• 설비공학논문집
• /
• 제19권6호
• /
• pp.434-440
• /
• 2007

One of the cold start problems of a FCV is the freezing of the water in the water tank when a FCV is not in operation and the surrounding temperature drops below $0^{\circ}C$. The ice in the tank should be melted as quickly as possible for a satisfactory operation of fuel cell vehicles. In this study, the melting process for the constant heat fluxes of the plate heaters was numerically calculated in the 2-D model of the tank and plate heaters. The enthalpy method and FVM code was used for this analysis. The changes of the temperature with heat fluxes and the heat transfer area could be investigated. The energy balance error was found to increase with the heat flux. From this numerical analysis, the proper heat flux value and some important design factors relating local overheating and pressurization of the water tank could be examined.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.261-266
• /
• 2003

The present paper theoretically investigates characteristics of moment balance of a tilting-pad thrust bearing. Pressure of lubricant film of the bearing was computed using tile finite element method, and average film temperature was estimated from the heat balance over a pad. From the investigation, it has been found that different two sets of tilt angles satisfy moment equilibrium of the pad about tile pivot for a given pivot location. The tilt angles converged depend upon initial tilt angles assumed. Quite different bearing performance, including load capacity, film thickness, and temperature, is shown to be obtained based on choice of the initial tilt angles.

• Tribology and Lubricants
• /
• 제20권3호
• /
• pp.152-156
• /
• 2004

The present paper theoretically investigates characteristics of moment balance of a tilting-pad thrust bearing. Pressure of lubricant film of the bearing was computed using the finite element method, and average film temperature was estimated from the heat balance over a pad. From the investigation, it has been found that different two sets of tilt angles satisfy moment equilibrium of the pad about the pivot for a given pivot location. The tilt angles converged depend upon initial tilt angles assumed. Quite different bearing performance, including load capacity, film thickness, and temperature, is shown to be obtained based on choice of the initial tilt angles.

• 환경영향평가
• /
• 제31권1호
• /
• pp.63-74
• /
• 2022

도시 지역의 열 환경을 파악하기 위해 열 플럭스를 추정하고자 하는 연구들이 많이 진행되어 왔다. 현재 다양한 방법을 통해 현열 플럭스가 추정되고 있으나 각 방법 간의 차이를 비교하는 연구는 매우 미흡한 실정이다. 따라서 본 연구는 대표적인 두 가지 현열 플럭스 추정 방법을 통해 동일한 대상지의 현열 플럭스를 추정하고 그 결과를 비교하여 방법 간의 의의와 한계를 확인하고자 하였다. 연구 결과 열수지 방정식 방법을 통해 현열 플럭스를 추정할 경우 해상도면에서 큰 장점을 가지나 도시 지역의 특징 중 하나인 인공열을 반영하지 못해 현열이 과소추정될 수 있음을 확인할 수 있었다. 물리식을 기반으로 추정할 경우 상대적으로 오차가 작고 인공열의 반영이 가능하나, 시간 및 공간 해상도에 있어 한계가 있음을 확인하였다. 두 방법은 인공열이 많이 발생하는 공업지역에서 가장 큰 차이를 나타냈으며 그 차이는 평균 약 135 W/m², 최대 400 W/m²로 나타났다. 반면 녹지 및 수변공간은 약 20 W/m²로 두 방법 간의 차이가 매우 작은 것을 확인할 수 있었다. 두 방법 간의 결과가 도시 지역에서 유의미한 차이를 보이는 만큼 향후 연구 목적에 맞는 방법을 선택할 필요가 있다.

• 대한한의학회지
• /
• 제42권4호
• /
• pp.185-196
• /
• 2021

Objectives: Many symptoms of cold and heat patterns are related to the thermoregulation of the body. Thus, we aimed to study the association of cold and heat patterns with anthropometry/body composition. Methods: The cold and heat patterns of 2000 individuals aged 30-55 years were evaluated using a self-administered questionnaire. Results: Among the anthropometric and body composition variables, body mass index (-0.37, 0.39) and fat mass index (-0.35, 0.38) had the highest correlation coefficients with the cold and heat pattern scores after adjustment for age and sex in the cold-heat group, while the correlation coefficients were relatively lower in the non-cold-heat group. In the cold-heat group, the most parsimonious model for the cold pattern with the variables selected by the best subset method and Lasso included sex, body mass index, waist-hip ratio, and extracellular water/total body water (adjusted R² = 0.324), and the model for heat pattern additionally included age (adjusted R² = 0.292). Conclusions: The variables related to obesity and water balance were the most useful for predicting cold and heat patterns. Further studies are required to improve the performance of prediction models.

