• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.710-716
• /
• 2007

In this paper, I study on the realization of 900 MHz 1 W power amplifier using a harmonic rejection circuit. The proposed harmonic rejection circuit has improved the harmonic rejection characteristic and overcoming the problems related with frequency reproducibility on the microstrip line. The proposed power amplifier, fabricated by the type of hybrid with the epoxy PCB, was composed of driver stage and power amplifier stage with harmonic rejection circuit. The fabricated power amplifier shows -24 dBc and -30 dBc of harmonic rejection characteristic at 2nd and 3rd harmonic compared with that is not used, respectively and it could be replace the filter located between an output stage and an antenna.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.1
• /
• pp.64-70
• /
• 2010

This paper presents how to decide on tuning factor(${\delta}$) and quality factor(Q) values in design of single-tuned passive harmonic filters. Tuning factor(${\delta}$) and quality factor(Q) values have to consider before decision on circuit parameters of passive filters. A Study on these two value has not been scarcely performed and only experienced values has been used in passive harmonic filter design by far. As a experienced value, in cases of 5th and 7th filter, tuning factor(${\delta}$) is about 0.94 and 0.96 respectively and quality factor(Q) is, in all cases of, 50. If Single-tuned passive harmonic filter will be off-tuned, performance of filter will be decreased steeply and occur to parallel resonance between system reactance and filter capacitance. Therefore During the operation, In order not to off-tuning, Filter must be tuned at former order than actual tuning order. This is the same that total impedance of filter must have a reactive impedance. In this paper, Tuning factor(${\delta}$) is decided via example of real system and using the bode-plot and then performance of filters confirmed by filter current absorbtion rate. And Quality factor(Q) decided using the bode plot in example system and then performance of filters confirmed by filter current absorbtion rate also, which makes a calculated filter parameters to satisfy IEEE-519 distortion limits. Finally, Performance of the designed passive harmonic filter using the tuning factor(${\delta}$) and quality factor(Q) values, decided in this paper is verified by experiment and shows that 5th, 7th, 9th, 11th and 13th current harmonic distortions are decreased within IEEE-519 distortion limits, respectively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.3
• /
• pp.211-219
• /
• 2014

Closed cracks are difficult to detect using conventional ultrasonic testing because most incident ultrasound passes completely through these cracks. Nonlinear ultrasound inspection using sub-harmonic frequencies a promising method for detecting closed cracks. To implement this method, a sub-harmonic phased array (PA) is proposed to visualize the length of closed cracks in solids. A sub-harmonic PA generally consists of a single transmitter and an array receiver, which detects sub-harmonic waves generated from closed cracks. The PA images are obtained using the total focusing method (TFM), which (with a transmitter and receiving array) employs a full matrix in the observation region to achieve fine image resolution. In particular, the receiving signals are measured using a laser Doppler vibrometer (LDV) to collect PA images for both fundamental and sub-harmonic frequencies. Oblique incidence, which is used to boost sub-harmonic generation, inevitably produces various surface waves that contaminate the signals measured in the receiving transducer. Surface wave interference often degrades PA images severely, and it becomes difficult to read the closed crack's position from the images. Various methods to prevent or eliminate this interference are possible. In particular, enhancing images with signal processing could be a highly cost-effective method. Because periodic patterns distributed in a PA image are the most frequent interference induced by surface waves, spatial frequency filtering is applicable for removing these waves. Experiments clearly demonstrate that the spatial frequency filter improves PA images.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.2
• /
• pp.68-79
• /
• 2003

We estimated harmonics on power system of AC railway based on quantitatively measured harmonics and investigated the need of facilities for harmonics reduction. In order to analysis harmonics which inflow into power system due to increase in collector voltages and harmonic currents generated from the train when the railway is in operation, the railway system Is sectioned into power supply, railway line, AT, sectioning Post and subsectioning post. For analysis of extension of currents resulting from the railway loads, PWM converter, VVVF inverter and the feeder system are modeled based on the dynamic node technique(DNT). In order to test the usefulness of the DNT for analysis of harmonic effects, the measured harmonic currents and harmonic magnification ratios at the S/K substation are compared with simulation results using DNT modelling, which include the results for two cases with and without filters for suppression of harmonic currents. When 8 cars(4M4T) are in operation, the total sum of harmonic currents resulting from the train at M and T phases, which inflow into the substation along with the railway line, is calculated. Using the harmonics analysis program for railway feeder system with these data, the total harmonic distortion factor(710) at the outgoing point of KEPCO substation is computed. The calculation shows that when the maximum THD at the receiving point of H/K substation was 0.0443% which is much lower than 1.5% which is the allowable value of KEPCO at 154kV as well as IEEE-519 above 132kV This result indicates that any measure for harmonics reduction in Incheon International Airport Railway is not needed.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.73-78
• /
• 2004

