• Restorative Dentistry and Endodontics
• /
• v.39 no.4
• /
• pp.310-318
• /
• 2014

Objectives: This study examined the influence of the resin thickness on the polymerization of silorane- and methacrylate-based composites. Materials and Methods: One silorane-based (Filtek P90, 3M ESPE) and two methacrylate-based (Filtek Z250 and Z350, 3M ESPE) composite resins were used. The number of photons were detected using a photodiode detector at the different thicknesses (thickness, 1, 2 and 3 mm) specimens. The microhardness of the top and bottom surfaces was measured (n = 15) using a Vickers hardness with 200 gf load and 15 sec dwell time conditions. The degree of conversion (DC) of the specimens was determined using Fourier transform infrared spectroscopy (FTIR). Scratched powder of each top and bottom surface of the specimen dissolved in ethanol for transmission FTIR spectroscopy. The refractive index was measured using a Abbe-type refractometer. To measure the polymerization shrinkage, a linometer was used. The results were analyzed using two-way ANOVA and Tukey's test at p < 0.05 level. Results: The silorane-based resin composite showed the lowest filler content and light attenuation among the specimens. P90 showed the highest values in the DC and the lowest microhardness at all depth. In the polymerization shrinkage, P90 showed a significantly lower shrinkage than the rest two resin products (p < 0.05). P90 showed a significantly lower refractive index than the remaining two resin products (p < 0.05). Conclusions: DC, microhardness, polymerization rate and refractive index linearly decreased as specimen thickness linearly increased. P90 showed much less polymerization shrinkage compared to other specimens. P90, even though achieved the highest DC, showed the lowest microhardness and refractive index.

• Korean Journal of Metals and Materials
• /
• v.48 no.9
• /
• pp.807-812
• /
• 2010

In this paper, the Ultrasonic Nanocrystalline Surface Modification (UNSM) surface treatment process was used to induce compressive residual stress and nanocrystalline structure by severe plastic deformation on the UNSM-treated surface. The test results for AISI304 stainless steel demonstrated that the grain size was found to be 23 nm, the dislocation density was increased by $0.2085{\times}10^{18}\;m^{-2}$, and the volume fraction of martensite is defined as 27.6% from austenite so that the surface hardness of the surface is increased from 200 Hv up to 515 Hv. The initial tensile residual stress is changed from 300 MPa to a compressive residual stress of 500 MPa after UNSM treatment. In addition, UNSM was applied under five various conditions, and the results of those conditions were defined as a function of depth quantitative.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.305-312
• /
• 2021

This study examines the damage to the submarine's escape trunk hatch spring through microstructure analysis. The cause of the escape trunk's damage during the submarine's construction and its improvement measures were reviewed. To determine the cause of breakage of the escape trunk spring, samples were taken from the damaged product and analyzed for chemical composition, hardness, and microstructure. In particular, the breakage part of the spring was analyzed in-depth by using a scanning electron microscope to determine the cause of corrosion destruction. Finally, a spring shape design method was proposed through the investigation of the cause of spring breakage. In addition, a newly improved spring was produced by applying a nylon coating with excellent corrosion resistance and abrasion resistance. Applying to an actual submarine trunk hatch revealed that the coating peeling phenomenon due to the contact between the springs is significantly improved when the hatch is opened or closed compared to the existing products.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.1
• /
• pp.94-103
• /
• 2023

The effects of carburizing pressure and gas ratio on vacuum carburizing properties (uniformity and surface characteristics) have been studied through the analyses of carbon concentration, hardness, surface color, surface roughness and type of carbon bonding. AISI 4115 steel specimens were carburized with various pressures (1, 5, and 10 Torr) at different locations (P₁, P₂, P₃, P₄, P₅, and P₆) inside a furnace held at 950 ℃. Since the carburizing pressure represents the density of the carburizing gas, it plays an important role in improving the carburizing uniformity according to locations in the furnace. As the carburizing pressure increased, the carburizing uniformity according to the sample location was improved, but the surface of the carburized specimen was discolored due to the residual acetylene gas, which does not contribute to the carburizing reaction. Therefore, the carburizing uniformity and surface discoloration have been improved by injecting acetylene gas (carburizing gas) and nitrogen gas (non-reactive gas) in a specific ratio.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.161-173
• /
• 2023

