• Journal of Astronomy and Space Sciences
• /
• v.16 no.2
• /
• pp.159-166
• /
• 1999

As the spatial resolution of remote sensing satellites becomes higher, very accurate determination of the position of a LEO (Low Earth Orbit) satellite is demanding more than ever. Non-symmetric Earth gravity is the major perturbation force to LEO satellites. Since the orbit propagation is performed in the celestial frame while Earth gravity is defined in the terrestrial frame, it is required to convert the coordinates of the satellite from one to the other accurately. Unless the coordinate conversion between the two frames is performed accurately the orbit propagation calculates incorrect Earth gravitational force at a specific time instant, and hence, causes errors in orbit prediction. The coordinate conversion between the two frames involves precession, nutation, Earth rotation and polar motion. Among these factors, unpredictability and uncertainty of Earth rotation, called UTI-UTC, is the largest error source. In this paper, the effect of UTI-UTC on the accuracy of the LEO propagation is introduced, tested and analzed. Considering the maximum unpredictability of UTI-UTC, 0.9 seconds, the meaningful order of non-spherical Earth harmonic functions is derived.

• The Journal of the Acoustical Society of Korea
• /
• v.10 no.3
• /
• pp.72-82
• /
• 1991

The Magnetic noise generated in three phase induction motor are investigated. Total noises measured by using JEM-1313 code and sound length method and the experimental formulae are derived of magnetic fk={K+$\frac{Z_s}{P}$(1-S)}f[Hz] noise is measured in the stator of induction motor except rotor supplied from power source and their datum are analyzed and compared with one another. The experimental value of magnetic noises are equal to the theoretical value at 1440[Hz] and 1560[Hz]. The biggest magnetic harmonic is generated at 1560[Hz].

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.439-442
• /
• 2004

This paper described a dc power system, which can generate the excessive do power form do bus line to ac source in substation for traction system. The proposed regeneration inverter system for dc traction can be used as both an inverter and an active power filter(APF). As a regeneration inverter mode, it can recycle regenerative energy caused by decelerating tractions and as an active power filter mode, it can compensate for harmonic distortion produced by the rectifier substation.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.287-289
• /
• 1988

A reactive power compensator whiych employs a 3-phase voltage source PWM converter is presented and ana lysed in this study. In this study, instantaneous reactive power compensator by the theort of instantaneous real and imaginary power are theoretically studied how to compensate reactive power occured by fundamental and harmonic reactive current. And we showed the compensation characteristic as well as the capacity of condenser.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.5
• /
• pp.185-192
• /
• 1986

This paper deals with the general mathmatical model of the CSI-fed induction motor system. The inverter is represented by a switching function matrix which is combined with the dg model of an induction motor. Complete system model is given by a set of differential equations in a closed form, which inherently includes the harmonic effects of the converter and the inverter. The model is valid in evaluating both the transient and steady state responses, while the more simple analytical model can be derived from the general model, in a steady state. With the model proposed, the digital simulation is carried out on a 10KVA CSI-induction motor system and the simulation results show good agreements with experimental ones.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.6
• /
• pp.906-915
• /
• 1994

Line-Current harmonics resulting from ac to dc power conversion interfere with power system operation and reduce power factor, hence resulting in increasing power source unnecessarily. This study describes a 3 phase phase-controlled converter eliminating low frequency harmonics in the output by inserting notches. Notch points are calculated by Newton-raphson method, The impacts of the choppings on ac and dc sides are analyzed in the steady state. Potential applications of the study are dc motor controls, high power dc power supplies for telecommunications, static var compensators and HVDC.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.4
• /
• pp.369-378
• /
• 1992

This paper proposes a utility parallel processing inverter system, which consists of a voltage source PWM inverter, isolation transformer and a reactor linking the inverter to utility line. This system realizes following functions : (1) voltage phase frequency and amplitude synchronization between inverter and utility line at stand-alone mode. (2) current phase synchronization between inverter and load at parallel mode. Therefore, despite sudden increase in load current over setting point at stand-alone mode, inverter system can be transferred into parallel mode immediately without transient current. Furthermore, high frequency(18KHz) PWM control and sinusoidal filtering improve the inverter output waveform by eliminating high order harmonic components as well as low order. As a switching device, IGBT is used for high frequency switching and large current capacity.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2641-2643
• /
• 1999

This paper describes the first field demonstration of the distribution STATCON in Korea including installation and its evaluation for improving power quality in distribution system. The purpose of installation is to verify functionally the voltage source inverter based equipment for voltage regulation and harmonic mitigation in distribution line. The operational data resulting from field test and the site figure are included.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.4
• /
• pp.29-35
• /
• 2003

The rotating machineries always generate harmonic frequencies of their own rotating speed, and increment of vibration amplitude affects to the equipments which connected to the vibrational source and causes industrial calamities. The life cycle of equipments can be extended and damages to the human beings could be prevented by identifying the cause of malfunctions through prediction of the increment of vibration and records of vibrational history. In this study, therefore, diagnostic expert algorithm for the centrifugal pump is developed by integrating fuzzy inference method and signal processing techniques. And the validity of the developed diagnostic system is examined via various computer simulations.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.616-619
• /
• 2003

Photochemical and photothermal effects have correlation with each other and depend on laser wavelength. Multi-scanning laser ablation process of polymer with DPSS(Diode Pumped Solid State) 3rd harmonic Nd:YVO$_4$ laser with wavelength of 355nm is applied to fabricate three-dimensional micro shape. The DPSSL photomachining system can rapidly and cheaply fabricate 2D pattern or 3D shape with high efficiency because we only use CAD/CAM software and precision stages instead of complex projection mask. Photomachinability of polymer is highly influenced by laser wavelength and its own chemical structure. So the optical characteristics of polymers for 355nm laser source is investigated by experimentally and theoretically.