• 한국정밀공학회지
• /
• 제10권4호
• /
• pp.64-72
• /
• 1993

Analytical models for the prediction of the size of hardened zone in laser surface hardening are presented. The models are based on the solutions to the problem of three-dimensional heat flow in plates with infinite thickness. The validity of the model was tested on medium carbon steel for Gaussian mode of beam. Then the model for rectagular beam was used for the predicition of the size of hardened zone on various hardening process parameters. From the calculation results it appeared that the size and shape of the hardened zone are strongly dependent on process parameters such as beam mode, beam size, and traverse speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.26-30
• /
• 1996

This paper presents the performance of CBN tools in the machining of hardened die-materials, SKD11 and SKD61 steel with HRC 50, by high-speed face milling. Generally, grinding or EDM is being used in machining of hardened materials but the cost is very high. If those can be replaced by cutting, it will be a greatly economical advantage. CBN tool has been recognized as an effective tool in turning, but it has not been in milling. So wear and surface roughness mode of CBN tool for hardened SKD11 and SKD61 steel were investigated by high-speed face milling in this study Also the relation between cutting force and wear mode of CBN tools was investigated.

• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.267-273
• /
• 2009

Three types of structural intermetallic compounds, $Ni_3Al$, NiAl and TiAl, having each single phase structure without pores were produced by arc-melting process. Their sliding wear properties were investigated against a hardened tool steel. It was shown that the wear of the intermetallic compounds was hardly occurred against the hardened tool steel. TiAl compound showed the best wear resistance among them. In this case, wear was preferentially occurred on the surface of the hardened tool steel of the mating material which has higher hardness. It could be found that the wear mode on intermetallics without pores by arc-melting process was different from that on its porous layer coated on steel by combustion synthesis.

• 한국표면공학회지
• /
• 제47권5호
• /
• pp.221-226
• /
• 2014

A low temperature plasma nitrocarburizng was implemented on the duplex stainless steel to achieve the enhancement of surface hardness without degradation of its corrosion resistance. Attempts were made to investigate the influence of Pulse frequency and Duty factor of pulsed power in a high Pulse frequency regime on the surface characteristics of the hardened layer. The hardened layer (S-phase) was formed on all of the treated surfaces. Surface hardness reached up to 1300 $HV_{0.1}$ which is about 4.6 times higher than that of the untreated material (280 $HV_{0.1}$). The thickness of the hardened layer tends to increase lightly with the higher Pulse frequency and the higher Duty factor. The corrosion resistance of nitrocarburized duplex stainless steel was almost similar to that of the untreated material. Both the Pulse frequency and the Duty factor do not have a significant influence on the corrosion property of plasma treated duplex stainless steel.

• 한국재료학회지
• /
• 제11권11호
• /
• pp.1001-1005
• /
• 2001

In this study, the surface of 40Cr steel was hardened by $CO_2$Laser, and then the microstructural transformations and the hardness distributions of the laser surface hardened layer were observed. The experimental results showed the surface hardening layer was consisted of three parts, which is outmost surface layer of needle martensite, middle layer of martensite and remained pearlite, and transitory boundary layer. In hardness distributions, the surface hardeness of the surface hardening layer had Hv 800~1000, that was 2 to 4 times of matrix's hardness. The hardeness distribution of laser hardening layer that of surface layer hardened by general heat treatment.

• 열처리공학회지
• /
• 제5권3호
• /
• pp.165-170
• /
• 1992

The chip controls are investigated experimentally for the purpose of estimating cutting ability of hardened steel. In this experiment, hardened STD11 steel ($HR_c$ 60) is turned with carbide tool M20 under various cutting conditions and with several tool shapes. The main results obtained are as follows : 1) Cutting conditions of cutting speed 45m/min. feed 0.09-0.13 rev. depth of cut 0.4-0.6 are recommended for the chip excluding. 2) In case that the feed becomes larger and a lead angle of cutting tool becomes smaller, the chip excluding becomes easier. 3) It is confirmed that frank wear and crator wear on the cutting tool appear severely from about 10 min. after cutting start and chip excluding get worse.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.429-436
• /
• 2013

