounts of the gear profile in both radial and circumferential directions are within the limit tolerances used in the field.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.37-43
• /
• 2006

Fitting process carried out in automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that heats gear to a suitable range under the tempering temperature and squeezes it toward the outer diameter of shaft. Its stress depends on the yield strength of gear. Press fitting is a method that generally squeezes gear toward that of shaft at room temperature by press. Another method heats warmly gear and safely squeezes it toward that of shaft. Warm shrink fitting process for automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by this process produced dimensional change in both outer diameter and profile of the gear. So that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of warm shrink fitting process, in which design parameters are involved; contact pressure according to fitting interference between outer diameter of shaft and inner diameter of gear, fitting temperature, and profile tolerance of gear. In this study, an closed form equation to predict contact pressure and fitting load was proposed in order to develop optimization technique of warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, that is, thermal-structural coupled field analysis. Actual loads measured in the field have a good agreement with the results obtained by theoretical and finite element analysis and also the expanded amounts of the outer diameters of the gears have a good agreement with results.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.254-260
• /
• 2005

By incorporating large core polymer waveguides, which have been developed for increased alignment tolerance in passive fiber attachment, highly efficient variable optical attenuators are proposed. In order to find optimum device structures, 3-dimensional beam propagation method (BPM) simulations are performed. Heat distribution over the polymer film is calculated to find the 3-dimensional index profile data for the BPM simulation. Due to the small index contrast between the core and cladding materials in the large core waveguide, heat-induced radiation occurs for small heating power. While the ordinary VOA needs the temperature to change over $150^{\circ}C$ for 20 dB attenuation, the large core VOA requires only $70^{\circ}C$. In addition to the merit of passive fiber attachment, the proposed VOA has enhanced attenuation efficiency for the lower temperature change.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.6
• /
• pp.47-54
• /
• 2008

Fitting process carried out in the automobile transmission assembly line is classified into three classes; heat fitting, press fitting, and their combined fitting. Heat fitting is a method that heats gear to a suitable range under the tempering temperature and squeezes it toward the outer diameter of shaft. Its stress depends on the yield strength of gear. Press fitting is a method that generally squeezes gear toward that of shaft at room temperature by a press. Another method heats warmly gear and safely squeezes it toward that of shaft. Warm shrink fitting process for the automobile transmission part is now gradually increased, but the parts (shaft/gear) assembled by this process produced dimensional changes in both the outer diameter and profile of the gear. So that it may cause noise and vibration between gears. In order to solve these problems, we need an analysis of warm shrink fitting process, in which design parameters are involved; contact pressure according to fitting interference between outer diameter of shaft and inner diameter of gear, fitting temperature, and profile tolerance of gear. In this study, an closed form equation to predict contact pressure and fitting load was proposed in order to develop an optimization technique of the warm shrink fitting process and verified its reliability through the experimental results measured in the field and FEM, that is, thermal-structural coupled field analysis. Actual loads measured in the field was in good agreements with the results obtained by the theoretical and finite element analysis.

• Research in Plant Disease
• /
• v.29 no.3
• /
• pp.321-329
• /
• 2023

The bacterium Neobacillus endophyticus BRMEA1^T, isolated from the medicinal plant Selaginella involvens, known as its thermotolerant can grow at 50℃. To explore the genetic basis for its heat tolerance response and its potential for producing valuable natural compounds, the genomes of two thermotolerant and four mesophilic strains in the genus Neobacillus were analyzed using a bioinformatic software platform. The whole genome was annotated using RAST SEED and OrthVenn2, with a focus on identifying potential heattolerance-related genes. N. endophyticus BRMEA1^T was found to possess more stress response genes compared to other mesophilic members of the genus, and it was the only strain that had genes for the synthesis of osmoregulated periplasmic glucans. This study sheds light on the potential value of N. endophyticus BRMEA1^T, as it reveals the mechanism of heat resistance and the application of secondary metabolites produced by this bacterium through whole-genome sequencing and comparative analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.58-67
• /
• 2000

Electron gun heaters are used to heat a cathode in video(TV) monitors. Major defects of the electron gun heaters include dimensional inaccuracy and pollution with dirty materials. In this paper, to save the labor and time being taken to inspect the heaters, a machine vision system is considered. For the system, a new algorithm is developed to measure the 9 different dimensions of each heater and to detect polluted defects. The algorithm consists of three stages. In the first stage, the center of the heater image is obtained and then its boundary detection is performed. For the efficient boundary detection, a mask called the sum mask is used. In the second stage of the algorithm, a set of fiducial points are determined on the boundary image. Finally, using the fiducial points specified dimensions are measured and the amount of polluted area is computed in the third stage. The performance of the algorithm is evaluated for a set of real specimens. The results indicate that measurements obtained by the algorithm satisfy the tolerance limits fur most of the dimensions and the algorithm detects the polluted defects successfully.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.2
• /
• pp.314-324
• /
• 1997

The purpose of this study was to evaluate the thermoregulatory response level on the heat and cold tolerance with investigating monthly changes of skin temperature in Koreans and to obtain the basal information for standard amount of clothing weight, indoor climate and working condition. Forty eight subjects in 5 age groups (6~11, 12~19, 20~44, 45~64, 65~76 years old) with both sexs were taken from Seoul and Kyunggi probince. All subjects were measured skin temperature, mean skin temperature, Total clothing weight in neutral condition in each month from June 1994 to May 1995. The results obtained are summarized as follows: 1. Skin temperature of all subjects was low on February, March and April, and was high on June, July and August. Temperatures of the torso (forehead and abdomen) and the lower limbs (leg and foot) were remarkably different. In general, most of skin temperatures except of hand, thigh and foot were higher in males. 2. Mean skin temperature was 0.5'c higher in males than female with ranging 32.5~34.5$^{\circ}C$ in males and 32.1~34.1$^{\circ}C$ in females. Also, mean skin temperature of 6~11 age group were higher than that of 45~ 64 age group in both sexs.