This study investigated the effects of K_N and process time on the formation of a compound layer at a nitriding temperature of 540℃ for SCR420H material. As a result of controlled nitriding from 3 h to 20 h at K_N 1.2 atm^-1/2, compound layers were formed up to about 10 ㎛, and an effective hardening depth of about 460 ㎛ was obtained. Initially, an ε+γ' complex phase was formed, and the phase fraction changed over time, and finally, the fraction of ε phase decreased to less than 1%. With higher K_N, the compound thickness increased, a pore layer was formed on the surface, and the surface hardness decreased. By applying the controlled nitriding process, it was possible to produce annulus gears with a compound thickness of 12.8 ㎛ and an ε phase of 5% or less. The annulus gears made through controlled nitriding were mounted on a 6-speed transmission and tested for durability. As a result, the durability test of 250,000 km was satisfied, and the transmission efficiency was also confirmed to be expected.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.2
• /
• pp.49-57
• /
• 2024

We investigated the changes in microstructure and surface roughness of the compound layer of GC250D gray cast iron, commonly used in brake discs, during gas nitriding. The gas atmosphere of the nitriding process was controlled with a hydrogen partial pressure of 49.5%, and the process was conducted at a nitriding temperature of 520℃ with various process times. As the nitriding process time of the GC250D material increased, both the depth of hardening and the thickness of the compound layer increased, with a maximum surface hardness of approximately 1265 HV_0.1 was measured. Additionally, the surface roughness increased with the process time. Phase analysis of the compound layer revealed an increase in the proportion of the γ' phase as the nitriding process time increased. Changes in the formation of the compound layer were observed depending on the orientation of graphite within the material, leading to the formation of wedges. Therefore, the increase in surface roughness appears to be attributed to the uneven compounds, the expansion of the compound layer and wedges formed on the surface during the nitriding process.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.30 no.3
• /
• pp.334-339
• /
• 1985

A sweet corn hybrid, Honey Bantam, was planted on 24 May, 1984 in a silty clay loam soil to investigate the effects of polyethylene(P.E.) mulch and different levels and placements of Nitrogen(N) on soil properties and sweet corn growth. A split-split plot design with three replications was employed; P.E. mulch and bare soil were main plot, N levele of 8, 12, 16, and 20 kg/10a were subplot, and band and broadcast of fertilizers were sub-subplots. At early growth stage soil temperature under P.E. mulch was higher than that in bare soil by 5-10$^{\circ}C$, but the differences decreased as plant growth advanced. Soil hardness increased with soil depth while P.E. mulch reduced soil hardness probably by holding high soil moisture. Soil pH decreased up to the 6th week after planting and then increased in bare soil, but it contineously decreased up to the 8th weeks under P.E. mulch regardless N levels and placements. Electrical conductivity(EC) of soil increased up to the 6th weeks after planting and then decreased in all treatments except broadcast of fertilizers under P.E. mulch where EC increased contineously. Generally, soil EC under P.E. mulch was higher than that in broadcast. Broadcast of fertilizers did not affect emergence of seedlings in all N levels under P.E. mulch and bare soil, but band of fertilizers at all N levels under P.E. mulch and higher levels of N in bare soil reduced emergence rate significantly. Percent stand was possitively correlated with soil EC and it strongly influenced the number of marketable ears. Plant growth was enhanced and silking date was earlier by 14-19 days under P.E. mulch compared to bare soil probably due to increased soil moisture, reduced soil hardness and higher soil temperature.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.1
• /
• pp.1-7
• /
• 2010

This study was carried out to investigate plow pan characteristics and to grasp the relationship between its particle size distribution fractal dimension ($D_m$) and water transport in paddy plow pan. Twenty four soil sampling sites with different management groups, ordinary and sandy-textured, were selected and investigated for physical properties of soils such as Yamanaka hardness in April, non-submerged condition, before rice seedling transplanting. The plow pan appearing depth and thickness was determined by penetration resistance profile. Undisturbed core samples with five replicates were sampled at plow pan layerwith 2 inch cores for measuring soil bulk density and saturated hydraulic conductivity. The particle size distribution fractal dimension ($D_m$) was calculated by the method following the procedure Tylerand Wheacraft (1992), using the USDA-based particle size analysis datawith fractions of 0-0.002, 0.002-0.053, 0.053-0.1, 0.1-0.25, 0.25-0.5, 0.5-1.0, and 1.0-2.0 mm. The plow pan of investigated fields appeared at a range from 5 to 30 cm depth, showing minimum value in sandy-textured management group and maximum value in ordinary management group. The thickness of plow pan were distributed from 5 to 17 cm, showing both minimum and maximum values in sandy-textured management group. Averagely, the plow appearing depth were deeper in ordinary management group than in sandy-textured management group, whereas the reverse in the thickness of plow pan. The particle size distribution fractal dimension ($D_m$) had higher value with finer textures, with higher fractality in coarser texture. Saturated hydraulic conductivities, $K_s$, of plow pan soils distributed from 0.5 to 1420 mm $day^{-1}$, having the highest value in sandy skeletal soils. The $K_s$ decreased with decreasing clay content and $D_m$, showing power function relationships. The coefficient of determination, $R^2$, of the fitted power functions were higher in $D_m$ as x-axis than in clay content. This means that $D_m$ could give us more effective estimation than clay content. Especially, sandy-textured paddy soils had higher $R^2$, compared to ordinary paddy soils. $K_s$ of relatively coarse-textured soils with less than 18%of clay content, therefore, was more dependent on particle size distribution than that of relatively fine-textured soils. From these results, it could be concluded that the fractal scaling gives us a unique quantity describing particle size distribution and then can be applied to estimate saturated hydraulic conductivity, especially more effective in coarse-textured soils.