본 논문에서는 고주파 열처리된 SAE1055 베어링강의 경도에 따른 피로 거동 및 이의 확률론적 평가를 수행하였다. 이를 위하여 경도 수준에 따른 5 종류의 시험편(A : 원재료, B : HV390-전경화, C : HV510-전경화, D : HV700-전경화 및 E : HV-700 표면경화)를 준비하였다. 피로시험은 4 점 회전굽힘 피로시험기를 이용하여 응력비 R=-1 의 조건하에서 수행하였다. 그 결과, SAE1055 강의 피로 거동은 경도에 따라 크게 변화하였으나 HV510 수준이상에서는 피로한도의 증가는 관찰되지 않았다. 또한 피로 파손기구에 대한 경도의 영향을 평가하기 위하여 SEM(scanning electron microscope)을 이용한 파면 관찰을 수행하였다. 피로수명의 통계적 특성은 P-S-N(probabilistic S-N) 곡선을 이용하여 평가되었으며 이에 대한 경도의 영향은 잔류치 해석(residue analysis)을 통하여 수행하였다.

• 한국해양공학회지
• /
• 제5권1호
• /
• pp.71-80
• /
• 1991

This paper reveals the effect of the effective case depth(ECD) on the fatigue behavior of a high-frequency induction hardened SM45C in rotated bending fatigue test. In addition, the effects of fracture modes(surface origin type, inner origin type) on it are discussed. The fatigue limit of the induction hardened steel is remarkably increased compared with that of base metal. In addition, the fatigue limit is linearly increased as the effective casedepth grows deep in the region of this experiment (ECD/R;0.23-0.49). The S-N curve and fracture mode in the induction case hardened steel are classified into two kinds, as a result : N$_{f}$<10$^{5}$ ;surface origin type fracture(at high stress), N$_{f}$>10$^{5}$ ; in ner origin type fracture(at low stress). In case of inner origin type fracture; as the effective case depth(ECD) gets deep, the fatigue limit is increased by the reason that the fracture origin moves toward center; in reverse, is decreased by reason that the compressive residual stress gets low. As a result, the increasing effect of the former is much bigger than the decreasing effect of the latter, and the fatigue limit is increased as the ECD gets deep.eep.

• 한국해양공학회지
• /
• 제23권2호
• /
• pp.74-80
• /
• 2009

Surface hardening treatments, such as using the high-frequency induction hardening method, are widely used to increase the fatigue life and prevent the failure of materials by locally increasing the surface hardness. This method, in particular, brings an improvement in static strength by compressive residual surface stress due to the hardening. In this study, the mechanical properties of high-frequency induction hardened SCM440 steel were investigated. These results were also compared with those for base metal and a Q/T (tempering after quenching) treatment specimen. The test results showed that partially high-frequency induction hardened SCM440 steel specimens were more improved in static strength, surface hardness, fatigue limit, and anti-wear than the base metal and Q/T treatment specimens. In particular, the fatigue limit of the high-frequency induction hardened SCM440 steel increased by more than about 52% compared to that of base metal and by about 25% compared to that of the Q/T specimen.

• 한국재료학회지
• /
• 제3권5호
• /
• pp.538-545
• /
• 1993

초음파의 표면파의 전파특성을 이용하여 SCM440강의 고주파열처리의 정도에 따른 표면경화층의 깊이를 측정, 조사하였으며 침탄속도는 동일조직에서는 주파수에 관계없이 일정하였으나, 경화조직에서 경화되지 않은 조직에 비하여 표면파의 속도는 59m/s 늦었다. 강의 유효경화층깊이(d)와 표면파파장($\lambda_{R}$)의 d/$\lambda_{R}$의 관계로부터 경화층의 \ulcorner이를 비파괴적으로 평가, 측정할 수 있었으며 침탄경화시킨 경우에서도 동일한 결과를 얻었다.