• Geophysics and Geophysical Exploration
• /
• v.26 no.3
• /
• pp.103-113
• /
• 2023

In the oil and gas exploration market, various cableless seismic systems have been developed as an alternative to improve data acquisition efficiency. However, developing such equipment at a small scale for academic research is not available owing to highly priced commercial products. Fortunately, building and experimenting with open-source hardware enable the academic utilization of cableless seismic equipment with relatively low cost. This study aims to develop a cableless seismic acquisition module using Arduino. A cableless seismic system requires the combination of signal sensing, simple pre-processing, and data storage in a single device. A conventional geophone is used as the sensor that detects the seismic wave signal. In addition, it is connected to an Arduino circuit that plays a role in implementing the processing and storing module for the detected signals. Three main functions are implemented in the Arduino module: preprocessing, A/D conversion, and data storage. The developed single-channel module can acquire a common receiver gather from multiple source experiments.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.26 no.1
• /
• pp.91-101
• /
• 2023

Modeling and Simulation(M&S) technology has been widely used to solve constraints such as time, space, safety, and cost when we implement the same development and test environments as real warfare environments to develop, test, and evaluate weapon systems for the last several decades. The integration and test environments employed for development and test & evaluation are required to provide Live Virtual Construction(LVC) simulation environments for carrying out requirement analysis, design, integration, test and verification. Additionally, they are needed to provide computing environments which are possible to reconfigure computing resources and software components easily according to test configuration changes, and to run legacy software components independently on specific hardware and software environments. In this paper, an Integration Test and Simulation for Engagement Control(ITSEC) bed using a bare-metal virtualization mechanism is proposed to meet the above test and simulation requirements, and it is applied and implemented for an air missile defense system. The engagement simulation experiment results conducted on air and missile defense environments demonstrate that the proposed bed is a sufficiently cost-effective and feasible solution to reconfigure and expand application software and computing resources in accordance with various integration and test environments.

• Journal of Mechanical Science and Technology
• /
• v.20 no.1
• /
• pp.85-93
• /
• 2006

The trend of miniaturization has been applied to the research of rockets to develop prototypes of micro rockets. In this paper, the development of a web-integrated prototyping system for three-dimensional micro rockets, and the results of combustion tests are discussed. The body of rocket was made of 6061 aluminum cylinder by lathe process. The three-dimensional micro nozzles were fabricated on the same aluminum by using micro endmills with ${\phi}100{\mu}m{sim}{\phi}500{\mu}m$ diameter. Two types of micro nozzle were fabricated and compared for performance. The total mass of the rockets was 7.32 g and that of propellant (gun powder) was 0.65 g. The thrust-to-weight ratio was between 1.58 and 1.74, and the flight test with 45 degree launch angle from the ground resulted in $46\;m{\sim}53\;m$ of horizontal flight distance. In addition, ABS housing for the micro machined rocket was fabricated using Fused Deposition Modeling (FDM). A web-based design, fabrication, and test system for micro nozzles was proposed to integrate the distributed hardware resources. Test data was sent to the designer via the same web server for the faster feedback to the rocket designer.

• ETRI Journal
• /
• v.36 no.5
• /
• pp.741-751
• /
• 2014

Smart TV is expected to bring cloud services based on virtualization technologies to the home environment with hardware and software support. Although most physical resources can be shared among virtual machines (VMs) using a time sharing approach, allocating the proper amount of memory to VMs is still challenging. In this paper, we propose a novel mechanism to dynamically balance the memory allocation among VMs in virtualized Smart TV systems. In contrast to previous studies, where a virtual machine monitor (VMM) is solely responsible for estimating the working set size, our mechanism is symbiotic. Each VM periodically reports its memory usage pattern to the VMM. The VMM then predicts the future memory demand of each VM and rebalances the memory allocation among the VMs when necessary. Experimental results show that our mechanism improves performance by up to 18.28 times and reduces expensive memory swapping by up to 99.73% with negligible overheads (0.05% on average).

• Journal of Positioning, Navigation, and Timing
• /
• v.4 no.4
• /
• pp.151-160
• /
• 2015

GPS L2C signal is a recently added civil signal to L2 frequency and is constructed by time division multiplexing of civil moderate (L2-CM) and civil long (L2-CL) code signals. While the L2-CM code is 20 ms-periodic and modulates satellite navigation message, the L2-CL code is 1.5s-periodic with 767,250 chips long code sequence and carries no data. Therefore, the L2-CL code signal allows receivers to perform a very long coherent integration. However, due to the length of the L2-CL code, the acquisition of the L2-CL code signal may take too long or require too much hardware resources. In this paper, we propose a three-step ultra-fast L2-CL code acquisition (TSCLA) technique for dual band GPS receivers. In the proposed TSCLA technique, a dual band GPS receiver sequentially acquires the coarse/acquisition (C/A) code signal at L1 frequency, the L2-CM code signal, and the L2-CL code signal to minimize mean acquisition time (MAT). The theoretical performance analysis and numerous Monte Carlo simulations show the significant advantage of the proposed TSCLA technique over conventional techniques introduced in the literature.