• Korean Journal of Environment and Ecology
• /
• v.21 no.6
• /
• pp.487-493
• /
• 2007

This study was carried out to evaluate soil property between campsites located at Joongsanri, Daewonsa old, Daewonsa new, Baekmudong and their adjoining forest areas in the eastern area of Jirisan National Park. The survey results showed that there existed a significant difference(p<0.05) between the two areas in soil property, such as soil bulk density, soil hardness, soil pH, water infiltration and soil respiration rates. However, there was no difference in soil property by depth between surface soil($0{\sim}15cm$) and subsurface soil($15{\sim}30cm$) for the two areas(p>0.05). In case of soil bulk density, its values in campsites were significantly higher ($1.29{\sim}1.44g/cm^3$) than in forest areas($0.95g/cm^3$), while soil hardness was significantly lower(p<0.05) in forest areas($1.44kg/cm^2$) than in campsites($2.9{\sim}4.0kg/cm^2$). Soil pore space was significantly lower in campsites($45.7{\sim}51.4%$) than in forest areas(64.3%), and soil pH in forest areas indicated pH 5.46 and that of the campsites was distributed at the range from pH 6.49 to pH 6.38. In addition, water infiltration was significantly lower in campsites($0.79{\sim}2.06cc/sec$) than in forest areas(18.7cc/sec), while soil respiration rates were significantly higher in forest areas($0.58gCO_2/m^2/h$) than in campsites($0.13{\sim}0.34gCO_2/m^2/h$).

• Journal of the Korean Institute of Landscape Architecture
• /
• v.43 no.3
• /
• pp.77-91
• /
• 2015

This study aims to suggest adequate soil management through the analysis of physicochemical properties of soil in the planting grounds of Incheon International Airport, which was constructed on a massive land reclamation site. Study areas were 5 sites at the international business complex, the passenger terminal, the airport support complex, the free trade zone, and the access road. Soil profile analysis showed that 9 plots out of the 27 plots were hardpan and heterospere within 80cm from the soil surface. The earth laid on the ground was categorized as gravel based soil(4 plots), dredged soil from the sea bottom and mixed reclamation materials(2 plots), clay with poor permeability(3 plots) and waste construction material(1 plot). Average soil hardness was $11.5kg/cm^2$ and soil textures were sandy soil, sandy loam and loamy sand. Average soil pH was 6.7 and average organic matter content was 0.7%. Electrical conductivity was 0.0dS/m and exchangeable cation concentrations were $Ca^{2+}$ 3.4cmol/kg, $Mg^{2+}$ 1.5cmol/kg, $K^+$ 0.3cmol/kg and $Na^+$ 1.0cmol/kg. Average cation exchange capacity was 11.0cmol/kg. Although average figures in Solum mostly meet the landscape design criteria, properties of each soil layer showed various values sometimes over the limit. Base saturations were $Ca^{2+}$ 29.9%, $Mg^{2+}$ 13.3% and $K^+$ 3.7% for lower soil, $Ca^{2+}$ 33.3%, $Mg^{2+}$ 17.0% and $K^+$ 2.7% for mid-soil and $Ca^{2+}$ 32.6%, $Mg^{2+}$ 12.2% and $K^+$ 1.9% for upper soil. Exchangeable sodium percentages were 16.4% for lower soil, 7.5% for mid-soil and 4.7% upper soil. Sodium adsorption rates were 0.8 for lower soil, 0.3 for mid-soil and 0.2 for upper soil. Factors affecting to the vegetation growth were heterogeneity and poorness of solum, disturbance of dredged soils, high soil hardness including hardpan in the subsurface soil layer and shallow effective soil depth, high soil acidity, imbalance of base contents, low organic matter content and low available phosphate levels in the soil.