In this paper, it is designed for 5.8GHz Wireless LAN sub harmonic resistive mixer. Sub harmonic resistive mixer is constituted by advantage of sub harmonic mixer and resistive mixer. Sub harmonic resistive mixers mix harmonics of LO with RF and obtain IF frequency. Therefore, it was possible to use decreasing LO frequency than conventional mixers. And, Sub harmonic resistive mixer has low IMD because of using unbiased channel resistance of GaAs FET. When LO power is 13dBm, the conversion loss of manufactured sub harmonic resistive mixer is 10.67 dB. And IIP3 of mixer is 21.5dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.49-55
• /
• 2005

In this paper, the phase locked harmonic oscillator(PLHO) using the analog PLL(Phase Locked Loop) is designed and implemented for a wireless LAN system. The harmonic oscillator is consisted of a ring resonator, a varactor diode and a PLL circuit. Because the fundamental fiequency of 8.5 GHz is used as the feedback signal for the PLL and the 2nd harmonic of 17.0 GHz is used as the output, a analog frequency divider for the phase comparison in the PLL system can be omitted. For the simple PLL circuit, the SPD(Sampling Phase Detector) as a phase comparator is used. The output power of the phase locked harmonic oscillator is 2.23 dBm at 17 GHz. The fundamental and 3rd harmonic suppressions are -31.5 dBc and -29.0 dBc, respectively. The measured phase noise characteristics are -87.6 dBc/Hz and -95.4 dBc/Hz at the of offset frequency of 1 kHz and 10 kHz from the carrier, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.2
• /
• pp.89-95
• /
• 2003

In this paper, we have designed and fabricated high conversion gain Q-band active sub-harmonic mixers for a receiver of millimeter wave wireless communication systems. The fabricated active sub-harmonic mixer uses 2nd harmonic signals of a low local oscillator (LO) frequency. The fabricated mixer was successfully integrated by using $0.1{\;}\mu\textrm{m}$GaAs pseudomorphic high electron mobility transistors (PHEMTs) and coplanar waveguide (CPW) structures. From the measurement, it shows that maximum conversion gain of 4.8 dB has obtained at a RF frequency of 40 GHz for 10 dBm LO power of 17.5 GHz. Conversion gain from the fabricated sub-harmonic mixer is one of the best reported thus far. And a phase noise of the 2nd harmonic was obtained -90.23 dBc/Hz at 100 kHz offset. The active sub-harmonic mixer also ensure a high degree of isolations, which are -35.8 dB from LO-to-IF and -40.5 dB from LO-to-RF, respectively, at a LO frequency of 17.5 GHz.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.3
• /
• pp.26-34
• /
• 2000

In this paper, we propose a 4kbps speech coder that combines the harmonic vector excitation coding with time-separated transition coding. The harmonic vector excitation coding uses the harmonic excitation coding in the voiced frame and uses the vector excitation coding with the structure of analysis-by-synthesis in the unvoiced frame, respectively. But two mode coding method is not effective for transition frame mixed in voiced and unvoiced signal and a new method beyond using unvoiced/voiced mode coding is needed. Thus, we designed a time-separated transition coding method for transition frame in which a voiced/unvoiced decision algorithm separates unvoiced and voiced duration in a frame, and harmonic-harmonic excitation coding and vector-harmonic excitation coding method is selectively used depending on the previous frame U/V decision. In the decoder, the voiced excitation signals are generated efficiently through the inverse FFT of harmonic magnitudes and the unvoiced excitation signals are made by the inverse vector quantization. The reconstructed speech signal are synthesized by the Overlap/Add method.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.2
• /
• pp.75-82
• /
• 1999

A compensation method of the motor parameters using zero sequence third harmonic voltage is presented for the speed sensorless vector control of the induction motor considering saturation of the flux. Generally, the air-gap flux of the saturated induction motor contains the space harmonic components rotating with the synchronous frequency of the motor. Because the EMF of the saturated induction motor contains the zero sequence harmonic voltages at the neutral point of the motor, those harmonic voltages can be used as a saturation index. In this work, the rotor flux observer is firstly designed for the speed sensorless vector control of induction motor. And a novel measurement method of the space harmonic voltage and a compensation method of th LPF(Low Pass Filter) are proposed. For compensating the non-linear variations of the magnetizing inductance depending on the saturation level of the motor, the dominant third harmonic voltage of the motor is used as a saturation function of the air-gap flux. And the variation of the stator resistance owing to the motor temperature can also be measured with the phase angle between the impressed voltage vector and the zero sequence voltage. The validity of the proposed parameter compensation scheme in the speed sensorless vector control using rotor flux observer is verified by the result of the simulations and the experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.36-42
• /
• 2000

The increasing application of power electronic equipment 'especially (ASDs: adjustable speed drives)] on distribution systems has led to a growing concern for harmonic distortion and the resulting impacts on system equipment and operations. Therefore, harmonic studies have become an important aspect of power system analysis and design in recently years. Computer simulations which is related harmonic are used to quantify the distortion in voltage waveforms in a power system. Many digital computer programs are available for harmonic analysis. In frequency spectrum analysis, Simulation using SuperHarm program is superior to simulation using others. Therefore, Computer simulation using SuperHarm program is one of the effective ways to assess the harmonic effects of ASDs. The purpose of this study is to calculate the quantity of harmonic voltage by varying the ASD side load and to design the optimal harmonic filter for the elimination of harmonics.