• Journal of Korea Multimedia Society
• /
• v.19 no.2
• /
• pp.360-374
• /
• 2016

Since WSNs (Wireless Sensor Networks) applied to their application areas such as smart home, smart factory, environment monitoring, etc., depend on sensor data, the sensor data is the most important among WSN components. The resources of each node consisting of WSN are extremely limited in energy, hardware and so on. Due to these limitation, communication failure probabilities become much higher and the communication failure causes data loss to occur. For this reason, this paper proposes 2MC (Maximum/Minimum Compression) that is a method to compress sensor data by selecting circular queue-based maximum/minimum sensor data values. Our proposed method reduces sensor data losses and value errors when they are recovered. Experimental results of 2MC method show the maximum/minimum 35% reduction efficiency in average sensor data accumulation error rate after the 3 times compression, comparing with CQP (Circular Queue Compression based on Period) after the compressed data recovering.

• Korean Journal of Computational Design and Engineering
• /
• v.17 no.2
• /
• pp.123-131
• /
• 2012

The requirements for computational resources to perform the structural analysis are increasing rapidly. The size of the current analysis problems that are required from practical industry is typically large-scale with more than millions degrees of freedom (DOFs). These large-scale analysis problems result in the requirements of high-performance analysis codes as well as hardware systems such as supercomputer systems or cluster systems. In this paper, the pre- and post-processing system for supercomputing based large-scale structural analysis is presented. The proposed system has 3-tier architecture and three main components; geometry viewer, pre-/post-processor and supercomputing manager. To analyze large-scale problems, the ADVENTURE solid solver was adopted as a general-purpose finite element solver and the supercomputer named 'tachyon' was adopted as a parallel computational platform. The problem solving performance and scalability of this structural analysis system is demonstrated by illustrative examples with different sizes of degrees of freedom.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.12C
• /
• pp.1029-1034
• /
• 2010

For All Digital QPSK receivers, a phase recovery scheme is required to fix the arbitrarily rotated I/Q quadrature signals due to the transmission path and clock mismatch between the transmitter and the receiver. The conventional Costas phase recovery loop scheme requires a separate AGC(Automatic Gain Control) to obtain the performance independent of input signal power. This paper proposes a simple scheme which separates the phase and amplitude of the input signal via CORDIC algorithm and performs the phase recovery and amplitude compensation simultaneously. The proposed scheme can considerably reduce the logic resources in hardware implementation, has been verified by C++ and Model Sim simulations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1936-1939
• /
• 2004

This paper proposes streaming layer for personal robot's middleware. Under assumption that robot has open architecture, i.e. consists of modules created by different vendors and intercommunication between these modules is necessary, we have to consider that there are many different network interfaces. To make communication between modules possible it is necessary to develop new type of middleware. Such middleware has to support different platforms, i.e. OS, network interface, hardware, etc. In addition, it is necessary to implement effective interface between network and application in order to manage inter application communications and use network resources more effectively. Streaming layer is such interface that implements necessary functionality together with simplicity and portability. Streaming layer provides high level of abstraction and makes communication between distributed applications transparent as if are located in same module. With possibility of extension by user defined application interfaces it is suitable for distributed environments, i.e. module based architecture including small-embedded systems like as DSP board. To verify the proposed streaming layer structure it is implemented using C and tested.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.89-91
• /
• 2004

In SCADA systems, an RTU is a device installed at a remote location that collects data, codes the data into a format that is transmittable and transmits the data back to a central station, or MTU. An RTU also collects information from the master device and implements processes that are directed by master device. RTUs are equipped with input channels for sensing or metering, output channels for control, indication or alarms and a communications port. In general, the data are transmitted via a wired communication infrastructure such as RS422 or RS485 between RTU and MTU. But, limited range of wired communication doesn't allow the system to cover remote areas over the limitation, and building a wired communication network is not easy in the circumstances. In this Paper, we design and implement a smart cost-effective Web-RTU that can communicate with MTU via Web. Web is of benefit to the Web-RTU, because it is not only free from the distance limitations, but also is built easily and cost-effectively wherever Internet resources are available. Additionally, Web can be easily applied to the SCADA system with the development of hardware and software for communications. The Web-RTU has a program memory, a data memory and a RAM inside, and uses Atmega128, low-cost 8 bit micro-processor with eight AI(Analog Input). It performs well enough to implement all existing roles of RTU.