• 터널과지하공간
• /
• 제23권3호
• /
• pp.241-259
• /
• 2013

충전층을 이용한 열에너지저장 시스템은 자갈이나 콘크리트와 같은 열저장매질과 공기나 오일과 같은 열전달유체를 이용하여 현열에너지를 저장하는 방식으로서, 저장매질의 경제성과 화학적 안정성, 시스템 구축의 용이성 등 많은 장점이 갖는다. 본 연구에서는 충전층을 이용한 열에너지저장 기술에 대하여 개략적으로 소개하고, 이러한 열에너지저장소의 에너지 수지와 성능 효율을 분석하기 위한 수치 모델을 제시하였다. 유한차분법을 이용하여 저장소 내 1차원 비정상 열전달 해석을 수행하였으며, 반복적인 주입과 토출에 따른 충전층의 온도분포와 외부로의 손실 에너지를 계산하였다. 해석모델은 AA-CAES(advanced adiabatic compressed air energy storage)와 연계된 고온의 열에너지저장시스템으로 저장소가 지하암반 내에 위치하는 경우와 지상에 위치하는 경우를 모사하고, 성능효율 및 열손실률을 비교 분석하였다.

• 설비공학논문집
• /
• 제27권3호
• /
• pp.123-127
• /
• 2015

Thermochemical heat storage is a cutting-edge technology which can balance the energy usage between supplies and demands. Recent studies have suggested that thermochemical heat storage has significant advantages, compared to other storage methods such as latent heat storage or sensible heat storage. Nevertheless, ongoing research and development studies showed that the thermochemical heat storage has some serious problems. To bring the thermochemical heat storage method into market, we introduce experimental setup with composite material using perlite that supports calcium chloride sorbent. Also, to compare thermal properties with composite material, we used pure thermochemical material. Then, we found that the composite material has higher heat storage density by mass than pure calcium chloride. Moreover, it can be easily regenerated, which was impossible in the pure thermochemical materials.

• 대한기계학회논문집B
• /
• 제23권10호
• /
• pp.1213-1222
• /
• 1999

A finite element method is developed for calculating the temperature and enthalpy distribution and accordingly the solid, liquid and mushy zone in a three-dimensional body subjected to any heat boundary conditions. The method concurrently consider both temperature and enthalpy for consideration of the latent heat effect, differently from other methods of using a special energy balance equation for solving a mushy zone. The developed brick element has eight nodes with one degree of freedom at each node. The numerical method and procedure are verified using the results of one and two dimensional analytic solutions and by other researchers. It is shown that the present method presents a consistent and stable results in either abrupt or ranged phase change problems. Moreover, the numerical results by the present method are hardly effected by the calculation time steps which otherwise are difficult to determine in most phase change problems. Finally, as a three-dimensional application, a T-shaped body of a phase change is presented and the temperature and enthalpy variation along the time are solved.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1992년도 춘계학술대회 논문집 92
• /
• pp.177-200
• /
• 1992

A thermo-viscoplastic finite element program was developed to analyze the compression molding of SMC process. Deformation of the material was modelled by using the flow-rule. Heat balance during the process was coupled to the deformation. In the cure study, a kinetic model was adopted to describe the cure behavior. The numerical kinetic model was integrated with the thermo-viscoplastic numerical analysis by adding heat generation due to the chemical reaction of the workpiece in the heat transfer analysis. The integrated finite element program can simulate a whole sequential molding process including deformation, heat transfer, and chemical reaction. A practical SMC molding process with T-shaped substructure was simulated. The simulated results showed good agreements with experiments.

• 한국생산제조학회지
• /
• 제8권1호
• /
• pp.28-34
• /
• 1999

According to the development of tool material and the improvement of machinability of cutting material like aluminium alloy, the higher spindle speed is needed. However, the higher speed causes the heat generation of bearings, the deformation of spindle unit parts, and the rotational accuracy of spindle to be worse. Therefore, it is essential to analyze and control the heat generation and the thermal behavior of spindle unit in order to have higher speed and better rotational accuracy. This paper shows the analogy between the analyzation of heat generation and thermal behavior of high speed spindle system by finite element method and the test results of actual temperature rise through running test, and shows the necessity of cooling the spindle and inner ring side of bearings for the thermal balance of high speed spindle system.